• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Undercoating Questions

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
As I'm now replacing almost all the interior sheet metal, I have questions about undercoating

1). What should I use inside the wheel wells? I've seen some people use Rhino Liner, Lizard Skin, etc..

2) Is it do-able to undercoat panels before they are welded in, so as to not have to do it underneath the bronco, which is still on the frame?

3) What's undercoating does everyone suggest?

4) As it is still on the frame, what's the best way to apply it? I don't want undercoating sprayed everywhere underneath. That's what ButtStank did.

Thanks! - Jim
 

samamarshall

Full Member
Joined
Nov 3, 2008
Messages
244
A lot of fans of raptor liner here. Relatively inexpensive, DIY, and good results per most people. That's what I plan on doing interior and underside with. I believe most use Lizard Skin under it - I think it's more for heat/noise control.

Doubt you could apply it to panels, then weld near it. Not without touch up afterwards.

If everything is removed from the underside except body from frame, with a lot of prep/masking, you could probably get away wth spraying it. Won't be a fun job though!
 

NashBronco

Contributor
Sr. Member
Joined
May 9, 2013
Messages
398
Loc.
Flowood, MS
3) What's undercoating does everyone suggest?


Thanks! - Jim[/QUOTE]

I like Eastwood’s line of undercoatings. They have worked very well for me. I use their Rust Encapsulator products and it has worked well. I can’t attest to the long term performance yet but happy so far.
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
I used raptor on the inside of my tub. I forgot to weld up the pockets in the top of the rear panels (my choice for my build). I welded them up after the fact and it did mess up a bit of the raptor so I am going to have to fix it. I would make sure to have all the welding done if it were me.
I used 3M undercoating underneath my Bronco. I had purchased it before I saw the raptor liner. I am happy with the results of the 3M as well, but I would have shot raptor underneath if I had not already had the other. The raptor is smoother and is very easy to apply. I will say that the raptor is tough as nails, we had to beat a small dent out from inside the bed. We used a BFH and a 2x4 to do it and it never even scratched that raptor liner. Great stuff in my opinion!

Good luck with yours whatever you decide to use!
 

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
Is you goal heat and sound or more rust proofing? If you want both I'd do your encapsulator paint then both Lizadskin products then Raptor. Then if you don't want anything to stick to it, coat it with graphite paint. As to technique, lot's of cleaning then lots of masking and a lot of spraying. Took me many, many hours with the body on a rotisserie.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Bedliners are designed to harden, which will transfer noise when used as undercoating. True undercoating remains slightly soft, and it stays slightly greasy (especially in hot weather) so it's self-healing.

I've had excellent results from Mar-Hyde and Rustoleum rubberized undercoatings. These are both '93 Bronco frames:


(phone app link)



(phone app link)


No, I wouldn't apply anything before welding. You'll just create toxic smoke, and leave ash on the metal that will speed its corrosion.

But for the wheelwells, the most-effective fix is to build plastic liners, like most modern vehicles have:


(phone app link)
 

markw

Contributor
Bronco Guru
Joined
Sep 10, 2009
Messages
2,066
So Steve, what do you think of taking 50 gal plastic barrels and cutting sections. It's tough, already round and easy to work with. And seems about the right diameter for the wheel well.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I once did the Mohave trail and drove through a 1/2 mile of fresh cattle crap and wished I had wheel well liners.
 
OP
OP
ObscureMachine

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
Since I'm not doing a frame-off, spraying isn't really an option, not without a lot of work. I saw that Raptor makes a roll-on version. If everything is cleaned and prepped, would that be a good solution?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I use the 3m it works well even if the surface isn't the cleanest. Its easy to strip off if you need to later.
 

Nick163hunter

New Member
Joined
Mar 31, 2018
Messages
7
I would say POR-15. It is a bit expensive but it is definitely worth it. It isn't spray on you can apply it with a brush or even a roller. If you wanted to make it look like a show truck you can clear over the por-15 and it looks incredibly! Best of luck
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
I would say POR-15. It is a bit expensive but it is definitely worth it. It isn't spray on you can apply it with a brush or even a roller. If you wanted to make it look like a show truck you can clear over the por-15 and it looks incredibly! Best of luck

I use POR for the underbody coating as well as frame. I have a vehicle I did 18 years ago and still looks good. Easy to clean and repair/modify later down the road. Use top coat if you want it to look really good. You can brush it on as you go. Ken
 
OP
OP
ObscureMachine

ObscureMachine

Seatbelt Orifice Officer
Joined
Sep 28, 2006
Messages
3,998
Loc.
World Headquarters
I would say POR-15. It is a bit expensive but it is definitely worth it. It isn't spray on you can apply it with a brush or even a roller. If you wanted to make it look like a show truck you can clear over the por-15 and it looks incredibly! Best of luck

Thanks! I heard prep is a major deal with POR-15. I'm guessing it won't be a problem on all the new interior panels. Or, will they need major prep? Would roll-on Raptor be better or worse?
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
Prep is easy. Couple spray bottles and some water. I use a paint brush and sprayer for the metal prep, then hose off, let dry and apply. Ken
 
Top