• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Best C4 core to look for?

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
My C4 was rebuilt by a knucklehead who puts shift kits in everything without being asked to.
This proved to be a bad idea on EBs. Even on light accelerations it chirps the tires. The two auto Broncos I bought new had shifts that were plenty firm from the factory.
I know that part of the shift kit install was drilling one or more holes in the steel plate in the valve body. I did it on two C6s. To go back to a factory type valve body I'll have to take one from a core C4. How do I ID a late truck model in pile of transmissions.
There were an endless number of valve body specs so the late truck seams the best source. The bigger trucks with small blocks had C6s so I'm thinking '70s F150s.
Is it possible that pan fill types with a separate bell housing would all work? How about C5s?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
First, you can shrink the holes in the separater plate a little. Hammer a ball bearing or small punch around both sides of the plate.

2wd F100-F250 and vans had C4's with either a 6 cyl or 302 up until '81. They were pan-fill and had a shift lever very similar to a Bronco.

C5's had some good parts but the valve body is not one of them.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Do you need the whole transmission or just an original valve body?
May be a dumb question, have have you tried a Ford dealer and see if they can get a stock seperator plate? Sometimes I am amazed what you can still get from Ford.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
call one of the transmission part houses, they can hook you up, however they will probably want to sell you just a valve body, not a plate..
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Dont you just need any 1970 or newer C-4 valve body from a c4 running a 302. I assume you are looking for a stock seperator plate and the proper balls and springs inside the valve body. Thats assuming you started with a stock Bronco c-4. Unbolt the body and install in the Bronco with the right Bronco filter.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The transmission shops tell me unmolested IE no shift kit valve bodies are hard for them to find and they deal with tranny parts houses daily. The C5 was recommended as a source of all parts except the valve body, bell housing, and torque converter. They say the internal passages are better. The junk yards are reluctant to allow me to remove a pan and valve body alone but cash speaks loudly in their world.
The shift kit has several sliding valves and springs that are hard to tell from the Ford parts when lying side by side. So the steel plate sandwiched between two aluminum castings isn't the only part effected with a shift kit. It's just the easiest to ID as modified.
So if I can't run around tearing a pile of C4s apart, it would help to know what to look for in C4s on the ground. The pan fill and bolt on bell housing are part of a Bronco C4 and supposedly features of truck applications. As said tho, I don't want a valve body from a C5 and they look much the same.
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Should be able to find one at almost any u-pull-it and cheap. What shift kit did they use? There are different levels and a stage one kit will make the transmission last longer. Yes it will firm up the shifts a little but the higher pressure does make them last longer by decreasing the load on the transmission. Sorry my 2 cents.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
I'm going to pile on that the upulls in my area don't let you pull a c4 apart, if they have one, which they don't.
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
the ones around here have let me and I have found at least one in every yard I've gone to
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
There are 3 U Pull-It type yards in Tucson and I can give you a tour of them. I just found a valve body at one of the tranny shops that has '73 casting #s. All the parts match those pictured in my '77 Ford truck shop manual and the separator plate is not drilled. I'm optimistic about this one. I know a Transgo shift kit was used and I have an extra with instructions. I found that the install only enlarges a hole with an included drill bit.
As you can see I'm not anti shift kit but I've found that the Bronco doesn't need one. In Az. an auto trans doesn't wear out, the soft parts get hard first. It's the heat. Witch reminds me. Has anyone changed the cooling lines to 3/8"?
 

wheelsblank27

Sr. Member
Joined
Oct 20, 2012
Messages
370
Loc.
805
I doing a swap to c4 in my 68' the only one I found locally was a case filled 70's which is what I was told to get (at least the 70's pat) and it was from a car probly maverick or pinto or somethin but the guy I bought it from was putting in a v8 so he had a brand new v8 valve body and forward pump and c5 clutches that he was gonna use in his build. Only one problem he didnt leave any tranny oil in it soothe Simpson gear train was rusted bad. Te planetarydoesnt even rotate.... Doh. So I luckily Am taking a class at the city college and they are phasing out a c4 so I can salvage parts for mine. Anyways do yu know anything about the difference between flex plate teeth differences & the matching bellhousing mine has a 157 tooth bell housing size and need to know if that will work in my bronco with a 289? The other option is looking for a 164 tooth flex and bell....
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
There are 3 U Pull-It type yards in Tucson and I can give you a tour of them. I just found a valve body at one of the tranny shops that has '73 casting #s. All the parts match those pictured in my '77 Ford truck shop manual and the separator plate is not drilled. I'm optimistic about this one. I know a Transgo shift kit was used and I have an extra with instructions. I found that the install only enlarges a hole with an included drill bit.
As you can see I'm not anti shift kit but I've found that the Bronco doesn't need one. In Az. an auto trans doesn't wear out, the soft parts get hard first. It's the heat. Witch reminds me. Has anyone changed the cooling lines to 3/8"?

The bit included with the transgo kit is .110". I've gotten less aggressive shifting results by drilling to .80"-.90" and leaving the cutback valve stock (no orange spring).

Running 3/8" cooling lines won't help. The stock C4 rear return passage is only about 9/64". I enlarge that to 3/16".
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Anyways do yu know anything about the difference between flex plate teeth differences & the matching bellhousing mine has a 157 tooth bell housing size and need to know if that will work in my bronco with a 289? The other option is looking for a 164 tooth flex and bell....

The flexplate size needs to be matched to the bellhousing. A 164 tooth flexplate won't fit inside a bellhousing made for 157 tooth and the starter will be in the wrong location. There are 157 tooth type and 164 tooth type bellhousings for small blocks.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The next rebuild will include your cooling mods plus some of those by bucketobolts in his C4 improvements article. I may also add a wide ratio gear set that would aggravate the overly hard shifts.
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
The next rebuild will include your cooling mods plus some of those by bucketobolts in his C4 improvements article. I may also add a wide ratio gear set that would aggravate the overly hard shifts.

For some more understanding of the C-4 VB, take a look at this tech article.
Using your browser pointer you can click on the photos to expand them, then click the back arrow to resume reading the article.

http://classicbroncos.com/tech/c4-valve-body-service-and-modifications
 
Top