• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

NV3550/t-case install help

SoCal68Bronco

Sr. Member
Joined
May 23, 2007
Messages
387
Loc.
San Diego, CA.
I need a little help with the t-case adapter.

First, which holes do I use for the stock rotation. The directions are a little confusing.

Also, Im sure this is just me. But I can only get 4 out of the 6 holes to line up to the back of the tranny.
No matter which 4 holes I get to line up there are 2 that will not.
What I'm I doing wrong.

Thanks!
 

Attachments

  • IMG_3323.jpg
    IMG_3323.jpg
    104 KB · Views: 76

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
I just recently did this swap and I used the middle holes of the 3 pack and I had to rotate the bracket until they all lined up and they did eventually all line up.
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
We have been working with AA to get this kit to be easier for the installer. The following is from the "new" instructions.

Before you bolt the adapter to the Dana 20 transfer case, be sure that the orientation is correct.

The adapter has been marked “TOP”. To aid you in determining the correct grouping of bolt holes. Align the grouping to match the 1:00 transmission bolt hole position, and 11:00 bolt hole position. (1:00 is passenger side of transmission; 11:00 is driver’s side)

Next choose the desired rotation or clocking to soot your application. (stock rotation works great) WH You will need to determine this by placing the bolts in one of the three groupings the same for all six-bolt holes.

Hope that helps.

*Keep in mind; if you are clocking the Dana 20 up at the highest rotation for ground clearance, the shifter linkage may (will) WH need to be modified.


Hope that helps.


I need a little help with the t-case adapter.

First, which holes do I use for the stock rotation. The directions are a little confusing.

Also, Im sure this is just me. But I can only get 4 out of the 6 holes to line up to the back of the tranny.
No matter which 4 holes I get to line up there are 2 that will not.
What I'm I doing wrong.

Thanks!
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
i couldn't get my front yoke to clear the cross member in stock position for some reason, i ended up clocking it up 4º and using the center holes. i'm having no issues with drive line angles or linkages. my first trans did clear, this one doesn't. think the holes in the back of the trans case are drilled off a bit.
 
OP
OP
SoCal68Bronco

SoCal68Bronco

Sr. Member
Joined
May 23, 2007
Messages
387
Loc.
San Diego, CA.
"Before you bolt the adapter to the Dana 20 transfer case, be sure that the orientation is correct."

I think this is were my problem is...

Thanks for the help everyone!
I'm going to see what I can do today.
 
OP
OP
SoCal68Bronco

SoCal68Bronco

Sr. Member
Joined
May 23, 2007
Messages
387
Loc.
San Diego, CA.
Thought I would update:

T-Case is finally on. The orientation was not correct.

Tip for future NV3550 installers:
Align the adapter to the back of the transmission FIRST. Then you can bolt up the T-case (Middle holes).

Again thanks for all your help!
 
Top