• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Steering Column Re-assembly

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
I've missed something putting my steering column back together.

I have a stock column that has the smooth shift collar, no shifter components inside, and a Grant GT wheel so the horn stuff is all out.

I think I'm missing some stuff in there, because when I put the wheel on it tightens down to the point it presses against the collar behind it and of course won't turn and I don't want it to so much as rub.

What do I need to do to get the steering wheel bumped out enough it does not touch the collar behind it? The spring is not enough.

Here are some photos that might help explain:
 

Attachments

  • IMG_1882.jpg
    IMG_1882.jpg
    59.8 KB · Views: 254
  • IMG_1881.jpg
    IMG_1881.jpg
    117.8 KB · Views: 306
  • IMG_1880.jpg
    IMG_1880.jpg
    64.4 KB · Views: 312

BRONCO26

Sr. Member
Joined
Jan 17, 2006
Messages
508
Loc.
SENOIA
I just change my 3 spd col to auto and I have a grant wheel also and the collar rubbed the shift tube so I took a ziz wheel and very carefully trimmed some off of the steering wheel collar. I think my grant wheel originally came with 2 collars tall and short. I hope that helps it fixed mine.
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
You're missing the metal bushing thingy that slips over the steering shaft before you put the spring on. You can get plastic ones, but on the Broncos I have worked on, the plastic ones go in the bottom of the column in the engine compartment. The ones at the top in the cab are metal. I suppose a plastic one would work OK. I would be concerned about the pressure put on it from compressing the spring.

http://www.tomsbroncoparts.com/product/steering-column-bearing-sleeve-66-73-early-ford-bronco-new
 
OP
OP
Airmapper

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
You're missing the metal bushing thingy that slips over the steering shaft before you put the spring on.

Thanks, speaking of which I need to double check that the plastic one is on the bottom. I think it is.

Anyone have a pic of this top bushing? I think I may be missing it completely as I don't recall it coming off either column I had. I'll look through the junk I took out, might have been something I overlooked.
 
OP
OP
Airmapper

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
I've been messing with this some with no luck, for one I been cleaning up the shed and I can't remember where I put all my column take off junk (I had 2 of them so I had extra pieces.)

Anyway, what do those 2 square head bolts hold on? I do not have those in there and my smooth shift collar and the signal switch housing are very loose. That might be part of my issue?
 

Lunar-tic

Sr. Member
Joined
Sep 28, 2009
Messages
629
Loc.
Brentsville
The two square headed bolts hold the turn signal housing on which in turn holds the shift collar in place. Wild Horses has a good video on youtube that shows you how to take it all apart and put it back together. Once all that is tightened down, attach the wheel and loosen the bearing retainer clamp on the shaft on the south end of the column (engine compartment) and pull the shaft up if necessary. You may not need to but if you do/can make sure to reposition and retighten the lower bearing clamp. Watch the videos, they make more sense.
 
OP
OP
Airmapper

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
Thanks William. I got the collars secured now, watched the videos, Jim is the man!

I still have it too tight, but I discovered in addition to not having a metal busing thingy I don't have the snap ring either. (Probably lost it.) I need to find those I suppose, then if that still doesn't help I'll need to trim the collar down a bit. It's not interfering a lot, just enough to bind up the wheel.
 

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
Mine was tight against the steering wheel adapter. Where the column mounts behind the dash there is some room for adjustment. You will have to go under the hood and loosen the bearing retainer and the large clamp that holds the column.
 
OP
OP
Airmapper

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
I think I have it adjusted as far as it will go. It was a major pain in the rear to get anywhere close to straight. I got one of those Bronco script covers for the column hole and I only barely got it to fit on, and that is budging it down a little bit with a spacer. but I did put it as far back as it would go.

My lower steering shaft is somewhat adjustable / collapsible, I have an inch or two of adjustment there, but it is very tight and hard to move. I loosened that clamp at the bottom and tried to pull the shaft up a little more but I couldn't get it to move. Might try it again if I can get someone to help.
 

firehawk

Sr. Member
Joined
Jun 27, 2006
Messages
614
Loc.
Clawson, Michigan
I think I have it adjusted as far as it will go. It was a major pain in the rear to get anywhere close to straight. I got one of those Bronco script covers for the column hole and I only barely got it to fit on, and that is budging it down a little bit with a spacer. but I did put it as far back as it would go.

My lower steering shaft is somewhat adjustable / collapsible, I have an inch or two of adjustment there, but it is very tight and hard to move. I loosened that clamp at the bottom and tried to pull the shaft up a little more but I couldn't get it to move. Might try it again if I can get someone to help.

If you have trouble getting the trim piece on around the column at the dash, the dash can be adjusted by loosening all the bolts and it should slide around a little.

My trim piece won't fit on right now either and that is what I need to do.
 

Lunar-tic

Sr. Member
Joined
Sep 28, 2009
Messages
629
Loc.
Brentsville
You'll have to loosen that lower bearing retainer clamp a lot, maybe even tap it with a hammer to work it loose. Slide it down the shaft a little and then (what I did) tap the back of the steering wheel with a rubber mallet to get it to move the desired amount. Make sure to protect the steering wheel with a cloth. Once you have it where you want it, reseat the lower bearing clamp and tighten it down. I just did the same procedure when I did my power steering upgrade, had to buy a new upper bearing bushing and spring but, now it works perfectly. Maybe your lack of a lock ring is letting the steering wheel seat too far down on the shaft? I don't have one either but, mine doesn't seem to need it.
 
Top