• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tips for steering yoke

77bronk

Full Member
Joined
May 1, 2014
Messages
182
Loc.
Fort Worth, TX
About to install a new steering yoke . Mine has a lot of play and I think that's where my loose steering is coming from . I can grab the shaft (gigity) and rotate the steering wheel quite a bit before it starts to turn the rest of the yoke.
Do y'all have any tips? Taking off and install ? I've never done this before and don't know how it all goes together . Was going to wing it and drink some beers and figure it out I guess lol

85611227-0EC4-44BC-9FFB-EFCFB23EF489_zpsjb6zu6z2.jpg


8FDE2589-AD8D-4608-97DD-9277AB2057A1_zps3xnxlbhz.jpg
 

phldwsnoc1

Jr. Member
Joined
Feb 13, 2012
Messages
81
Loc.
Jarrettsville, MD
Looks like if you can replace a ujoint, you've got this one licked. I see the pinch bolt on the gear side but not sure how the yoke is attached to the shaft side. I'd say 3-4 beers for a successful repair. Good luck!
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Might want to research this further. You're looking at welding for that U-J to work. I seem to recall that maybe a Cherokeee part works in this application?
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
On the u-joint you show in the picture, is the shaft side just a round slip joint, or is it double D? If just round slip, you have the wrong joint. You need a double D joint at the shaft side with a couple of set screws. For the most peace of mind, drill two pilot holes in your shaft for the set screws.

Wildhorses sells the correct joint to replace the stock one you currently have.
 
OP
OP
7

77bronk

Full Member
Joined
May 1, 2014
Messages
182
Loc.
Fort Worth, TX
I ordered it from wh. Says yoke for stock power steering and this is what they sent ? Are you saying this is the wrong one ?
 
OP
OP
7

77bronk

Full Member
Joined
May 1, 2014
Messages
182
Loc.
Fort Worth, TX
Oh sorry I didn't understand your question . Here's a better side shot of the new one. Weird part I guess I have to reuse some of the old hard wear. Only came with 1 nut and bolt

04996510-EE77-49F6-A260-75B6F93116DD_zpsyxgpmkdm.jpg
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
The part on the left in your photos is smooth and round. The lower part of your steering shaft that you're going to install this on isn't round. It's what's called a double D shaft. I would not use that on your shaft as it leaves the possibility of the double D shaft just spinning in the round hole.

I'd use this one:

http://www.wildhorses4x4.com/product/Flaming_River_Steering_Yoke_FR1719
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
I ordered it from wh. Says yoke for stock power steering and this is what they sent?

You have the joint for a 73-75 lower shaft. Not the joint for the 76/77 lower shaft. You have a stock 76/77 collapsible lower shaft on your Bronco. You need the correct replacement joint for that shaft, which I'm 99% sure is the one I linked to in my previous post.
 

clarrance

Bronco Guru
Joined
Mar 3, 2005
Messages
2,675
I've been down this road. The 76/77 lower joint is not serviceable or replaceable. It is welded on the double D shaft from the factory. The only way is to cut the shaft at the joint buy a double D u-joint and place it on the shaft, but then guess what the shaft becomes too short. I then bought a new piece of double D shaft cut it to length and pieced it together. Problem is the factory shaft has a spring type tension piece that keeps the shaft from rattling around. This will not work with the new double D shaft without some machine work.

By the time I was done screwing around I had spent $125 on parts which left me with a rattling shaft. Do yourself a favor and buy the complete shaft from WH for $225. It will be money well spent.
 
OP
OP
7

77bronk

Full Member
Joined
May 1, 2014
Messages
182
Loc.
Fort Worth, TX
Well shit . Y'all are all downers lol. I appreciate all the info . I'll just return this one then and get the complete shaft if that's the case .
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
I don't see how replacing the u-joint will make the lower section too short. The replacement u-joint is maybe an inch shorter than the stock one at most, and there's certainly an inch of play in the telescoping shaft.

Regardless, if you end up buying a whole new shaft, you don't need the complete $250 one. WH sells just the lower half of the telescoping one for $120

http://www.wildhorses4x4.com/product/Slip_Shaft_for_Stock_P_S

Slide your old one out, slide the new one in, and you should be good to go.
 
OP
OP
7

77bronk

Full Member
Joined
May 1, 2014
Messages
182
Loc.
Fort Worth, TX
Hot dam . That looks like the ticket right there . I didn't see that one on their site damit . Or I would have just bought that from the get go .
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
Man you guys rock on all the great information you have ..
.. I sure had issues putting my power steering to gather .. But I feel mine has some slack in this area now.
 
Top