• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tech Lessons (Newbie Mistakes)

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
How about a list of mistakes learned the hard way? I'll start it off with an easy one most of us have done once.
1) Always check to make sure the gasket comes off with old oil filter when changing.
 

Airmapper

Foolproofness Tester
Joined
Mar 15, 2006
Messages
1,710
Loc.
Bowling Green, KY
Ha ha ha, I thought I blew my engine up when I did that.

2) Always reconnect ALL ignition components before attempting to start engine. Especially the ignition module.
 

Toddpole

Sr. Member
Joined
Jan 2, 2008
Messages
832
#1 happened to me while driving after a cam swap.
#2 happened to me on a different vehicle I owned in college.

3)Be SURE to put OIL in the engine on initial start up after a rebuild!
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Make sure when you buy oil and filter......the filter in the box is the correct filter for that box and verify some a$$hole didn't put something inside the filter and the #1 thing......make sure the oil you buy is NEW and not used oil someone put back in the jug and returned to Wal Mart.

Yes it happen to me....got home and the oil was USED......I was so pissed...I now take the top off the 5qt jug and verify it's sealed.

Tim
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
when installing ball joints make sure the grease fitting hole is pointed to where you can grease it, when fixing it make sure you put the boot back on.
 

BRONCONY

Jr. Member
Joined
Jul 28, 2013
Messages
99
Loc.
North Eastern, NY
Make sure to have the ignition wire on the right side of the coil before turning the key! Or your me pretonix igniter will smoke!
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Make sure you have the correct (164 tooth) flexplate in place before you button everything up.
The starter would just spin and spin........very sad.
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
when rebulding an engine make sure you put the rear main seal in before you put it back in and have everything bolted back up%)
 

Desert Dweller

Sr. Member
Joined
Jan 20, 2011
Messages
381
Loc.
Central WA
This one wasn't me, but a friend with 40+ years of engine building...

*Make sure the front oil galley plugs are in before installing timing gear set, front cover, etc.....
:cool:
 

weasel

Sr. Member
Joined
Apr 21, 2008
Messages
438
Loc.
Norfolk
After purchasing a new crate motor, dont just assume it has the same firing order as the one your replacing. Took me a week and multiple phone calls to find out my new 302 had a 351 firing order. %)
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Not mine, but I was helping...make sure the torque converter is fully seated prior to transmission installation and engine start-up or you'll lose the tabs on the front of the pump.
 

joshnjulie1

Sr. Member
Joined
Jul 11, 2012
Messages
891
Loc.
Moreno Valley, Ca
When working on a project/part, find the parts you need, get them ordered, adn have them delivered before you JUMP into it on the weekend.

Nothing like ordering lsat minute or opening the box last minute only to find the pieces you ordered are not right. Talk about a weekend killer.
 

siderbox

Bronco Guru
Joined
Nov 5, 2007
Messages
1,119
Never put an oil drain plug in finger tight with the intention of tightening later.
Don't ask.

I always tell people, right after I give them words of wisdom like the ones stated in these posts.
"I didn't read this things in a book, trust me."
 

JT

Full Member
Joined
Sep 14, 2012
Messages
159
Don't take your windshield glass out of the frame with a 15" flat blade screwdriver unless you want to crack the glass.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Don't take your windshield glass out of the frame with a 15" flat blade screwdriver unless you want to crack the glass.

LOL....tell it like it is brother....broke mine taking it out and was so dumb I broke the new one putting it in.

Tim
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I've owned my Bronco for 17 years (plus I'm getting old) so I'm hardly a newbie!

Should someone start a new thread "Tech Lessons (Veteran Mistakes)"? I may be able to make a contribution or two...:-X
 
Top