• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tailgate repair patch panel?

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I was wondering if anyone makes a repair patch piece to section in the usual rust area. I searched but can't find it so I assume not. It would be nice to have the curved section rather than having too section it in. Anyone know if one exists?
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
Thanks so much. I searched and never saw that one. Exactly what I was looking for. I appreciate it.
 

RVB

Contributor
Full Member
Joined
Oct 30, 2007
Messages
315
I have heard that the repair panels are not the same gauge as the original, but don't know that for sure. I am sure someone does,however. Anyone with first hand experience?
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
You can take a piece of 16 gauge sheet and form it over a pipe that is similar diameter to the bottom of the tailgate. Takes a little patients but comes out very nice.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
You can take a piece of 16 gauge sheet and form it over a pipe that is similar diameter to the bottom of the tailgate. Takes a little patients but comes out very nice.

Thanks but for 60 dollars I think this is a better way to go.
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
I agree, sometimes it is better to just get the right part. I was just throwing that out there in case you didn't like what you found.
 

71broncman

Sr. Member
Joined
Sep 6, 2009
Messages
410
Loc.
Maysville, Ky
I used the Duff's patch on mine and highly recommend it too. I bonded it in with 3M Panel Bonding Adhesive and sanded the excess down at the transitions. After paint you can't tell it's not original.
Mark.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
I used the Duff's patch on mine and highly recommend it too. I bonded it in with 3M Panel Bonding Adhesive and sanded the excess down at the transitions. After paint you can't tell it's not original.
Mark.

Thanks Mark, I am a bit curious about the process. Did you cut out and replace (weld)the metal patch or cut out the rust and this overlays over the entirety including cut out?
 

71broncman

Sr. Member
Joined
Sep 6, 2009
Messages
410
Loc.
Maysville, Ky
I cut out the rust and treated the remaining metal with phosphoric Prep and Etch (Clean Strip brand). The patch panel comes up to the angled transition on the outside of the tail gate. It goes up to the ridge on the inside about 1 1/2" from the bottom. I cleaned the whole area the patch covered down to bare metal and scuffed it well with 80 grit paper. I also scuffed the inside of the patch the same way. I then test fit the patch and predrilled 5 evenly spaced holes for rivets on the inside of the tail gate. I spread the adhesive over every bit of the area the patch covered, then slipped the patch into place. I riveted the inside then used 6 bar/pipe clamps from top to bottom and about 10 "C" clamps with strips of 1"X2" between each pair to distribute the pressure across the whole outer face. Let it set for 24 hours, pulled the clamps, then sanded the excess that squeezed out when the clamps were tightened. I had also pre-marked the drain and license plate light holes so those were also drilled at that time. I'm pleased with the results, and all the other Bronco owners that live around me can't even tell it's patched. Hope this answers any questions you had.
Mark.
 

bosshoff

Sr. Member
Joined
Mar 30, 2004
Messages
726
I got one these lower tailgate patch panels from the Graveyard. It worked well. The 3M panel bonding is the only way to do this. I had a friend tig weld it, an he screwed it up by not adequately tacking it in place. The patch kind of "walked" on him. It is solid, and that is all I wanted or needed for my trail rig. Had it been a "restoration" the job would have been ruined. Don't cut anything out until you have the replacement panel in hand. You don't want to trim anything too far back.
 
OP
OP
ngsd

ngsd

Contributor
Bronco Guru
Joined
Mar 2, 2019
Messages
2,702
Thanks. Ordered one from Duff but the shipping put it out of consideration. 59 dollars for the part but 49 dollars to ship it. I will look around. I appreciate the comments.
 

Wyattman2015

New Member
Joined
Oct 10, 2022
Messages
42
I cut out the rust and treated the remaining metal with phosphoric Prep and Etch (Clean Strip brand). The patch panel comes up to the angled transition on the outside of the tail gate. It goes up to the ridge on the inside about 1 1/2" from the bottom. I cleaned the whole area the patch covered down to bare metal and scuffed it well with 80 grit paper. I also scuffed the inside of the patch the same way. I then test fit the patch and predrilled 5 evenly spaced holes for rivets on the inside of the tail gate. I spread the adhesive over every bit of the area the patch covered, then slipped the patch into place. I riveted the inside then used 6 bar/pipe clamps from top to bottom and about 10 "C" clamps with strips of 1"X2" between each pair to distribute the pressure across the whole outer face. Let it set for 24 hours, pulled the clamps, then sanded the excess that squeezed out when the clamps were tightened. I had also pre-marked the drain and license plate light holes so those were also drilled at that time. I'm pleased with the results, and all the other Bronco owners that live around me can't even tell it's patched. Hope this answers any questions you had.
Mark.
Hi Mark
You wouldn't happen to have any photos of how you clamped it or a little more on how you clamped it.
I want to go this direction but I am just cutting my teeth in this.
Much appreciated.
Robert
 

71broncman

Sr. Member
Joined
Sep 6, 2009
Messages
410
Loc.
Maysville, Ky
Robert, Sorry, but I didn't take any pics. I installed the pipe clamps about 2" from each end then evenly spaced across the rest of it. I placed the 1"x2" strips about 1/2" down from the top, under the pipe clamps, then installed the "C" clamps. The "C" clamps I snugged down to hold them in place then tightened the pipe clamps to pull the bottom tight. I started from the center two and worked out to each end. Then I tightened all the "C" clamps also working from the center out each way to the outside. The adhesive squeezed up out the top a little, which I sanded flush with the transition when it was dry the next day. Hope this helps.
Mark.
 
Top