Susan76
New Member
- Joined
- Jun 20, 2013
- Messages
- 30
Finally fired my 76 302 C4 from a 10 month overhaul and mods... what has been done?? well from the front winch to new cover on the spare tyre -- lots... complete new wiring harness with 16 circuits from headlights to taillights+++ new seals everywhere except the balancer. Edelbrock Performer with Holley 470 Truck, reman 1970 single point dist. 23 gal tank with SW elec fuel pump at the tank - filters before the elec pump (2" from the tank outlet) and at the carb. MSD old school coil (circa 1970 left over) Taylor 8 mm wires & Motorcraft plugs. Rad tanked & rodded. Timing at abt 2* when I fired it the first day (eyeball). It was running good and started in what seemed to be 1/2 revolution - hot or cold.
few other items C4 rework with deep girdle pan, locker rear, tru track frt, driveshaft, 140 map alt isolated to dual batteries for the Warn VR10K, Lowrance GPS, Corbeau seats, onboard air, frt & rear cameras, halogen & LED lights frt & rear++++++++
Fire it up after prefilling the carb to check floats. I wasn't able to drain the block so I fired it "semi dry" as I wanted to get it out to run coolant cleaner through it and flush it a couple of times before hooking up my new heater core. Did about 8 short warm up and cool downs as I checked trans fluid (complete drain inc converter and new cooler), ps etc to get all the air out. Finally added coolant and ran about 1/2 hr a couple of times. I had set my new T steering with a tape measure so first drive was directly to the alignment shop. maybe 2 miles.. Got there and it started stalling. Had to left brake to get it on the rack and off. Took it for a 20 mile drive - about 12 hghy and rest in town... some times it would buck and a couple of times or stalled after taking off from stop signs like no fuel. Had to feather the throttle to keep it going but then good for a couple of miles. When it stalled, it started right back up 8 out of 10 times. Couple of times trying 1/3 1/2 throttle it would chirp the tyres going into second and no nosing over in 2nd. Got home after picking up cleaner for cooling system and it would barely run.
In the shop, timing reset to 6* and I realize the mark is "bouncing" 4-6*. Could barely keep it running -- so check timing - check floats - check firing order and it keeps getting worse... Pulled the carb bowls looking for anything that could get past the filters (or from Holley). Replaced the filter at the tank which had picked up apparently loose stuff in the tank. Tank had been in place & dry since last sept. I even bought a new gas can for the first gas to go into it.... Set to pointer at 20* and hand on fan cranked back until the rotor moved and it seems like about 6-8* of "slop" as I did it 3 times.
Any idea what is the tolerance on a sm block timing chain? I am going to grab the carb off one of my 428s and try it just to replace the "new" Holley with a known working one.
Suggestions?
Susan
few other items C4 rework with deep girdle pan, locker rear, tru track frt, driveshaft, 140 map alt isolated to dual batteries for the Warn VR10K, Lowrance GPS, Corbeau seats, onboard air, frt & rear cameras, halogen & LED lights frt & rear++++++++
Fire it up after prefilling the carb to check floats. I wasn't able to drain the block so I fired it "semi dry" as I wanted to get it out to run coolant cleaner through it and flush it a couple of times before hooking up my new heater core. Did about 8 short warm up and cool downs as I checked trans fluid (complete drain inc converter and new cooler), ps etc to get all the air out. Finally added coolant and ran about 1/2 hr a couple of times. I had set my new T steering with a tape measure so first drive was directly to the alignment shop. maybe 2 miles.. Got there and it started stalling. Had to left brake to get it on the rack and off. Took it for a 20 mile drive - about 12 hghy and rest in town... some times it would buck and a couple of times or stalled after taking off from stop signs like no fuel. Had to feather the throttle to keep it going but then good for a couple of miles. When it stalled, it started right back up 8 out of 10 times. Couple of times trying 1/3 1/2 throttle it would chirp the tyres going into second and no nosing over in 2nd. Got home after picking up cleaner for cooling system and it would barely run.
In the shop, timing reset to 6* and I realize the mark is "bouncing" 4-6*. Could barely keep it running -- so check timing - check floats - check firing order and it keeps getting worse... Pulled the carb bowls looking for anything that could get past the filters (or from Holley). Replaced the filter at the tank which had picked up apparently loose stuff in the tank. Tank had been in place & dry since last sept. I even bought a new gas can for the first gas to go into it.... Set to pointer at 20* and hand on fan cranked back until the rotor moved and it seems like about 6-8* of "slop" as I did it 3 times.
Any idea what is the tolerance on a sm block timing chain? I am going to grab the carb off one of my 428s and try it just to replace the "new" Holley with a known working one.
Suggestions?
Susan











