• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Performance anxiety [emoji3]

bentendo

Full Member
Joined
May 16, 2010
Messages
236
Hey y'all,



Just this past year, I put a freshly rebuilt 302 (technically now a 306) out of a 1996 Explorer into my '72. The smoothness of EFI is really great, but I can't help but feelÂ… a little let down by the power. Basically, I can't seem to get good grunt in any gear. This could just be the inability of a 302 to push one of the most un-aerodynamic vehicles ever to go forward with any real purpose.



Here's the full setup:

'96 302 bored .030" over

Ford EFI

GT40 heads

Dual exhaust

Long tube headers

NV3550

4.33 rear w/ Detroit Locker

32" BFGs



I just finished a *long* roadtrip and some trail riding. The truck runs great, can keep up at highway speeds, and can even accelerate in 5th at 70mph or up most hills, butÂ… I can't make the tires chirp. It feels a little gutless. And it could be nostalgia, but my original 302 with a 4bbl Edelbrock and hotter cam felt pretty wily until it ran out of breath.



Bone stock, a '96 302 puts out 210hp and 280ftlbs torqueÂ… I'd guess with the headers, exhaust, and slight bore I'm getting an additional 15-20hp, putting me in the 220-230hp range. I also debated long and hard about the 4.33 rear (4.27 front). Everyone says "don't fear the gear", but I did. I feared the gear.



SoÂ… I guess my ultimate questions are: how do y'all feel about your EFI Explorer 302s? Anyone else running 4.33? If so, how do you feel about it? Should I just learn to stop worrying and love the Bronco as-is?



All 2¢ welcome. :cool:
 
Last edited:

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
Not sure what you are comparing it to for power?

I'm running a couple things that are the same as you. 32" tires and 4.30 gears with a Detroit. I have a C4 versus your manual. I recurved the distributor on a machine and played with jetting on the carb along with timing. The rest is basically stock. Changing the gears made a big difference in off the line acceleration as did the other little mods that I did. Even in a straight line it will spin the tires. Won't do a long distance burn out by any stretch of the imagination. Compared to stock it was an obvious difference. Compared to a couple other of my vehicles it's not very impressive. Running against it's self before and after the after is a better vehicle, against anything else, put your money in your pocket and just have fun. That's why I asked about what are you comparing it to. Against it's self in stock form how much change?


You mentioned good power in 5th under a high speed load, just no bottom end. As mentioned check your timing and fuel delivery, etc.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
In stock form, wasn't the Explorer rated at 240bhp?
What cam did you install?
Are you running a distributor or coil packs?
How big is your dual exhaust?

Did you have the computer tuned for the new setup? Exhaust and EGR delete may not be major changes, but they are changes.
What cam are you using, and did you degree it to see where it sits? Just watched the most recent Engine Power show and when they degreed the brand new cam in a Chevy 454 they found that it was already 4° advanced when installed "straight up" (meaning zero degrees) in a new build.
This is why checking cams is more important than ever before. A 4 degree difference on an Explorer cam is not a huge deal-breaker, and might be kind of fun in the low-end grunt department. But 4 degrees retarded might be kind of a bummer for someone like me that really likes the off-the-line acceleration more than the top end. You might see better performance above 4,000 rpm on an engine like yours, but in a Bronco I'm not sure most of us would actually feel the difference up there.
Maybe what you're feeling as lack of pep down low, but pulling decently once you're going is as simple as retarded cam timing. Hard to say yet...

The fact that yours can pull well in fifth gear though, tells me it's running pretty good as-is. Clean, but down on power because of the tune maybe?
As I've mentioned many times, mine is full of itself down low. But I have more gear than you by a bit. Running 4.56 with only 31" tires. An auto makes a difference too.
By the way, what is the exact size rating on your tires, and what is the actual diameter of your tires?

Paul
 
OP
OP
bentendo

bentendo

Full Member
Joined
May 16, 2010
Messages
236
What cam did you install?
Are you running a distributor or coil packs?
How big is your dual exhaust?
Did you have the computer tuned for the new setup?
What cam are you using, and did you degree it to see where it sits?
By the way, what is the exact size rating on your tires, and what is the actual diameter of your tires?

– Stock cam
– Coil packs
– 2.25" pipes off Duff's long-tube headers. Turbo style mufflers.
– EFIguy reprogrammed based on EGR and CAT deletes, as well as making allowance for standard trans
– Did not degree the cam
– Exact tire specs: BFG TA KO2s 32" x 11.5" on late model bronco 15" alloys
 

lars

Contributor
Been here awhile
Joined
Jun 29, 2001
Messages
3,334
Loc.
NorCal flatlands
408 joy. Still needed a lot of tuning when the video was taken. Replaced a sweet running Explorer 5.0 that delivered 20+ years and 120k+ miles of service. But there is no substitute for cubic inches. It. Just. Goes.

https://www.abarinnowhere.com/Bronco/408/n-34d734/i-x7tv3gH/A

Ok, my motivation for the 408 swap...

My Bronco was and still is geared 4.56, 35" BFG A/T KO2's, NV4500. My 5.0 was a 98 Explorer with gt-40p heads, stock Explorer intake. Comp Cams 35-308-8 cam, which was probably a mistake. Too much midrange at the expense of low end torque. WH shorty headers exiting through 2.5" tubes into a 3" single Dynomax muffler, single 2.5" out the back. Mustang 5.0 electronics, A9L ECU with a Tweecer so I could run EDIS and make some other minor tuning changes.

No way could I spin those tires with that engine on dry pavement. At sea level, empty, it pulled pretty well once it was rolling, though it wasn't going to set any acceleration records. A stock Honda Accord would have easily taken it.

I run a full time hard top with a full cage, dual tanks, etc. With full tanks it weighed 5200 pounds, which is part of the problem. At altitude, say 5000 feet and above, loaded with gear going up a grade, I was in the slow lane in 4th and sometimes 3rd.

Since loaded traveling is my primary use for my Bronco these days and I like the suspension-tire size combo, it was either re-gear or re-engine. I chose the latter. In your case I'd consider 4.56 gears.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Borrow a couple of smaller tires and put them on the back and take it for a drive. it will tell you if its gear or not. you should be able to roast a stock size tire with the gearing you currently have. if not I would pull the timing cover and check cam timing. have you done a compression test on all cylinders? Personally if it were mine I would run the cam 4 degrees advanced and 10 to 12 degrees advanced in timing. total advance timing at 30 degrees at 3000 RPM. how you get their with your efi set-up I don't know. I am not efi savvy.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yeah, something does not sound right. With that setup and a stock cam and tuned, your low-end off-idle response and acceleration should be pretty gnarly. Chirp those tires no problem I would have thought.
My impression is that the stock cam does run out of breath earlier than others, but it sounds like you have the opposite of that. Mine runs consistent with what I would have surmised. Hard pulling off the line (can almost NOT keep the tires from squealing. Yes, really) but runs out of whatever it is that we're feeling when I'm trying to really romp on it or accelerate hard at freeway speeds.

It runs sweet also, and will idle all day and pull stumps and get 20mpg in the bargain. But it's not a race engine with high power at full throttle.
Mine differs from yours in at least one key area though. Exhaust. I have stock Explorer manifolds for the P heads and a single 2.5" exhaust with Magnaflow muffler and cat. So I'm much more restricted than yours. Could that be the root of the issue? Maybe the tune is slightly off for such a free-flowing exhaust?

For comparison I can literally roast the tires on dry pavement and can almost not use the truck in the rain. It's so strong off-idle that it's very hard, even with my very light right foot, to start the Bronco rolling without spinning the tires uselessly. As I've said before, I had to modify my aggressiveness around town to the point where I no longer try to merge with the flow of traffic if the pavement is wet. I just can't push the throttle down the normal amount to accelerate. The truck just sits there and spins the tires.
Yes, it's that bad. So I just wait my turn after the last car, rather than try to fit into gaps like I normally would.

What is your intake setup? Where is your MAF sensor and air filter? What size intake tract tubing? Does your exhaust have a cross-over of some type, or are they discrete duals?

Paul
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I assume you're running Explorer EFI. On Explorer EFI, isn't the timing fully controlled my the ECM meaning you can't change it without getting into the tune?

Stock cam or aftermarket?

Tim
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Stock cam he said. I'm assuming stock "Explorer" cam since he indicated it was a '96 Exploder engine.
My original '71 with stock cam would not spin 32" tires with 4.11's and a manual trans to save it's life either. But I'm sure my stock Explorer setup would!

I think you're right bentendo. The '96 was rated at 210bhp but that still puts it at probably a minimum of 50hp higher than the 205hp rating of my '71. They used the "gross" power method back then. Engine tested bare with no accessories and probably a dyno exhaust.
In '72 they started using a "net" method where the power ratings were dyno'd with everything it would have had when driven in the vehicle. Which is why for '72 the numbers went down between 40 and 60 horsepower on paper even if the engine was the same one.

Seems like yours should feel stronger than you're seeing.
Have you reached out to EFI guy with any questions about tuning for more power? Might be possible.

Paul
 

BanditBronco

Sr. Member
Joined
Jul 2, 2008
Messages
690
408 joy. Still needed a lot of tuning when the video was taken. Replaced a sweet running Explorer 5.0 that delivered 20+ years and 120k+ miles of service. But there is no substitute for cubic inches. It. Just. Goes.

https://www.abarinnowhere.com/Bronco/408/n-34d734/i-x7tv3gH/A

I got excited, I thought we were going to get a burnout video Lars....

Everyone says they can roast the tires, yet I have never seen proof. Cough cough... Paul...

OP it sounds like your gearing is good, being able to pull hills in 5th is not an easy thing to accomplish. With that said, if you are comfortable growing some rpm, some extra gear shouldn't hurt you too much up top. What happens if you dump the clutch?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Everyone says they can roast the tires, yet I have never seen proof. Cough cough... Paul...

Hah! Yep, I'll have to have proof one of these days. Just borrowed a go-pro to record axle wrap changes, so may have to set it up looking the other way to see what we get. Hopefully the sound comes through on the small chirps.
We'll see.

I know, I know... Pics or it didn't happen!

Paul
 
OP
OP
bentendo

bentendo

Full Member
Joined
May 16, 2010
Messages
236
Seems like yours should feel stronger than you're seeing.
Have you reached out to EFI guy with any questions about tuning for more power? Might be possible.

Just reached out to him, we'll see what he says. It could very well be that I neglected to give him all the info needed when he reflashed the ECM.
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
I went thru something like this with the bone stock (except for cold air) 5.0 in my Mustang. Stock it was nothing to brag about. I added some of the stuff you have already done (GT40 intake, GT40 heads, MAF, custom chip, etc) Each mod added something to the performance and the cumulative result is very satisfactory (and a little scary in a 50+ year old missile).
 
Top