• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

EFI EEC Mounting

Terkish

Sr. Member
Joined
Feb 22, 2008
Messages
414
I have finished up my EFI setup and all I have left is mounting the EEC up under the dash. What has everyone done here. Just looking for ideas.
Pictures would be great if anyone has some of there eec mounted.

Thanks ;D
 

bronco-billy-66

Bronco Guru
Joined
Sep 5, 2003
Messages
1,634
Loc.
Madison Mississippi
I made a bracket and pop rivited it to the bottom of the cowl right behind the speaker grill. I just ran a small bungee cord around it to hold it in.. I'll try to remember to take a pic when i'm in the shop tomorrow;D
 

av bronco

Bronco Guru
Joined
Mar 3, 2008
Messages
1,742
Loc.
Palmdale CA
This is a good question, Im about to do the same thing. I have the tuffy center console so Im thinking of sticking mine in the glove box.
 

IFLYHOOKS

Full Member
Joined
Dec 11, 2009
Messages
219
Loc.
Clarksville
I built a bracket "case" out of aluminum angle and secured it vertically above and to the right of the accelerator. I brought my wiring harness in behind the engine, so depending on where yours enters you may not be able to come over that far.

 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Mine is on passenger kick panel where it can be reached easily...
 

Attachments

  • ECU 001.jpg
    ECU 001.jpg
    154.7 KB · Views: 141
OP
OP
Terkish

Terkish

Sr. Member
Joined
Feb 22, 2008
Messages
414
Mine is on passenger kick panel where it can be reached easily...

I was thinking fo something like this. I kinda wanted it up higher out of sight thou.
My wireing comes in on the pass side. I'm thinking i should have mounted it while i had the heater box out up behind the glove box.
 
OP
OP
Terkish

Terkish

Sr. Member
Joined
Feb 22, 2008
Messages
414
I made a bracket and pop rivited it to the bottom of the cowl right behind the speaker grill. I just ran a small bungee cord around it to hold it in.. I'll try to remember to take a pic when i'm in the shop tomorrow;D


Something like this may work. I would like to see a pic if you remember. :)
 

fromme

Full Member
Joined
Nov 4, 2009
Messages
218
Loc.
Suffolk, VA
Mine is on passenger kick panel where it can be reached easily...

That's where I have mine, except you really want the harness connector pointing down instead of up. That way water can't run down the wiring and drip in to the computer. As far as mounting bracket, I don't use one. I used some really strong industrial velcro and I'm telling you it won't go anywhere.
 

Broncos n' VWs

Sr. Member
Joined
Nov 6, 2005
Messages
360
I mounted the ECU above the heater box. It's been there for over 4 years and no problems. Only downside is if I ever have to remove the ECU, the heater box has to come out also. (I have the RJM harness)
 

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
Attached mine under the dash with perforated plumbers strap and wingnuts.
 

fordtrucks4ever

Bronco Guru
Joined
Oct 8, 2006
Messages
1,280
Loc.
DFW
This has been covered many times. Do a search in the archive. There are good detailed descriptions on different ways of attaching it. I think Ford Fuel Injection also has some information. Check out the stock mounting brackets at your local bone yards. I know there are several that should work well.
 

Z Bronco

Bronco Guru
Joined
Mar 17, 2007
Messages
1,143
The explorer plastic holder is easier to get to than the mustang and I think it is the same.
 

76 bronco J

Bronco Guru
Joined
Oct 20, 2005
Messages
1,480
That's where I have mine, except you really want the harness connector pointing down instead of up. That way water can't run down the wiring and drip in to the computer. As far as mounting bracket, I don't use one. I used some really strong industrial velcro and I'm telling you it won't go anywhere.

>>> yeah.... the way jw747 mounted his computer is a major no no according to Ford... mounting with the connector on the bottom seems even more important in our barely sealed early broncos ..... mounting on it's side also doesn't seem ideal .... do you have ryans harness?? while comparing efi harnesses it seems RJMs would be better with a little more wire length for mounting the computer properly... here's a link to ford racings one-piece harness, page 9 is where it says to mount the computer with the connector on the bottom>> http://fordfuelinjection.com/files/M-12071-A50.pdf
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
Mine is mounted on its side, and I had water intrusion once, just had to bake it for an hour to get the water out, I don't think it matters how you mount it if it gets dripped on water will get in. best option is to fix your leaky bronco. I was using a zip lock bag to cover mine after the first leak.
 
Top