• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Cooling Guru's, help needed. EFI 5.0 - SOLVED!

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
I'm having a cooling issue with my 5.0 EFI. It's currently in my Mustang, to be moved to the Bronco. I've been chasing this for a year, and want to solve the problem before pulling it.

Car is set up with Shorty headers, K&N filter, New fuel pump, lines, filter. Cooling system is as follows: New 1971 351 three core radiator (non ac type) 93 3.8 Thunderbird clutch fan, 71 Mustang fan shroud, 73 Maverick 302 lower radiator hose (with spring), 89 Ranger 2.9L lower radiator hose (as the upper.) This setup works well on an Arizona car, and many others, that's set up the same way.

The problem:
At highway speeds, 2,800 RPM, the temp rises to 225 deg (and growing), at 1900 RPM the temp will go down and stand at 210 deg. I can replicate the issue holding at 70 MPH while shifting in & out of overdrive. in Drive, temp rises (225+), in overdrive, it drops (210 ish).


I have a $30 mechanical gauge but the electric gauge showed the same pattern. I have replaced the clutch fan, installed a coolant tank, tried 180, 190 & 195 deg t-stats, 13 & 16 lb radiator caps. The radiator is new, hoses are good, no sign of antifreeze or oil contamination, no sign of white smoke, or smell of anti-freeze in the exhaust, head gaskets are on properly, proper new reverse rotation water pump. All pulley's are stock size, belt is new. Water flows across radiator once stat opens, Head gaskets were positioned properly, engine was remanufactured, 60K miles now.

Please share your experiences with similar driving conditions. I really need to get this right, and it's driving me mad.
 
Last edited:

Rox Crusher

Bronco Guru
Joined
Dec 13, 2008
Messages
2,830
You don't say what year Mustanf but it sounds like you swapped this 5.0 into an older horse ?

How is the fan penetration into the shroud ? 2/3 of fan blade should be inside the shroud.

Any chance the outside of the radiator has become plugged / blocked off somehow ?

What about engine timing ?

is the tranny on a cooler ?
 

TwoDalesDad

Bronco Guru
Joined
Jul 19, 2011
Messages
1,515
Whats your he's ratio?..... To me 2800 RPMs are the problem.....you need an overdrive....secondly what about a high volume water pump.....along with a water wetting agent...should drop your temps by 30 degrees....good luck....stay cool.....really chill
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
It's currently in my 67 Mustang, fan penetration is right on, and it's a new radiator. The car was completed last spring, and I've been chasing the problem since. The trans is cooled thru the radiator, but again, this same setup is keeping cool in Arizona Heat on another rig. I tried timing at 14, 12 and 10 degrees, no change in behavior. Also running a 50/50 coolant mix

2800 rpm's is not a problem, and as mentioned in the post, I have an AOD.

Really trying to find someone who has experienced this behavior before. Water wetters and high volume water pumps are not always the best solution to cooling problems. They are often band aids.
 

Rox Crusher

Bronco Guru
Joined
Dec 13, 2008
Messages
2,830
Ok, what is the history of the 5.0 itself ?

Has it been bored too far during a rebuild ?
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Ok, what is the history of the 5.0 itself ?

Has it been bored too far during a rebuild ?


I can't say for sure. It was remanufactured, but I'm uncertain on the bore. Is there a point where over boring the block could cause this? I'm guessing it's no more than .060
 

Rox Crusher

Bronco Guru
Joined
Dec 13, 2008
Messages
2,830
I don't know specifically about 5.0 reborn limitations but I once tried to make a 428 using a 390 and the motor ran too hot because the cylinder walls were too thin.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I know a guy who has a beautiful 55 Chebby restomod. Put it all together with the best of everything, including a brand new BeCool aluminum radiator to help cool his 383. Had cooling issues at speed from the day he started driving it. Idles fine but heats up like yours when cruising. He did all the normal fixes: High flow water pump, pulley size changes, water wetter, etc.

Finally, after overheating the 383 and warping a head, he pulled the radiator out and took it to a shop. It took the guy at the shop 2 minutes to find the problem. The radiator had been overpressured (presumably at the factory) and the tubes expanded, not allowing enough air flow through the radiator to cool with the bigger heat load of cruising.

A new (not BeCool) radiator resolved all his cooling issues.
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
I know a guy who has a beautiful 55 Chebby restomod. Put it all together with the best of everything, including a brand new BeCool aluminum radiator to help cool his 383. Had cooling issues at speed from the day he started driving it. Idles fine but heats up like yours when cruising. He did all the normal fixes: High flow water pump, pulley size changes, water wetter, etc.

Finally, after overheating the 383 and warping a head, he pulled the radiator out and took it to a shop. It took the guy at the shop 2 minutes to find the problem. The radiator had been overpressured (presumably at the factory) and the tubes expanded, not allowing enough air flow through the radiator to cool with the bigger heat load of cruising.

A new (not BeCool) radiator resolved all his cooling issues.

I just brought the radiator to a specialist. He certified that it's flowing right. The radiator only has 8 fins per inch, and in his opinion, that is the problem. He gave me a few tests to run, but said it should have at least 12 fins per inch. Please keep the info flowing, I'll update any new info. Thanks!
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
I can't say for sure. It was remanufactured, but I'm uncertain on the bore. Is there a point where over boring the block could cause this? I'm guessing it's no more than .060

anything over .030 you can run into over heating issues
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I know a guy who has a beautiful 55 Chebby restomod. Put it all together with the best of everything, including a brand new BeCool aluminum radiator to help cool his 383. Had cooling issues at speed from the day he started driving it. Idles fine but heats up like yours when cruising. He did all the normal fixes: High flow water pump, pulley size changes, water wetter, etc.

Finally, after overheating the 383 and warping a head, he pulled the radiator out and took it to a shop. It took the guy at the shop 2 minutes to find the problem. The radiator had been overpressured (presumably at the factory) and the tubes expanded, not allowing enough air flow through the radiator to cool with the bigger heat load of cruising.

A new (not BeCool) radiator resolved all his cooling issues.

Usually it is the other way around. When the head gasket goes you are suddenly dumping engine compression into the cooling system in large volumes. The ballooned tubes were the result of the head gasket failing, not the cause. It is hard to determine what was the cause and what was an effect. Unless you find the ballooned tubes before you blow the head gasket, the radiator is simply a casuality of the head gasket failure.

Back to the original post...
So it is a high RPM gradual overheat condition. It sounds like a lack of radiator capacity to me. The only other thing I would look at is the fan itself. the blades have a curve to them. they scoop the air. If you flip a fan blade over it will initially still look correct, but it will swat at the air. The leading edge should be parallel to the radiator and the trailing edge parallel to the engine. If it is flipped it will make plenty of noise but not move that much air. It may even be blocking the airflow you need. Hence why you can stay cool on the highway at lower RPM but with the same power level at a higher RPM it runs warm. And the backwards fan will probably move enough air at idle to stay cool there as well, just not as much as it could, but enough.
The last idea is some wierd waterpump issue where it is cavatating at higher RPMs, but I doubt that. I don't think you are turning enough RPM for it to be an issue.
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
So it is a high RPM gradual overheat condition. It sounds like a lack of radiator capacity to me. The only other thing I would look at is the fan itself. the blades have a curve to them. they scoop the air. If you flip a fan blade over it will initially still look correct, but it will swat at the air. The leading edge should be parallel to the radiator and the trailing edge parallel to the engine. If it is flipped it will make plenty of noise but not move that much air. It may even be blocking the airflow you need. Hence why you can stay cool on the highway at lower RPM but with the same power level at a higher RPM it runs warm. And the backwards fan will probably move enough air at idle to stay cool there as well, just not as much as it could, but enough.
The last idea is some wierd waterpump issue where it is cavatating at higher RPMs, but I doubt that. I don't think you are turning enough RPM for it to be an issue.
I put everything together, after verifying I have the right water pump. I ran it up to 225 with cardboard over the radiator. After removing the cardboard it dropped slowly at idle. A little garden hose water to the front of the radiator, and it plummeted. I hope this is heat transfer issue on a crappy radiator.
 

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Start the engine up, take a piece of paper and put it in front of the radiator. If the paper doesn't get sucked up, you found your problem.

I say this because my dad was having the exact same problem with one of his cars. It turned out the flex fan he ordered was misboxed. It was a reverse rotation on a std pulley causing the exact problems you describe.

I try to start at the simple idiot problems first, then work my way to the mind twisting ones.
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Start the engine up, take a piece of paper and put it in front of the radiator. If the paper doesn't get sucked up, you found your problem.

I say this because my dad was having the exact same problem with one of his cars. It turned out the flex fan he ordered was misboxed. It was a reverse rotation on a std pulley causing the exact problems you describe.

I try to start at the simple idiot problems first, then work my way to the mind twisting ones.
~Not the issue~
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
would bet your clutch fan is malfunctioning. they're known for this and should be used for boat anchors only. try my earlier suggestion just for grins.
 
OP
OP
B

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
would bet your clutch fan is malfunctioning. they're known for this and should be used for boat anchors only. try my earlier suggestion just for grins.
see original post..... the clutch fan is fine, replaced it to be sure, no change.
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
see original post..... the clutch fan is fine, replaced it to be sure, no change.

most everything that's been suggested here is either functioning like it should or is not broken. so it would seem there's not a problem since everything is working right.
 
Top