• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

power steering bleeding issues..

Mark

Contributor
Bronco Klutz
Joined
Aug 29, 2003
Messages
5,417
Loc.
NW Indiana
Well, I've bled power steering a number of times, but for some reason this time it's not happening!
Background...
I recently installed a brand new Saginaw pump with dual returns from WH, I put a 4x2 box on that was working fine on my other Bronco. I have Hydo-boost and here is how I have the lines run...
High pressure from the pump to H-boost,
High pressure from the H-boost to the high pressure feed on the steering box,
return line from the H-boost to the pwer steering pump,
low pressure - return line from the steering box to the pwer steering cooler and then from the cooler to the 2nd return on the pump.
issues...
With engine off... turn wheel from lock to lock a hundred times, still feel jerky resistance... turn engine on... sitting there idling, no bubbles form in pump.. I touch the dang steering wheel to turn it from lock to lock with engine running (front end jacked up) and the steering wheel forcefully starts shaking back and forth! along with the drag link, tie rod, and etc... shut engine down examine everything.. foam visible in pump... turn wheel lock to lock again and again with engine off, still jerky feeling through wheel. repeat this process a few times, and finally just left engine running with steering wheel violently shaking back and forth.. well, now something gives, my steering box seal where the steering shaft couples to the box, pukes fluid everywhere. "luckily" I have another 4x2 box laying around, install that, and the same thing is happening... I'm not going to risk blowing the seal on this one.
The only thing I can think of to do now is with the engine running remove the return feed line going to the cooler from the box and see if I'm getting good flow of fluid from the box. maybe that return line is restricted...? I have 5/16" brake line screwed into the box, but maybe that's too restrictive??
any other thoughts...
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
check you lines first..
if they are good remove the high pressure feed to the box and stick it in a bucket.
crank engine until fluid comes out
reinstall hose
start the bleeding procedure over again( turning wheel back & forth a lot)
 
OP
OP
Mark

Mark

Contributor
Bronco Klutz
Joined
Aug 29, 2003
Messages
5,417
Loc.
NW Indiana
thanks guys..

Double checked layout of lines. All as should be, listed layout in original post.

Pretty sure I'm getting good flow to the box on the pressure side, blew out seal on first box. but if it's restricted on the outflow, that would explain blown seal (too much pressure inside box)... gonna remove the coil wire and crank engine and check the outflow from the box (return line)...
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
Mark-

Pull the coil wire...so it cant fire. Turn the motor over a few times-this flows fluid more slowly than if the engine 'catches'. Cardinal rule is never to actually fire the engine to intially prime the system. Always use the starter--with the engine disabled. Apparently, you have alot of air in there. Do the above a few times, let it sit for 5-10, repeat, then cylce the steering a dozen times (or more), then repeat the above. I also activated the starter with the brake pedal pushed, so that fluid would flow through the boost-unit. After repeating all of the above at least 2X, I then started it. After I had it running, I cycled the steering wheel ALOT, then pressed the brakes several time, then the wheel , then I cycled the steering wheel while pushing the brakes, this is what finally got the last of it out.

Good luck.
 
Top