• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Here's another EFI question for the Guru's...

Sporto

Sr. Member
Joined
Oct 10, 2005
Messages
923
OK,
Have a basic older 302. Did an EFI conversion a year or so ago with an 86 Mustang GT Speed Density setup. Run the two pump (Carter LP -> E2000 HP) setup. Harness is setup with added relays and fuses.

Everything runs great, and has done so for past year. Recently had an issue...Engine died on highway. Nursed it home, check engine light came on, ran codes ended up with code 87 ~ Fuel Pump issue. Swapped out FP relay, problem solved.

Now I get this problem sometimes. I drive it normally, I shut it down (for the day or whatever), then go start it. No priming of pumps, no start, CEL comes on. I pull the fuse to disconnect ECM and I take out FP relay. Let sit for a minute or two. Reassemble, pumps prime, no CEL and engine starts no problem. This happens sometimes, and I am not sure what is causing it.

I tried several relays when it is offline and it does not make a difference. It just needs to sit for a few unplugged and it works again.

Just not sure what is going on...

Setup ~
86 Mustang SD
ECM ~ VR1
Codes ~ Just EGR ones
Stock orange injectors
Stock TFI distributor
302 with Edelbrock Performer Cam
Stock Manifolds
O2 sensors in each pipe

Thanks for any advice!

Rich
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Rich, probably not much help but I think I have pretty much the same set up as you (Ransil special?!) and when I was having occasional issues with the engine dying, it was a ground problem. I figured it out before I ever needed to run codes so not sure if it would have thrown the same code or not.
 
OP
OP
Sporto

Sporto

Sr. Member
Joined
Oct 10, 2005
Messages
923
Rich, probably not much help but I think I have pretty much the same set up as you (Ransil special?!) and when I was having occasional issues with the engine dying, it was a ground problem. I figured it out before I ever needed to run codes so not sure if it would have thrown the same code or not.

Hi Gary,
You are correct Sir! It is a Ransil special (at least some of it is), I do have the grounding block on the firewall (that he installed) and all wires routed to that. I am thinking that it has to do with the EGR delete or the incorrect firing order on the older engine. It is an odd issue, more of a PITA than anything, but I don't like the idea of it not being 100% reliable.

Hope you're enjoying the Texas life!

Rich
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
Hi Gary,
You are correct Sir! It is a Ransil special (at least some of it is), I do have the grounding block on the firewall (that he installed) and all wires routed to that. I am thinking that it has to do with the EGR delete or the incorrect firing order on the older engine. It is an odd issue, more of a PITA than anything, but I don't like the idea of it not being 100% reliable.

Hope you're enjoying the Texas life!

Rich

I didn't touch that harness!!! that's all you ;D

I would have left the EGR in there only the cool kids remove and I'm not them.

EGR delete should have nothing to do with a FP code.

Install a breakout out and probe the FP wire.

check the Fuel pump grounds
check fuel pressure
check fuel pump voltage at the fuel pump.
 

EricLar80

Bronco Guru
Joined
Jun 14, 2001
Messages
2,170
When I first put in my EFI conversion, I would develop issues with the fuel pump relay. It was the box relay that Autozone supplied as a replacement for the factory one; it plugged into the harness. What I concluded was A) the AutoZone relay was crap, and B) I think it was affected by the heat in the engine compartment. Either get a good one from Ford, or change it out for some aftermarket relays that are accepting of higher underhood temperatures. If you bang on it, sometimes it will start working again, which is indicating the contacts or coil inside is shot.

Note that you can use any SPST (single pole, single throw) NO (normally open) automotive relay with a high enough continuous duty amperage rating. They will sometimes be called SPNO.

Eric
 
OP
OP
Sporto

Sporto

Sr. Member
Joined
Oct 10, 2005
Messages
923
I didn't touch that harness!!! that's all you ;D

You are correct Ransil... This is my harness, and FWIW it runs great 99% of the time!

I will take a closer look at the relay (it is a Ford or a Bosch) in there now. After the first failure, I swapped in what I thought was a better relay, but it was used, so I think that I will just bite the bullet and buy new Ford/Bosch ones, and see where that leads. Like Eric suggested...

If that does not cure it, then I will do some more research on the harness with my breakout box when it happens.

Thanks

Rich
 

welndmn

Bronco Guru
Joined
Nov 12, 2001
Messages
2,112
Have you checked the EEC relay for power when this happens?
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
I thru some extra relays in my stuff pick the up at the wrench & roast
 
OP
OP
Sporto

Sporto

Sr. Member
Joined
Oct 10, 2005
Messages
923
I thru some extra relays in my stuff pick the up at the wrench & roast

Awesome! Right in the same bag as my lift off hinges. ;D

Nice!

See ya next weekend!!

BTW ~ I think that I have worked my way up to Chief Bottle Washer level at the W&R, and I am pretty sure that you can find someone else to give the crappy clean up chores to this year. :cool:
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
We have been training your replacement ;D
 

Attachments

  • IMG_20120728_214550.jpg
    IMG_20120728_214550.jpg
    114.8 KB · Views: 89
Top