• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wrong harmonic balancer?

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Anyone getting sick of my questions yet? Haha

The new motor I recently installed turned out to be a HO 302 I used the balancer from my original 302 I have a pretty noticeable vibration at higher RPM. It's the balancer isn't it? Is there a good place to look for a replacement and what do I look for? It will need the 50oz if I'm reading everything right. Correct?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
What did you do about the flywheel/flexplate as well?

But for the damper on the front of the engine, yea you figured it out correctly. It is wrong.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Flywheel and everything came off of the old motor. bolted right up (at the time I didn't know it was an HO) and I'm just assuming thats what it is because The normal 302 firing order ran like crap and the HO firing order runs like a top.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Well, I hate to suggest assuming anything, since only the cam dictates the firing order. And a cam can be changed. Someone could have taken an old 302/5.0 and put a 351/5.0HO cam in it very easily.
But since you bought it as a late model engine, and everything else appears to be that way, short of looking at the crank I.D. numbers, might as well go for the new balancer and flywheel/flexplate.

That's what bowsher was saying. They BOTH have to match the crankshaft. Not just the damper. So you're going to be pulling the transmission too, to replace the flywheel. If you didn't intend to already that is.
I think I remember you mentioning that the one that came with the new engine looked too small. Very possible because many of those engines were in cars, that would have had the 157 tooth flywheel. Your truck application would normally have used a 164 tooth version. But either will bolt on, and it depends on what bellhousing you use. If a truck bellhousing meant for an 11" clutch, you would want the larger version. Larger is better in this case, as long as it fits.

One of the replies in your other thread mentioned Damper Dudes. They're in the business of re-balancing and maybe even doing custom dampers.
When you re-balance is when yours is either in such good shape it would be a waster to throw it out, or more importantly, it's one of the only ones you could find that would line up with all the pullies.

Otherwise, not sure what damper you're going to need by part number. Only that you absolutely need a 50oz imbalance damper.

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
All the balancers I've seen are 4 bolt 50 oz. where can I find a 3 bolt 50 oz?
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Thanks Paul, looks like I've got some (more) work to do.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Just to make sure I've got this. You're saying that even though the flywheel is working with no problem if I want to get the right balancer I have to change the flywheel too?
 

Ryanlt

Jr. Member
Joined
Mar 21, 2013
Messages
88
Loc.
Douglas, Ga
That's right, your flywheel is balanced to match the crank just like the harmonic balancer is. If your motor is a 5.0ho, then you'll need a 50oz harmonic balancer and a 50oz flywheel.

I ordered my parts from toms, they have a universal balancer that you can use a 3 or 4 bolt crank pulley with. Call them and tell them what you have and they'll set you up with the right stuff. They was very helpful when I swapped from my original 302 to my new 5.0ho and reused all my old vbelt accessories.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Well...That really burst my bubble. I just got this thing going. haha oh well. I guess it's going to be down again.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
This is the balancer/damper we sell. http://www.wildhorses4x4.com/category/s?keyword=harmonic
As mentioned, the 50oz or 28oz counterweight can be used with this damper depending on what engine it's used on. Has both bolt patterns and can change it's balance depending on what you're using it on.

This is designed for use with standard Bronco front accessory drive setups though. Not necessarily with later model setups unless the pulley mounting surface is at the same level.

Flywheels: http://www.wildhorses4x4.com/category/s?keyword=flywheel

Paul
 
Last edited:
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Alright excuse my ignorance but, I can use the 28 oz? I have a 28 installed right now with the matching flywheel and I have a vibration at higher RPM. When I figured out that I had the HO firing order I assumed it was the balancer?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sorry if I said anything that confused you Okie. But NO, as said before you can NOT use a 28oz balancer OR flywheel on a 50oz crank. Period.
The flywheel, crank and damper are required to work together to have correct balance. When the crankshaft design was changed, the damper and flywheel were changed as well.

So you have to source both a 50oz balancer and a 50 oz flywheel or you will be out of balance and have a vibration.
I added some extra wording to my sentence in the previous post to clarify a detail

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The firing order is determined by the crankshaft throws and the camshaft lobes working together to open and close the valves when the pistons are in the right position.

The change in firing order did not involve changing the crankshaft however, because four of the connecting rods share a pair of journals. It only changes with the cam. If you notice the numbers in the two firing orders. four of the numbers are exactly where they were in the older firing order and four are transposed to different positions. That's because the crankshaft throws are putting the pistons at the same position as before, but the cam is opening the valves on different cylinders in a new pattern.

So the 15426378 and the 13726548 are only different by the second, third, sixth and seventh positions in the firing order.

On a carbureted engine with the two different cams, all you have to do to compensate for the change in the firing order is to relocate where four of the plug wires are on the distributor cap.

Sorry if that made it more confusing. But firing order as we're discussing is only in relation to the camshaft and where you put the plug wires.
The imbalance factor is only in relation to the crankshaft and what damper and flywheel you use with it.

Paul

Paul
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Thank you Paul. That clarified it, sorry if I was being thick. I think I've got it now though.
 

Ourobos

Bronco Guru
Joined
Jan 7, 2008
Messages
1,225
Loc.
Big Island Hawaii
The firing order is determined by the crankshaft throws and the camshaft lobes working together to open and close the valves when the pistons are in the right position.

Actually the cam solely dictates the firing order, there are zero differences in crankshafts between the two.. Unless you're just making a comparison and included the crank in that.
 

jcrum

New Member
Joined
Sep 1, 2011
Messages
25
I think I have a similar problems to your. When I rebuild my 302 the guy at the machine shop already had a crank that was machined. So I bought it and put it in. Now my motor vibrates at low rpms and gets worst at higher RPM. The motor is a 1975 Bronco 302 put the crank not sure. It run great but vibrates way to bad to drive.
 

jcrum

New Member
Joined
Sep 1, 2011
Messages
25
it has a 2 piece seal I build it about 2 years ago. I have lost interest in my project because of the motor vibrations. But I'm trying to get back into it and finish it this summer.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Earlier 302 - Engine has a 28oz. Balance - 28oz, Balancer and Flywheel/Flexplate Required.

Later 5.0L HO Motor has a 50oz. Balance - 50oz. Balancer and Flywheel/Flexplate Required.

Cannot mix Balancer or Flywheel/Flexplate between the two engines.
 
Top