• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

full float drive flanges

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
I have a 9" axle with the Warn full float setup and the Warn premium hubs are junk! I have searched on this topic and I see that everyone has problems with these hubs. So, I would like to get drive flanges. Are these hubs or drive flanges the same as a front dana 60 or 44? The 60 and 44 flanges are the only ones I have seen for sale. Any recommendations on where I should get a good set of flanges?
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
wild horses had the drive flanges but I don't know if they still do. I got a set from 4 wheel pars for about $100. I know when I was researching for better hub options the specs looked like dana 60 hubs would fit but I never actually tried it.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I don't think he is wanting to spend the money on another full floater setup.

The Warn kit is based on the Dana 44 front hub. If you don't want to spend the $100 for aftermarket parts you can look for drive flanges off '73 to '79 full size american trucks with the NP203, fi no one has converted the solid drive flanges to lockouts. Another source is late 70's to early 80's full size Jeeps with Quadra track (full time) transfer case. Should only be a few bucks at a pick a part yard.
 

Oatmeal

Sr. Member
Joined
May 17, 2009
Messages
664
The Warn FF axles are 30 spline on the outer end so, drive slugs from the early full time trucks, which are 19(?) spline, aren't going to work. I too, had problems with the locking hubs on my FF'r......broke three of them. I believe that they're actually weaker than the 19 spline hubs because, the larger inner diameter of the 30 spline clutch hub, which is otherwise identicle to the 19 spline version, makes for a thinner wall thickness.......where it always broke?:? Oh yeah, I replaced those with Warn's drive slugs real quick. That was over 12 years ago---------Hans
 
OP
OP
68rockcrawler

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
I wish I had a junkyard around here where I could get a used set of flanges. It looks like it is going to cost me a minimum of $200 for a new set. Anybody seen them cheaper than the ones from Rockcrusher or Solid?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
The Warn FF axles are 30 spline on the outer end so, drive slugs from the early full time trucks, which are 19(?) spline, aren't going to work. I too, had problems with the locking hubs on my FF'r......broke three of them. I believe that they're actually weaker than the 19 spline hubs because, the larger inner diameter of the 30 spline clutch hub, which is otherwise identicle to the 19 spline version, makes for a thinner wall thickness.......where it always broke?:? Oh yeah, I replaced those with Warn's drive slugs real quick. That was over 12 years ago---------Hans

OK, I stand corrected. I guess what I have been told isn't always the truth (again). So the only fix really is go to Warn and hope they still have a set of drive slugs to sell you. Or find a set of 19 spline slugs and try to find a shop that can cut internal splines and work them into 30's. Better off buying a set.
 
OP
OP
68rockcrawler

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
The Warn FF axles are 30 spline on the outer end so, drive slugs from the early full time trucks, which are 19(?) spline, aren't going to work.

Hans - I checked my axles and they are 30 spline. There are less options out there for 30 spline flanges than for the 19 spline.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Like I said above. When I was looking thru a dana spec book the outer shaftfor the floater kit looked like dana 60 specs. I was gonna try some MM ultimate hubs for a d-60 but never got around to it. You may be able to find some dana 60 outers that will work. By the book it looked good but I never actually tried it.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
just throwing this out there, it sounds like money is tight and i dont know your current axle housing or brake set up or how strong the warn floater stuff is.
it is alot more, but for 800 you can have a brand new housing, tappered center and larger tubes, larger than d44 spindles welded in, larger bearings and drive plates that will never be an issue. also new axles and rotors. if youbuy rebuilt gm calipers i think you can have a complete floater rear and use your 3rd memeber for a 1000.
all parts he uses are very common.

http://9inchfloater.com/CompleteRrEnd/CmplteRrEnd_28_31.htm
 
OP
OP
68rockcrawler

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
Like I said above. When I was looking thru a dana spec book the outer shaftfor the floater kit looked like dana 60 specs. I was gonna try some MM ultimate hubs for a d-60 but never got around to it. You may be able to find some dana 60 outers that will work. By the book it looked good but I never actually tried it.

I was just looking at the dana 60 flanges and there are some out there that are alot cheaper ($120-150) but unfortunately they are 35 spline and mine are 30. I'm not sure how I would tell for sure if the 30 spline 60's would work unless I buy a set and try them on.

68ford - My whole axle is fine, I just need replacement hubs or flanges. Sounds like a good deal on a new full floater if I needed a new one. It doesn't look like their flanges will work on mine.
 

Oatmeal

Sr. Member
Joined
May 17, 2009
Messages
664
Currie http://www.currieenterprises.com/cestore/Product596.aspx?id=2198 seems to be the only ones that still have them available but, $300+?:eek: I'm glad I bought mine when I did, paid about $140! (IIRC) Maybe someone like Summers Brothers or Moser could machine you up a pair for cheaper?:? Then again, your hubs should have a lifetime warranty just keep replacing them when they break, I went through three of them but, it got kinda old or......Broncobowsher might have been headed in the right direction. Take some junkyard fulltime flanges and have them rebroached to 30 spline. Axle places like the afore mentioned Moser, Summers Brothers or Mark Williams could easily handle that--------Hans
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
A few years back the local 4wp had a bronco guy working there who was real cool. He gave me a dana spicer book with all the specs and part #'s for all the axles they made for all the different makes. Bearings, seals, axle diameters and spline counts. It's great for looking that stuff up.
 
OP
OP
68rockcrawler

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
A few years back the local 4wp had a bronco guy working there who was real cool. He gave me a dana spicer book with all the specs and part #'s for all the axles they made for all the different makes. Bearings, seals, axle diameters and spline counts. It's great for looking that stuff up.

So, do you still have this book? Could you find out if there was ever a factory 30 spline drive flange available? So, you were saying in your earlier post that the dimensions of the 30 spline 60's match up with the full floater 30 spline axles? So, what dimensions can you compare in that book (spline count, shaft diameter, hub diameter, etc)?
 
OP
OP
68rockcrawler

68rockcrawler

Bronco Guru
Joined
Sep 18, 2006
Messages
1,417
I have heard good things said about the Mile Marker supreme stainless steel hubs:
http://www.summitracing.com/parts/MMK-449SS/
These are 30 spline for a dana 60. $165 at Summit Racing
http://broncograveyard.com/bronco/i-11700-d60-d50-milemarker-supreme-stainless-steel-hubs.html
$130 at Bronco Graveyard. If these fit and are better than the Warn locking hubs this is sounding better than $200 flanges.

Is it worth trying these and hope they will work or should I just bite the bullet and spend $200 to get the flanges? Anybody regret have drive flanges?
 
Last edited:
Top