• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Warn premium hub??.?

Audog

Jr. Member
Joined
Dec 12, 2011
Messages
83
Help please!!

With the Chevy disk conversion I do not use the small axle snap ring but do use the large outer snap ring, is that correct?

Also do I put the large spring back in before I install the new hubs?

Many thanks
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
No spring
You can omit the snap ring, some use a washer and bolt on the end of the axle if its threaded
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yes, you absolutely use the outer large snap-ring. If you don't, the hub won't stay in, so you'll know it was a mistake fairly quickly unless you don't bother to pull on the hub to check.

Yes, the inner smaller snap-ring can be deleted.

And like Ransil said, ABSOLUTELY NEVER put that original Spicer hub spring back in!
It says to remove all old stuff and put then new stuff in. That spring is part of the old stuff an only needed for the original hub design. The spring in the Warn (and virtually all other aftermarket) lockouts is internal to the inner assembly.

Paul
 

hotrod351

Full Member
Joined
Feb 28, 2013
Messages
175
did it a few months back, you sue a washer. the reason for the washer is that the axle doesnt stick out past enough to put the snap ring back on. all it does is keep the axlle from going back in. i have heard of cases where the person was able to reinstall the snap ring, but i couldnt and realized what the washer and bot where going to do once i did the swap.
 

admin

Administrator
Just your friendly, neighborhood webmaster...
Joined
Jan 1, 2001
Messages
38,897
Loc.
Phoenix, AZ
And like Ransil said, ABSOLUTELY NEVER put that original Spicer hub spring back in!
I'm curious. What's can go wrong if you do put the large spring back in?

I'm not saying you should. It's just that I ran my Warn Premiums for years with that big spring until I was told differently by someone here on the forums.

I don't recall having any problems engaging/disengaging them or unusual wear issues.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
I'm curious. What's can go wrong if you do put the large spring back in?

I'm not saying you should. It's just that I ran my Warn Premiums for years with that big spring until I was told differently by someone here on the forums.

I don't recall having any problems engaging/disengaging them or unusual wear issues.

I don't think anything will happen, I ran mine that way too for a long time until I realized it wasn't needed.
 

cballford

New Member
Joined
May 31, 2013
Messages
4
Loc.
Pensacola FL
nothing will happen for a while, but eventually the spring will wear down the lip on the inner part of the warn hub that keeps the snap ring in place holding the inner part of the hub together, then when you mash on the skinny pedal to pull your buddy's k-5 out of a stuck, you hear a loud pop, and that tire stops turning, just speaking hypothetically.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I've seen those installed that didn't have any problems either.
But the first several times I came across them, it was because a truck was in for service with regard to "funny noises" and "loose "stuff" up front" and other vague reasons.
When pulled apart, the inner hub section (aluminum) had been nicely machined down until, in some cases, they were literally worn through into the inner mechanism and no longer even remotely useable.

In theory, as long as everything is moving along in unison and correctly, the spring will just stay static against the back of the aluminum slug. But in practice, if anything catches on anything that's spinning in a different plane or at a different rate than the other stuff, instant lathe action!

It's pretty messy when it goes wrong. So my recommendation is to always remove it, like yesterday, and do not pass GO until you do it.

Lucky is good, but correct is safer.

Paul
 
Top