• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Speed matched clicking sound Need help.

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
Totally new build, completely bottom to top. Doing a break-in ride, engine everything runs great.

However, I can hear at speed (velocity, not RPM) a clacking sound. Faster I’m going the faster it is. Possibly front right. Doesn’t do it under engine acceleration or deceleration. Does it with clutch in (while in gear) or in neutral. If I put it back in gear and accelerate it goes away. Under hard braking it seems louder even when I stop braking while moving.



Thoughts?
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
Might check your hubs on the front and see if someone locked one side in. Happens all the time in my neighborhood.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
I've had wheels that were loose on the hub when the lugnuts were bottomed out tight.
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
Will double check the hub to wheel. I checked the hubs earlier and both say “free”. Plus I can spin the front driveshaft by hand with the tires on the ground.
 

Bradsp8

Sr. Member
Joined
Mar 5, 2005
Messages
599
Start simple. Check for a rock stuck in the tread. Then look for or a nail/screw/some piece of metal embedded in your tire. Then progress to hub, bearings, etc...
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
Best way to check for this problem?

Trying to remember, that was 28 years ago. I knew what loose lugnuts sounded like and was chasing that issue.

For you, I would jack a wheel up, check for play, set it down, jack it up, rotate 180° and watch as you set it down.
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
Start simple. Check for a rock stuck in the tread. Then look for or a nail/screw/some piece of metal embedded in your tire. Then progress to hub, bearings, etc...


Definitely not something in the tires. Goes away even with very light throttle. Clacking sound, shouldn’t be there. Much louder during full stop braking. Can feel it in the shifter as well. In the drivetrain somewhere.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Alex, I'II taking U joint for $1000 because every time I've had a speed clicking noise it's been a rock or something in my tire or U joint.

Have someone walk along side the rig and drive slowly and have that person listen for where the sound is coming from.

Tim
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
I’ll do the walking test. Brand new u-joints and haven’t been near rocks yet. I’ll grease everything when I get home.

Any greases not to use? Front end is a rebuild Dana 44 with disc brakes from Tom’s.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
I’ll do the walking test. Brand new u-joints and haven’t been near rocks yet. I’ll grease everything when I get home.

Any greases not to use? Front end is a rebuild Dana 44 with disc brakes from Tom’s.

Well on new U joints, I once lost a needle bearing from a cap while installing the U joint. Not saying that's what happen but when all else fails to turn up the issue, you have to start thinking outside the box at the What if's. ;D

Tim
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
So locking front hubs didn’t make it go away. Can’t get the atlas 2 in front H right now, something blocking it. Just front low it hops quite a bit. Feels like it is in the transfer case, wondering if front is trying to engage just a bit? Will see if I can adjust the front output to work in front high. If it is partial engagement here it will go away. Can also feel it in the short shifter that was installed on the AX15.
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
Angle.

932B84F0-D3F8-4599-9D9A-18A6FBE69AC1.jpg

Pinion on the rear.
 
OP
OP
T

T-7ToNewOldB

Full Member
Joined
Dec 7, 2018
Messages
315
Advance Adapters feels that the fact that it only makes noise when coasting is do to vibration using up the backlash and chattering the gears. Under acceleration or deceleration (acceleration in the opposite direction for the physics nerds) the gears are pressed together and so the backlash is kept from closing completely. Also gets worse as it warms up, which they felt converted it. Due to improperly welded perches I have to put about a 15 degree shim in to correct this. Hopefully this fixes it, will try and figure out by the weekend.
 
Top