• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New to me 351W

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
The shop that did my short block gave me this balance sheet and said it would be needed if ever working on the rotating assembly.

I have no idea what these figures mean...curious if someone could explain.
 

Attachments

  • Balance info.pdf
    1.9 KB · Views: 56

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The shop that did my short block gave me this balance sheet and said it would be needed if ever working on the rotating assembly.

I have no idea what these figures mean...curious if someone could explain.

The numbers are weights of internal engine parts in grams. Pistons, rings, etc. should be self explanatory.
Rods are measured at each end seperatly
oil allowance is an educated guess on how much oil is stuck to the parts as the engine is running.
The 50% balance factor is half of the recricapating weight (piston, rings, pin, small end of the rod).
Add that to the weight of the big end of the rod and the bearings. Then double that since there are 2 rods on each journal.
Then then clamp that much weight onto the crankshaft and stick it on a very fancy balancer like what a tire shop uses to balance your tires. Then they do what they need to in order for it to spin without shaking.

Important note, your engine was balanced using a 50 oz-in flexplate and damper. You must use flexplate and damper from a late model 5.0 engine, not the early 302 or 351. Good thing is you can use an explorer front drive without having to rebalance the damper. Bad thing is you can't use your original flexplate/flywheel/damper parts. That may become an issue when putting all the parts on the engine and getting it in the rig.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
That may become an issue when putting all the parts on the engine and getting it in the rig.

Wasn't an issue at all. They gave me the balancer and flex plate they used. I swapped out the balancer with the one Wildhorses sells (50 oz) to get around the bolt pattern/pulley issues. Been running great since 2005.

Thanks for the explanation. I've never seen the balancing process and wasn't sure how they did it.
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
Assuming I have a deck height of 0.010 and I use 22cc dished pistons and a 60cc head chamber, I get a compression ratio of 9.81.

Would the Edelbrock Power Package Top End Kit, part number 2092 be a good fit for this plan? Summit doesn't give the specifics of the cam. The heads have 170cc intake runner volume and 60cc exhaust runner volume. http://store.summitracing.com/partdetail.asp?part=EDL-2092&autoview=sku
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
No comment on using a 22cc dished piston and 60cc head?

Can anyone recommend a 22cc piston? The Keith Black ones look pretty pricey.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Looks like it's all coming together for you. I know all about the snowballing...been there. How long until it roars to life?
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
Looks like it's all coming together for you. I know all about the snowballing...been there. How long until it roars to life?

Yeah, it's built off of your motor's spreadsheet.

Getting my Explorer Serpentine setup is basically all I'm waiting on. We don't have pick-n-pulls around here, so I'm waiting to stumble upon an Ex Serp for sale on the internet. If I found the front dress tomorrow, I could have it all together in 3 weeks. I'm putting an October 1st deadline on the project.

Immediately thereafter, I'll need to purchase a new rear driveshaft (mine is shot already, but I'm going to make it work for a couple of weeks.)

I've got my distributor, I just need to install it. It's getting a Duraspark.
 

broncbuster

Sr. Member
Joined
Jun 29, 2008
Messages
414
I've put mild marine cams in several off road motors. Something like a ski/wakeboard boat would use. They work real well if you have them ground with a little more (2 degrees) more advance. If you think about it a ski boat and off roader need the same type of power. Lots of torque down low and a decent midrange. The offroader just needs a little more advance. Many of the cam companies will custom grind for little to no extra $.
 

mountainview68

Sr. Member
Joined
Sep 5, 2004
Messages
598
Loc.
yet to be determined
Yeah, it's built off of your motor's spreadsheet.

Getting my Explorer Serpentine setup is basically all I'm waiting on. We don't have pick-n-pulls around here, so I'm waiting to stumble upon an Ex Serp for sale on the internet. If I found the front dress tomorrow, I could have it all together in 3 weeks. I'm putting an October 1st deadline on the project.

Immediately thereafter, I'll need to purchase a new rear driveshaft (mine is shot already, but I'm going to make it work for a couple of weeks.)

I've got my distributor, I just need to install it. It's getting a Duraspark.

Randy at driven autoparts stocks the explorer serp. you pay a little more money but you know its good stuff
 

66ALRIDE

Just BIP It!
Joined
May 9, 2005
Messages
1,785
Loc.
Dothan, AL
Give me a call Monday and remind me to check on the Explorer set up. I'll also get Jeff to check with some of his contacts too.
 

mountainview68

Sr. Member
Joined
Sep 5, 2004
Messages
598
Loc.
yet to be determined
Sure did. I was waiting until I got them in before bragging.

Dan was very friendly and he said that he would get them in the mail the day I ordered them. I hope to have them tomorrow or Monday.

Sweet.;D Don't forget to install the extreme motor mounts and move the proportioning valve forward before you get the engine in.
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
Bam! I've got to do a little clearancing to get them to fit. They are hitting my head bolts.

66ALRIDE is helping me get my Explorer serp stuff rounded up.

DSC01772.jpg
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
A Brazillion Dollars! (well, at least it feels that way)

Really about 4k. I hope you know, if my wife sees this thread she'll shoot me!
 
OP
OP
recoiljunky

recoiljunky

Bronco Guru
Joined
Jul 19, 2007
Messages
1,478
Loc.
Dothan, AL. USA
IT'S ALIVE!

After taking a whole lot more money and time than I had anticipated, my 398 Stroker is running.

I waited until 8:30 this morning, after the neighbors went to work and tried out the new motor. It fired up with little more than a bump of the starter. I let it roar at 2000 - 2500 rpm for 30 minutes. Temp stayed around 190, oil pressure was around 55 psi.

I couldn't help but blip the throttle a few times. This thing raps! I haven't got any exhaust on it yet besides the over-the-frame headers. LOUD!

Tomorrow I'm going to change the oil and filter and try to get some of the wiring straightened out. I'm going to be busy with work right now and won't have much time to work on this.

Those souped-up headers required me to ditch the stock clutch linkage and go with a hydraulic clutch set up. The clutch still needs bleeding and adjusting.

After I get done with that I'm going to hang some mufflers on it and turn the pipes out in front of the rear tires.

DSC01926.jpg


Older pic of my junk:
__sysMes.jpg
 
Top