• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

76-77 dana 44 measurement

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Once you get the radius arms in place and start to snug the bushings, take a channel locks and you can rotate them into the correct position. You will be able to see and feel it when they are in the right spot.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Look carefully. That is 451 and a typo on the lbs.


It a typo alright, but not 451 ft.lbs. The whole sheet has 1's where /'s should be. You'd have a tough time trying to get to 451lbs. 150-200ft.lbs. would be a realistic figure. Hopefully moses_m will do some research to get the correct torque. it's kind of a critical area.

Mark
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Havent snugged them up all the way yet. They are currently at 100lbs.
Have some questions
Is my trac bar installed correctly? Had to use a ratchet strap to line it up. Used top hole on drop arm bracket. Bottom hole had stabilizer bar on dana 30.
At full droop without tires my front diff wants to pull toward the drivers side.
Is the pumpkin making it lean that way?
After I installed wheels it looked like it lined up good.
baja wheel with 4" backspacing did not fit on passenger side it rubbed on heim hardware. Baja wheel did however fit on drivers side.
Installed a hellcat with 3 5/8" backspacing on passenger side. So for the meantime I will run 3 bajas and 1 hellcat. WH spacers on order.
I think if I went with a different heim setup that doesnt have both heim joints on the knuckle the 4" backspacing would of been tight but it would of worked.
I also noticed that before I even installed different diff I already had some bronco lean. The bronco has a 2 body lift and was on jack stands at the frame as I upgraded suspension and both diffs. Could it just be the 12 gallon steel aux tank I have on drivers side? I checked the C cap bushings that were previously installed and they were cleary marked and installed correctly. They were rancho bushings. Do you think if I install new body mounts it might help a little. Or even change up the sizes? Just wanted to ask as most of the bronco lean I read it has to do with the bushings being installed backwards and that just isnt my case as I have it with diffs off. Will check tomorrow if one of the bushings on lift isnt shot. By the way I can live with bronco lean (swag). Thanks again for the help
 

Attachments

  • IMG_20141210_214541_434.jpg
    IMG_20141210_214541_434.jpg
    45.1 KB · Views: 20
  • IMG_20140709_155531_910.jpg
    IMG_20140709_155531_910.jpg
    107.2 KB · Views: 26
  • IMG_20141210_201920_786.jpg
    IMG_20141210_201920_786.jpg
    87.8 KB · Views: 32
  • IMG_20141210_201734_196.jpg
    IMG_20141210_201734_196.jpg
    91 KB · Views: 22
  • IMG_20141210_201856_611.jpg
    IMG_20141210_201856_611.jpg
    62.8 KB · Views: 30
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Posted one wrong pic. Here is pic of hardware behind hellcat wheel.
 

Attachments

  • IMG_20141210_214648_910.jpg
    IMG_20141210_214648_910.jpg
    82.2 KB · Views: 30

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Having to pull it over to line up is normal. But you can't set it up correctly until the weight of the vehicle is on the ground. Useless to set up at full droop or compression. It's the neutral ride-height where you use an adjustable trackbar, or check the location of your stock one.

You can't use the upper hole. That's the stock original one (or close to it anyway) and is for another bolt. The trackbar goes to the lower one except where there are two additional holes at different angles for different settings.
You can verify this by the extremely un-parallel angles of the two bars. You want the angles of the trackbar and draglink to be as close to parallel as you can get. Not always easy when you use a system that uses a substantially longer draglink, like you have. But it's still desirable to get it as close as possible.

And it doesn't matter where it starts, the way these suspensions work your axle will ALWAYS slide towards the driver's side when the suspension is extended, and back to the passenger side as the suspension compresses. It's just the nature of the beast.
What you're striving for is a trackbar that is as close to parallel and the same length and pivoting from similar planes as the draglink, and (where reasonable) as level as possible. More angle is less desirable, less angle is better. As a general rule.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Well that's looking pretty close! But hey, as long as it clears, you're good to go.
Wheels do flex though, so when they're super close, there are some circumstances where they can actually hit. Luckily here though, that location on the circumference of the wheel is not as likely to flex inward under normal use as are other parts.

But definitely try the lower hole on your trackbar bracket.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Oh (he says, adding merrily to his post count...), if you need to remove the upper mount anytime, whether to move it to a different hole or adjust to center the axle at ride-height, a simple way to get it lined up is to always do it with the tires on the ground.
With the rest of the steering linkage connected still, you simply turn the steering wheel one way or the other. With the trackbar disconnected like that, moving the wheel literally moves the body/frame over the axles. It's very disconcerting the first time you see it, but it works wonders on lining up your upper mount bolt!

It makes such an easy job of it, if you're by yourself you can literally reach up between the frame and body and grab the steering input shaft and rotate it by hand to do the same thing.
Of course, it's easier and more fun to have a helper sometimes, but in a pinch you can do it by yourself. You can try the wheel by yourself too, but it doesn't always stay right where you want when you let go of the steering wheel.

You can check for axle being on center with some tape, a marking pen, a home-made plumb-bob and a tape measure.

Good luck.

Paul
 
Top