• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Sensitive steering issue on a 77 with 3.5 in SL

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
I have searched thread after thread and have seen similar problems without fixes and not the exact same issue. I am curious if anyone has had or knows of a fix for sensitive steering. I have a 77 with a JD 3.5 in SL and 2 in JD BL and JD extended radius arms. I had 1.7 degrees of caster with the 4 degree shims from the JD kit and have since replaced them with 7 degree shims which made daily driving much more enjoyable and normal. So i am figuring about 3 to 4 degrees of caster now, if that math works out. I am not using the track bar that came in the lift kit as the 77 already has a low trac bar bracket. I have the WH three way adjustable drag link and a JD steering dampener. I am running 15" x 8" Mickey Thompson III's with 33 x 12.50's. The trac bar and drag link are both at 16 degrees. The steering box bolts are tight as well. I am also running the Explorer serpentine with the explorer pump. The steering wheel with engine running can be spun with one finger lock to lock. It is not a big deal driving a straight line oor over pot holes no bumpsteer, however when I cross the centerline to pass hold on because I am about to go in the ditch or smack into the guy I am trying to pass. It is super sensitive. Everything is tight from the steering wheel to the pitman arm, the drag link rolls forward maybe a 1/8 inch before it pushes the tie rod. Loooking from the drivers side, while turning the steering wheel, it appears to be instantaneous though. my tire pressure is set at 27 psi all way around. I am sure I have forgot something and I will post photos of the trac bar and tie rod when I get home from work.

Would a steering box react this way if it needed rebuilt? During normal driving there are no issues which leads me to think that it has something to do with the tie rod and drag link or the angles of which the trac bar and drag link are at. I was thinking about going with a WH adj trac bar riser and a full length drag link but I don't want to throw parts at it and still be disappointed at the driveability.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Is the steering really light feeling? In other words does it feel like it takes no effort to steer the wheel? If so the torsion bar in the steering valve inside the box may be broken which will causse that issue. You've also described every part related directly to the steering, so I don't think you have a parts issue on the front, however I have had spring eye bushings on the rear springs and or loose ubolts cause similar issues. The minor shifts in crossing the ruts in the road when passing causes it to quickly wander. You could also have some tire issues, some chase ruts harder than others and can cause that headed to the ditch feeling too. Not saying you have any of these, just things I've found that can cause that issue.
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
Like Yeller stated, I would say its the torsion bar in the gear itself, it may be broke or just one of the smaller sizes which will make very easy to turn. You can have a larger size installed to increase road feel/resistance. The third paragraph down in this article talks about the torsion bar.
http://www.fourwheeler.com/how-to/power-steering-103/
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
Yeller, yes sir it feels very light in the steering. As a matter of fact my buddy commented on how light it felt and he said he and his buddy would love to have their EB's steer like thaton the trails. Which really makes me think something is out of whack for another EBer to say. If that is the case maybe we should buy some and "break" them and sell them as trail steering boxes. just kidding but it does do really well on the trails. The rear ubolts are brand new and the rear springs are james duff (Deaver) 11 pack springs. The whole SL and tires and rims don't have over two thousand miles on them so every thing is new. 60 miles roundtrip from my house to the base and back daily. Thanks for bringing that up though I hadn't really thought about that. It would explain why it feels the way it does, I was starting to think I was going crazy that it shouldn't feel that "light" but I haven't run into anyone that understood what I was saying.

trubotim2,

yes sir, the truck just received an alignment with the tires and most importantly I wanted to check the caster which is what drove me to changing out to seven degree bushings. Thanks

Surfer-b,

Thank you for the link,I will get arebuild kit, tear it down and see what's going on in there, It has just been a magic little box that I had no reason to open but now that you and Yeller are in agreeance that it is possible, it's enough reason for me to crack it open.
 
Last edited:

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
What are your camber, caster and toe numbers?
I have almost the same set up but with 35's and a track bar riser.

I played around with camber and noticed if you have the wrong camber it will also drive all over the place.
If I remember correctly you want around .1 to .5 degrees positive camber. You may need to install ball joint adjusters or camber shims to change thigns. I think stock is 1.5 degrees positive but that is too much when you have taller tires on.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Bad part is the torsion bar doesn't come in the kit... However it is easy enough to change the valve unit from 1 box to another as long as the boxes are of the same design for the valve. And if the box is tight and not leaking, it doesn't require disassembling the rack inside, just unscrew it out of the top and put the new one in. If you have a Saginaw box for instance most of the valves except for some of the later jeep boxes, the valves will all interchange.
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
JohnJohn,
After searching for nearly two hours i have discovered that i have failed to retain that alighnment sheet where I could find it however like I have heard on this site before I can always look through my old posts to find out details about my rig so here goes the caster with 4 degree bushings now changed to 7 was 1.7 degrees positive caster. Toe in is set at o.5 degrees and camber is 0. Thank You for reminding me about that.

Yeller,
I am still trying to determine what the steering box is. It is the factory one for the 77 with power steering. I called and have the rebuild kit coming in tomorrow however like you said there are no hard parts. I looked online and couldn't find much on replacement torsion bars. Back to research I guess. Will say a 2 wd 77 full ize torsion valve fit the factory box or should I say is there somewhere I can go to find that out? Thank You
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
The rear ubolts are brand new and the rear springs are james duff (Deaver) 11 pack springs. The whole SL and tires and rims don't have over two thousand miles on them so every thing is new.
Try retorquing the rear u-bolts. They will stretch a bit, especially when new. I run the Extreme Duty u-bolt kit from WH, torque them to 120 ft/lbs, and have retorqued them three times. I really can tell the difference after tightening!!
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
JohnJohn,
I didn't do anything except put the lift on and of course my 33/12.50's may be changing the camber by the backspacing, I am not so sure there though just a guess. I need to take it in and get another alignment and see if there is any variance between results from shop to shop I need to see what the 7 degree bushings put me at anyway. That will help me determine if I want to rotate the C's or not. Thanks


70_Steve,
I will try retorquing them as I haven't actually done that, It's been on the list but looking back that should have already been done. Thanks
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
I have another 77 so I will steal the steering box off of it and troubleshoot from there if I don't see any improvements from the retorque.
 

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
You may try and re-center your steering box and make sure your pitman arm is almost parallel with your frame rail.

I have almost the identicle set up that you have but WH lift.

After I installed my 3 way adjustable, I had it aligned. The shop extended the drag link way out which pushed my pitman arm way off center, maybe 30 degrees. I had very sensitive steering until I figured out what they had done.

Good luck.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
All good advice. Especially that last.
Couple of things come to mind:

1. New C-bushings in backwards. Happens all the time.
2. Steering box off-center. Also happens all the time. Takes a bit of work to determine, but well worth it for the long-run.
3. New steering linkage not adjusted properly. By your description, it actually sounds like it is, but I wanted to mention it anyway and will check out your photos when you get them posted up.
4. Tires. Are they new?
5. Pitman arm. "Usually" this setup needs a dropped pitman arm and (like you said) NO dropped trackbar bracket. But if both of your links are indeed at the same angle, then this is not an issue on yours for some reason. You already have a pitman arm?

That's about it for now. Most of that had been covered, but I thought I'd put it in a list.
Waiting to see the pics.

Good luck. A darty EB is not a lot of fun!

Paul
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
DirtDonk,

The bushings are installed correctly but I see how they could be installed incorrectly if you weren't paying attention. In my case I would have great pinion angle if they were installed backwards. I might have to rotate the C's to gain a better pinion angle but one problem at a time. The steering was centered at the alignment shop back in September '13 and the tires are new. I have a WH drop pitman arm for a 66-75 EB. Thank you
 

Attachments

  • DSC_0002.jpg
    DSC_0002.jpg
    104.1 KB · Views: 119
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Great result!
Have you driven it yet? Looks like the links are nice and parallel now from what I can see.

Paul
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
Paul,
actually I haven't had time this weekend to do anything except throw a photo up, I haven't been able to fix it yet. It has been wet and we had thunderstorms come through. I drove it to work tonight and she'll do 80 in a straight line. This problem isn't exaggerated until I cross the center line to pass. Ordinarily, it just drives like a thirty year old vehicle. I am definitely leaning toward the gearbox change and/or retorque. I hope to do the retorque in the morning and then swap gearboxes later in the week if the torque on the rear axle u-bolts is still good. Thanks.
 
OP
OP
J

jimnrenee's77EB

Jr. Member
Joined
Aug 7, 2010
Messages
50
Loc.
Ward, AR
Surfer-B,

Thanks for the link, I just talked with Ronnie and he said for less than 300 he would rebuild it oversize the ball bearings and oversize the possibly broken torsion bar that Yeller and you were talking about. I will be going this route since I only got a quarter turn on the rear ubolts. He said the steering will feel like a corvette when I get it back. Thanks again.
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I still think your Camber at 0 is not helping. Stock the D44 should have had 1.3 to 1.5 built into the outer C's. It’s strange to have 0 without shims or ball joint adjusters.

I had 1.5 and it was way too much for 35's so I installed ball joint adjusters and tried different settings. When I hit 0 it drove badly. I had positive on one side and negative on the other by accident and it was worse. I can’t remember but I think I am at .5 positive on both sides and it drives fine now.


Check out this recent post about camber as well.
http://classicbroncos.com/forums/showthread.php?t=239813
 
Top