• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tbird EEC programming

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
Does anyone have any information on reprogramming a Tbird EEC IV computer.
I know the Mustangs are well supported but what about the Birds?
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
as long as you are using it with everything else off the same vehicle should not be an issue.

BTW I have a computer & maf housing from a bird for sale cheap.. email me if interested.
 
OP
OP
Pedestrian

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
as long as you are using it with everything else off the same vehicle should not be an issue.

BTW I have a computer & maf housing from a bird for sale cheap.. email me if interested.

Well that's kinda the issue. I am using the computer and harness off the Bird, Explorer intake, throttle body, and MAF, all on an OMC marine GT40 Cobra motor, with a high revving cam.
Runs well, but under hard accel/ drag race, it has a BAD flat spot in the midrange.
I am willing to have it dyno tuned and a chip programmed, but am wondering if I should just change over to the Mustang ECM if the Bird isn't supported
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
What is the box code?
Does the aftermarket DIY tuners list it as a supported code?
That is a lot more accurate then just asking about a generic application.
 
OP
OP
Pedestrian

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
give the guys at AMP performance a call they can probably burn a chip for you

Thanks Jay, I'll give them a shout.

I checked out the Tweecer site and wasn't able to get a comfirmation on whether the Tbird was supported.

Quarterhorse site states it will support all EEC-IV computers.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
If you want a tune that actually matches your parts and not a brown paper bag tune, There is always Arizona Dyno Chip. Still need to know the box code to tune any of them. You will need an EEC-IV with a J3 service port or none of them will tune. http://www.fordfuelinjection.com/?p=17
 
OP
OP
Pedestrian

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
Pretty sure I have the P3M computer. I do know it has a J3 port.

Thanks 744x4, I appreciate the link.
 

broncomitch

Bronco Guru
Joined
Jan 17, 2008
Messages
2,384
Loc.
west jordan, utah
Thanks Jay, I'll give them a shout.

I checked out the Tweecer site and wasn't able to get a comfirmation on whether the Tbird was supported.

Quarterhorse site states it will support all EEC-IV computers.

have you found anything out?

i would love to get my idle smoother and have it set up for maybe a bigger injector swap.
 

vertex

Full Member
Joined
Jan 4, 2006
Messages
261
Loc.
Oregon City
I have the same Thunderbird EFI swap and found no support for the P3M computer. I ran across an article about converting the Thunderbird EFI to run on a 94 / 95 Mustang computer. I converted my Thunderbird EFI system to run on a 95 Mustang 5 speed computer, the code for the 5 speed computer is T4M0. I then bought a quarterhorse programmer with the binary editor and EEC analyzer. There is a lot of support for the CBAZA strategy. I decided to go this route because I will soon have a 347 stroker installed so I wanted the flexibility to program the computer myself.
 
OP
OP
Pedestrian

Pedestrian

Bronco Missionary
Joined
Sep 10, 2008
Messages
2,299
Vertex, thanks for the feedback. I have decided to swap the Tbird stuff into my crawler project and convert my son's street project to Mustang A9 for better support.
 
Top