• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Nv3550 shifting problems

tampabronco

Sr. Member
Joined
Jan 10, 2011
Messages
468
Finally got the remanned NV3550 installed and ran great for a couple weeks. Now after about 20 miles or so It won't shift into first, second and reverse. Chatters bad and pops out of second

I drained the fluid and filled with Royal purple synchromax. Ran it for a few miles and a little better but the then starts with the shifting problems again.

Any suggestions?
 
OP
OP
tampabronco

tampabronco

Sr. Member
Joined
Jan 10, 2011
Messages
468
Chatters in first when the clutch is pushed

The thing about it is it shifts perfectively when the truck is off and clutch is pushed. Turn the truck on and it won't shift
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sounds like a clutch issue then. Probably more common than 3550 issues anyway, but of course that doesn't guarantee anything.
But it sure sounds like it won't shift due to the clutch not disengaging. Did you fully adjust it to spec? Still using mechanical, or did you convert to hydraulic?

If an NV transmission gives you a rattling sound when shifting while driving, it's more often than not your rear pinion angle is not properly aligned and you're getting a slight harmonic through the driveline to the rest of the parts. Since the NV trans is the "loosest" part of the system, it's the part that makes the most noise.
Really loud when you don't have carpet or other heavy floor covering.

But anyway, check the clutch before messing with the trans more.
Is that Royal Purple the exact stuff recommended for the NV3550 trans? It's very fluid-specific, so just checking you there.

Paul
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Sounds like a clutch issue then. Probably more common than 3550 issues anyway, but of course that doesn't guarantee anything.
But it sure sounds like it won't shift due to the clutch not disengaging. Did you fully adjust it to spec? Still using mechanical, or did you convert to hydraulic?

If an NV transmission gives you a rattling sound when shifting while driving, it's more often than not your rear pinion angle is not properly aligned and you're getting a slight harmonic through the driveline to the rest of the parts. Since the NV trans is the "loosest" part of the system, it's the part that makes the most noise.
Really loud when you don't have carpet or other heavy floor covering.

But anyway, check the clutch before messing with the trans more.
Is that Royal Purple the exact stuff recommended for the NV3550 trans? It's very fluid-specific, so just checking you there.

Paul

I agree!
The NV3550 conversion uses a diaphragm clutch rather the Borg Beck three fingered type that came on many Broncos. This replacement clutch needs more travel to accommodate both full release and proper slack for the throw out bearing.
I had to adjust the rubber clutch pedal bumper eccentric up a bit to get enough travel.
It sort of screwed with my obsessive compulsive character to have the clutch pedal higher than the brake pedal.
Oh well. It shifts great this way.;)
 

jmangi62

Bronco Guru
Joined
Jul 28, 2013
Messages
2,512
When I installed mine the kit came with a couple quarts of Mopar trans fluid,and I heard that they are a brand specific trans.I've never used any other trans fluid and my trans seems to shift just fine. :cool:
 
OP
OP
tampabronco

tampabronco

Sr. Member
Joined
Jan 10, 2011
Messages
468
I bought the wild horses kit w/ the clutch & pressure plate

Sounds like I need to look at adjusting the clutch. Pretty much the same results with the either transmission fluid
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Like the Blubuck said ; the diagram clutches take way more travel than the old 3 finger style .
I like mine to engage at the top of the pedal travel - no way could i get that with this style pressure plate. It engages/disengages at the bottom - close to the floorboard.
 
OP
OP
tampabronco

tampabronco

Sr. Member
Joined
Jan 10, 2011
Messages
468
Adjusted the clutch and works great

It shifts very smooth with the Royal Purple synchromax instead of the pennzoil synchro


Thanks for the help
 
Top