• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

4R70W calibration file

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Does anyone have a custom 4R70W calibration file they would care to share? Just looking to not reinvent the wheel.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I have had a couple, not sure I still have that computer anymore. One was neat in that at idle it was in 2nd gear to reduce creep at traffic lights but when you got on the throttle it downshifted into 1st. Never felt the shaft and it worked perfect. But the upper end shift points might be a bit rich for a lot of you. I'll see if I can find that file.
 

Kyle.malone

Bronco Guru
Joined
Mar 9, 2006
Messages
3,077
Loc.
Norman, OK
I haven't driven mine enough to tune it how I like. Still a work in progress. Even though my rig has been fininshed since last year (OBCR) it has gone through many upgrades and still only have 300 miles on it since frame off. It's very easy to keep two programs as there are two tabs on the program to write to. Just keep one a safe setting and the other your test forum.
 

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
If your using the optishift just use one of the stock files to get you going. start with the mild one. dont' know what one i put on it the other day but its not a mild one it put the wide open shits out to almost 6k. opened my eyes up real quick.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I can't find the files. The stoped in 2nd is easy enough to make. Take your standard file and move the 1-2 upshift and down shift points to 0 MPH for the first ~20% of throttle. Leave the rest alone.

You can make a dyno profile by moving all the 1-2 and 2-3 shift points to 0 MPH. Don't even worry about 3-4, just run the dyno with OD off. If you are real slick you can also lock the convertor to get real torque curves from idle to redline without convertor induced errors.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I am thinking about making my alternate program for off road / rock crawling. Can anyone suggest what things I should change. I know most of it will just be 1st gear stuff but what about the converter?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Thanks for looking. Are you still running a 4R?

I am between broncos right now. I am looking for the correct bronco to start the next project. Have pactience, going to hold out until the right one becomes available to start on. Going stick. More of a fun toy, not so much of something for rocks. Little more outside the box of conventional builds.

As for programming an offroad table, drive it, see hat it does wrong, adjust. For me the 1-2 shift at 3MPH was very annoying so I started in 2nd gear. When I needed 1st I just moved the shifter into 1st and it would go there and hold it. I also put a manual torque convertor over ride button on the floor. under where the clutch pedal was. I could mash it and lock the convertor for long hill climbs or when I wanted to show that i could idle over stuff in an automatic.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I feel like I need a whole cluster of switches for this thing.

Converter
Up/ down shift
Alternate program
OD on/ off

I love the flexibility but need to find an inexpensive and efficient way to utilize them without making a mess of my cab.

Thanks again.

Sent from my Droid using Tapatalk 2
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Convertor should only be momentary.
OD off can be either momentary or on/off
Shift table is on/off.

When I did mine there were only 2 visable switches when done. OD off and table switch.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I am between broncos right now. I am looking for the correct bronco to start the next project. Have pactience, going to hold out until the right one becomes available to start on. Going stick. More of a fun toy, not so much of something for rocks. Little more outside the box of conventional builds.

As for programming an offroad table, drive it, see hat it does wrong, adjust. For me the 1-2 shift at 3MPH was very annoying so I started in 2nd gear. When I needed 1st I just moved the shifter into 1st and it would go there and hold it. I also put a manual torque convertor over ride button on the floor. under where the clutch pedal was. I could mash it and lock the convertor for long hill climbs or when I wanted to show that i could idle over stuff in an automatic.

Were you running the Opti-Shift? I don't see an option to have a button to lock the converter in the accessory section of the harness.
 

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
There is no wirring diagram for it. i believe you have to momentarly ground the brown wire in the harness to lock the converter.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Were you running the Opti-Shift? I don't see an option to have a button to lock the converter in the accessory section of the harness.

It isn't in the harness. You get a momentary contact button. One side goes to ground, the other gets tapped into the convertor clutch wire. It is not in the instructions. this is a custom modification beyond the normal install.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
So the brown wire... momentary ground on / off???

Untitled-5.jpg
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Correct

Ground the brown wire (in the diagram above) and the convertor will lock.
Won't lock in reverse. Some valve bodies may not lock in 1st gear.

Remove the ground and it will go back to computer controlled logic.
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Does anyone have a calibration file to prevent downshifting and force converter to stay locked (without switch). And keep OD off so i can run this thing on a dyno without having to reinvent the wheel?

Sent from my Droid using Tapatalk 2
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Disregard. I saw in a previous post where Broncobowsher explained what to do for a Dyno file.

I set everything for 1-2 and 2-3 down to 0 across the board and left 3-4 alone with plans to either let the program lock the converter up at 20MPH since that was as low as the program would let me go. I assume it has to do with where the 3-4 curve is set? I guess I could install a switch instead and try to lock it up lower. Also have to disable the O/D.

Anyway, I think Blazinchuck is going to take my rig to the Dyno on Saturday so I have to get this file finished up and emailed to him and walk him through uploading the file and maybe smooze him into hooking up an O/D switch for the Dyno. ;)
 

DanWheeler

Bronco Guru
Joined
Nov 8, 2005
Messages
2,572
Loc.
Kirkland, WA
I feel like I need a whole cluster of switches for this thing.

Converter
Up/ down shift
Alternate program
OD on/ off

yup.

IMG_9772-M.jpg


With regards to the tuning - I'd recommend using a laptop with a USB->Serial adapter (unless you are using the USB optishift) and taking it out for a drive and do your tuning on the road.

Start with the default file,

1. Go 0 to 60 - note what you don't like
2. Tweak your settings
3. Save/Upload (you don't even need to turn the engine off)
4. Repeat until you like it

I've not found any reason for an offroad 2nd shift table. I'm either crawling in 4-low in first or 2nd or driving around normally in 2 or 4-hi.

When you go into 4-low, everything is going to get screwed up anyway because your output shaft sensor will be out of whack. (it will think you are going twice as fast as you are depending on your t-case ratio)
 
Top