• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

best performing engine for a bronco?

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Oh and I think I read somewhere about 351s eating up C4s or 9" rears....true? I probably need to rebuild both of these on mine anyway but I'd hate to do that and then just destroy them again with the beefier engine.

Well I have a Windsor with a c-4 and 9". I have been running them for over 20 years. I guess I don't have a lead foot. But I drove it set up this way through out my twenty's. I definitely flogged it pretty hard for awhile there. I am much easier on it now but still no problems.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I admit- I dont know much about the 351 heads...

I have a good, running '96 explorer 5.0 that I have torn down to eventually replace the 89 Gran Marquis 5.0 the PO installed that is making noise. Although the 96 motor is in very good shape... I can't leave well enough alone and have thought about stroking it. If the GT40 heads are good enough for the 351... What's wrong with using them on a 347? Are there better heads- Yup- for both motors... But if they breathe enough for the 351, they should do just as well with a 347.

I guess I need to gain some understanding of fundamental performance motor design. Even on the Horsepower TV show today- they showed how a better breathing 351C head (2V vs 4V on the C motor) was not better for a street motor, dropping both torque an HP. Larger heads typically move the power up in the RPM range- exactly the oppositions of what I am looking for in my street Bronco on 37s.

I can see where a 351 as a base would be lower cost- no bore and stroke changes unless the motor needs a crank and bore cleanup. You are already starting with 350+ cubes... BUT I hear of alot of cooling issues with the bigger block. May be a bad perception on my part- but I still hear and see it. Not to mention a few other minor fitment issues.

What I really want to know- can you build a 302 based stroker and design it around the needs of a Bronco owner with oversize tires... and what is that formula? What will a 347 with GT40 heads do and what kind of cam should you throw in it to maximize torque and HP in a driveable RPM range (1500-5000rpm??)??

Todd

Windsor's running hot(?).....Yea mine did many years ago but today there are alot of fixes for that.

My 351W never gets above say....170°F now.
See below.

4 core JD rad.
Flowkooler wp
Small wp and big crank pulley from BC
160° thermostat
Plastic flex fan from Summit custom clearanced for my a/c compressor
Finally a good carb & timing adjustment.
The BC pulleys were the last part installed. Seemed to be that last little bit I needed.
 

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
Windsor's running hot(?).....Yea mine did many years ago but today there are alot of fixes for that.

My 351W never gets above say....170°F now.
See below.

4 core JD rad.
Flowkooler wp
Small wp and big crank pulley from BC
160° thermostat
Plastic flex fan from Summit custom clearanced for my a/c compressor
Finally a good carb & timing adjustment.
The BC pulleys were the last part installed. Seemed to be that last little bit I needed.

Great point- with an added cost the 351 can stay cool...

Adding cubes to the 302 and additional friction from the stroker will add some heat, but I have no issues with heat on the efi 5.0 I have now, so I should be able to use the exact setup on a 347...

I a, just looking to see if there is a good 347 setup to run targeted at something other than a Mustang. The easy answer always seems to be- start with a 351w. I guess I am just a glutton for punishment, but I like the idea of the 347.

Todd
 

svobronco

Contributor
Sr. Member
Joined
May 31, 2011
Messages
350
Get a 351 and build a 427 stroker! Nice thread hy-jack by the way.....:p
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Any drawbacks on the swap to 351? I guess size and fuel efficiency are the only real negatives right? I'm not TOO hung up on efficiency but if we're talking the difference between 15MPG on the 302 and 5MPG on the 351 maybe i would be.

I've heard they're a bit tighter fit. Any issues with specific headers, 4x4x2 box, etc.?

Only other consideration is cost I guess. How much did the 351W at the junkyard run you? Should it cost about the same to rebuild once I own the block?

Sorry for all the questions! I really do try to research and read up on all of this myself, but sometimes it's easier to just run with a train of thought! Thanks guys!


If you drive it nice people have reported actually getting better MPG's due to the motor having to work less or running a low RPM. Headers should fit, motor isn't close to the power steering so it should be fine.

I paid $100 for the short block I got from the yard and another $100 for the cylinder heads off an Explorer. I left the factory truck cam in there and it pulls like a freight train with 37's and 4.11's in 2nd high range. Plenty for me I'm doing, plenty for damn near anything.


Great point- with an added cost the 351 can stay cool...

Adding cubes to the 302 and additional friction from the stroker will add some heat, but I have no issues with heat on the efi 5.0 I have now, so I should be able to use the exact setup on a 347...

I a, just looking to see if there is a good 347 setup to run targeted at something other than a Mustang. The easy answer always seems to be- start with a 351w. I guess I am just a glutton for punishment, but I like the idea of the 347.

Todd

I'm running a junkyard 351w, junkyard heads, junkyard explorer serpentine, junkyard 4.0 radiator, 5.0 fan, original shroud and no matter how hard I push it I couldn't get it over 200*F. I just cant see spending the money ($700+) on a stroker kit just to fall short of a factory option.

Ask yourself this - what can a 347 do that a 351w cannot? (in how you are going to use it in an EB)
 
Top