• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Power Steering upgrade?

raging56

Full Member
Joined
Jan 18, 2009
Messages
172
Loc.
Scarborough, Maine
I have a 1966 bronco and I need power steering bad.

What do you guys suggest? I have an automatic with 33" tires and I may even go with 35's someday... the engine is a 289 and I might go with a 351 someday.

I just want a dependable system that will not give me any issues or struggle with tire sizes. I see some kits that are about $850.00 and up. Is there a "go to" kit I should go with?

I was thinking of something like this...
http://www.cjponyparts.com/borgeson-power-steering-conversion-kit-170-200-bronco-1966-1977/p/PSK24/

What about the steering shaft? Should swap that out too? or no need?

Any help is appreciated! and I will continue to search...

thanks!
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
You should replace the original one piece steering shaft with a modern collapsible shaft, the old ones are well known for spearing through the driver's chest in an accident.

From what others have said, that steering system is good up to the largest size tire you say you will use.
 

BR549

Sr. Member
Joined
Jan 18, 2012
Messages
444
Loc.
huntsville
If I remember correctly BC broncos has a good write up on steering boxes with pros and cons.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I'm running the Borgeson Delphi box and have been for 3 or 4 years now. Works great with my 32's. I ran a stock pump and bracket but am upgrading to the canned ham pump with my 351W upgrade currently in the works. I like the extra mounting hole the Delphi box has.

X2 on upgrading the shaft to a 2 piece or a 2 piece collapsible. I run a stockish 2 piece noncollapsible.

The main issues no matter what box you go with is the frame and flexing. I suggest removing the old box, fix any cracks then plate both sides of the frame. I used 3/16th plate. Knock out the weak supports in the frame and replace them with 1/4 inch DOM tubing. If you do all that, you will have a rock solid mount for any box.

I think BC states the Delphi box is good up to 35's. I plan to move to 33-34's in the near future if the 351W/EFI/Bench seat upgrade ever gets finished.

Shop around for price as that box is $549 at most places. I got mine off Ebay for I think $399 free shipping but it might have been $499 FS

Tim
 

Pops68

Contributor
Bronco Rookie
Joined
Oct 11, 2010
Messages
1,777
Loc.
Bazetta Township
I bought Tom's top of the line kit about 5 years ago for around $1200 it is around $1500 + now. Easy install and works fine - great customer support, too. I have a 351 and 33's and no issues since install.

Pops
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
4x4x2 box with a Saginaw pump. You cN get the needed brackets and pulleys from the vendors. Wcb sells a frame brace for this set up. You can run a ujoint in the steering shafts and get by.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
There are so many different ways to do this. No one answer is correct. From stock used parts that pretty much just bolt on all the way up to brand new steering boxes that are real close to a bolt in. And a vast array of junkyard choices as well. Some will require a little fabrication, others a lot more.

On the engine side you need a pump. Really any pump can be used with any steering box. They are not paired. There are differences, mostly in the pressure ratings. Usually a pump from a rack and pinion system is set to a lower relief pressure than a regular steering box. Flow rates are not that big of a deal at your level either. You just need something that will bolt to the engine and be driven off a belt.

On the frame side you need a steering box. Rubber high pressure hose needs to have matching fittings for the pump and the box. Sometimes adaptors are needed. Return being low pressure hose is fairly simple. Just be sure to use power steering or transmission cooler hose. Parts store people love to roll out rubber fuel hose and sell you that. Not good, make sure it is labeled power steering and/or transmission cooler hose. The rubber is different, matched to the fluids.

Then there is the steering shaft. For as simple as it is, it can be one of the toughest parts to get. Typically 2 universal joints and some slip shaft in the middle is the best option. Unless you are getting a new shaft (maybe a new column?) you will probably find yourself cutting down the original shaft. Again many options for fitting a U-joint to that shaft.

Many options (besides a stock steering box) will also require steering linkage mdifications.

So it isn't going to be a quick cut and dry answer to what to get. Budget and fab skills/equipment also play a huge factor. As well as what you can find.
 
OP
OP
raging56

raging56

Full Member
Joined
Jan 18, 2009
Messages
172
Loc.
Scarborough, Maine
Good info...

Ill be sure to replace the shaft and beef up the frame where the steering box will mount.

Any advice on how many turns i should be at? Lock to lock? Whats the most popular? I had a 75 bronco with power steering and i liked the ratio. What price range should i be looking at for a steering box? Should i go new or is rebuilt ok?

Thanks!
 
Top