• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wobbly Wheel Update - New problem with spindle.

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
My driver front wheel is wobbling and would like some ideas on how to troubleshoot this.

So far, I have swapped wheels with one of the backs that was driving straight, same issue.

I then put new wheel bearings in, same issue.

What else could I try? Only two things I can think of now is ball joints or a warped hub\roter hosuing.

Thoughts?
 
Last edited:

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
It sounds like a hub...worn ball-joints can cause some funky symptoms, but "wobbly" would be the first adjective to pop into my mind.

How much "wobble" are you seeing? I'd probably pull the tire/wheel and spin the hub/rotor and look for runnout with my bare eyes to see what I see. If you have a dial indicator and a magnetic base, that would tell you down to the thousandths of an inch what your total indicated axial runnout is. Have you hit any curbs lately?
 

bluemonday

Sr. Member
Joined
Mar 16, 2010
Messages
690
Loc.
South Louisiana
Ball joint / King Pin. My wheel would move top to bottom. Jack the drivers side up, pull on the top of the tire and then on the bottom of tire to rule my idea out.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Ball joint / King Pin. My wheel would move top to bottom. Jack the drivers side up, pull on the top of the tire and then on the bottom of tire to rule my idea out.

Good point...I was assuming D44, not D30. Could be the KP's which are well known for "death wobble".
 
OP
OP
Izzy

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
The wobble is in\out, not top to bottom. It is a d44 so is the king pin still a concern?

I didn't think about using a dial indicator. I will try that now.

Also, when I did have the tire off the ground, I tried moving it back and forth by hand but everything felt good and tight. After replacing the wheel bearings, it drives better by feel but when I watch the wheel\tire on the road, it still wobbles.

I'll let you know the results of the dial indicator test.

Thanks guys.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
pull the wheel hubs and swap the whole assembly from side to side. If the wobble follows the swap then you know its the hub - rotor/drum assembly.
 

gearida

Bronco Guru
Joined
Jun 8, 2007
Messages
1,428
Loc.
Newburgh, IN
Steering box? Or tie rods, I am fairly sure you have looked into the bushings of drag link too. Just a thought.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
The wobble is in\out, not top to bottom. It is a d44 so is the king pin still a concern?

I didn't think about using a dial indicator. I will try that now.

Also, when I did have the tire off the ground, I tried moving it back and forth by hand but everything felt good and tight. After replacing the wheel bearings, it drives better by feel but when I watch the wheel\tire on the road, it still wobbles.

I'll let you know the results of the dial indicator test.

Thanks guys.

D44 has ball joints, so no KPs to worry about.

By in/out, do you mean in the steering directions? That would point towards steering components and/or track bar bushings like gearida pointed out. Drag link ends, tie-rod ends, steering box, etc. Frame may have issues where the box mounts because it may be the whole axle moving, not just the wheel/tire.
 
OP
OP
Izzy

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
But the passenger side doesn't wobble at all. Been out working on other parts of the Bronco but will do the dial indicator test tonight.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
You ruled out the wheels by swapping them around.
I presume you can put it on a jackstand and spin it and see the wobble, rule out the knuckle is moving.
Only thing left is the hub itself. Swap rotors side to side to confirm. After that I am at a loss.
 
OP
OP
Izzy

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
Update:

I did the dial indicator test and there is a wobble in the hub. I have a hub on my 76 that I can swap with it but I ran into an issue getting the wobbly hub off, the washer that goes between the lock nuts shifted into the threads thus scaring the spindle threads.

This rig has the chevy disc swap while my 76 has the stock disc brakes so the spindles do not match. Where do I get another spindle to replace the one I have?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The spindle is a '73-76 Chevy half ton. The spindle bolt holes on the red beast are drilled for 7/16 bolts.
But I think you are going too deep. replace/swap the spinning parts (hub/rotor) and see if that fixes it. The spindle is fixed to the knuckle, there is nothing with the spindle itself that can cause a wheel to wobble.

Is the wobble matched to wheel speed? that would indicate something outside of the wheelbearings is the issue as the knuckle and spindle are holding true.
If it is a random wobble (flopping about) it would be something in from the knuckle (Ball joints, tie rod)
 
OP
OP
Izzy

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
I replaced the hub with one off my 76 this weekend and it did in fact fix the problem. The only reason I am now concerned about the spindle is because the lock ring that goes between the lock nuts spun into the threads thus destroying that portion of the thread.

I actually had to cut the hub off just so I could get to the lock nuts and get them off. I went ahead and put it back together as is but I'm worried the next time I need to service them, the lock ring is going to be spun into the threads again making it hard to get off yet again.

For now it's fine but I may need to replace it on the next servicing.
 
Top