• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

High temperature issues

69bronco69

Full Member
Joined
Jul 9, 2011
Messages
190
Loc.
Central Arkansas
Have a 69 stock 302 w/o shroud with 80k miles. Had stock radiator replaced with stock radiator from Tom's 3 years ago. Two summers ago I had the gauge cluster refurbished with stock gauges. Before it showed operating temp at 185-195. After refurbish, it showed temp at 200-210 After sending it back twice, it tested to be within the specs. I resigned to the fact it would run like it always had, but at new range of 200-210.
Past couple months, notice a bit of oil collecting in spaces above water pump and timing cover. Knew gasket replacement was in near future.
This week, I notice after short drives I was leaking antifreeze. It was coming from my over flow tank. So I guess it was getting too hot. I remember my dad having the water pump replaced once before many years ago.
This is what I had done from local mechanic:
Valve covers removed and replaced the gaskets-they showed leakage too.
water pump, timing chain/gear, timing chain cover were all replaced with new gaskets
Replaced intake gasket.
Radiator flushed.

Now it seems to run a bit hotter than before by creeping up on 215-220 at stop lights but still 200-210 at highway speeds.
Any chance this coolant issue is a t-stat or sender issue?

I plan on taking this up with mechanic on Monday - I picked up bronco from him near closing time on Friday. So by the time I noticed issues, he was closed.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
Without a fan shroud?

You really need to put a fan shroud on it.
Make the fan pull the air through the radiator not just move air around in the engine compartment.

The leaks are another issue.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
You have given alot of good data but be prepared to come up with more.
These fellers here at cb are freaking amazing but they will probably need a little more information.
They will get you through it.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Your mechanic did all that - intake removed, water pump, timing cover, flushed radiator -- and didn't put a new thermostat and gasket in it?!?

First things first. Buy a fan shroud and put it on. Its important.

In the meantime, check your radiator cap. If it's not holding proper pressure, it releases coolant to the tank, the tank releases it to the ground. If its old and you are unsure about its condition, just by a new one and put it on, its like 10 bucks. Fill the radiator with a 50/50 mix of good antifreeze (boron-free, most major brands are) and DISTILLED water, NOT tap water. You can get distilled water at any Food Lion or other grocery store for about $1.50 per gallon, buy a few to keep in stock. (Tap water has all kinds of minerals and crap in it that react with the metal in your engine and radiator and will clog the passages in a new radiator in a New York minute.) With the new cap and full of coolant test drive it and see if the problem persists.

If it doesn't, great. If it does, replace the thermostat and gasket. Get a 180 degree. With a 180 degree thermostat, your engine should maintain a temperature very close to 180. It may rise slightly at a stoplight in summer, but should be consistently close to 180 under most all driving conditions. I don't know your mechanical ability, but if possible, do it yourself, its not that difficult and will save time and money. To me, it sounds like the thermostat is probably the issue. Most likely stuck open and won't allow the coolant to stay in the radiator long enough to get cooled off.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Some fellers here suggest going to a 195° T-stat to keep the coolant in the radiator longer.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Some fellers here suggest going to a 195° T-stat to keep the coolant in the radiator longer.
One reason for using a hotter thermostat is because it makes the heat exchange from the radiator to air more efficient. The bigger the difference in the temp between the radiator and the air the faster the heat is exchanged.
 
OP
OP
69bronco69

69bronco69

Full Member
Joined
Jul 9, 2011
Messages
190
Loc.
Central Arkansas
This bronco has been in the family since it came off the lot in '69. I honestly don't know when the shroud was removed but it was a long, long time ago. This running hot issue is kinda new. I agree I need a new shroud and have one on order.
Let's say I get new shroud, new t-stat and the problem still exists. Then what do we look at other than the temp sending unit?
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Point an IR thermometer at different spots, top of radiator, bottom, etc to double check real temp.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Having this car in your family for that long, I'd think it is probably still pretty much unmolested by "parts changers." If your car is overheating at all, it sounds like a minor issue.
Usually there is a reason for overheating, not deficient stock parts. There have been a number of overheating cases here where the owner threw all new aftermarket parts at it and found the thermostat or head gasket backwards. A well maintained stock system with all the parts intact is hard to beat. If you haven't had the radiator professionally rodded or flushed, take it to a radiator shop for testing. Then when you reinstall it, put in your new shroud.
 

Bonco4Broncos

Full Member
Joined
Feb 9, 2015
Messages
161
Loc.
Rockingham, NC
And the oil puddling near the Distributor shaft is likely caused by the O ring around the distributor housing. Not hard to fix at all. Alot of older Fords with any miles at all on them had a puddle there.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
People that tell you the coolant needs to stay in the radiator longer aren't thinking it through.

If the coolant in the radiator stays there then the coolant in the engine is staying there longer too, and getting hotter instead of moving the heat.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
People that tell you the coolant needs to stay in the radiator longer aren't thinking it through.

If the coolant in the radiator stays there then the coolant in the engine is staying there longer too, and getting hotter instead of moving the heat.

I know what you mean. There may be something to the theory of the coolant moving too fast to absorb the heat, but I doubt it has anything to do with this problem.
I use a 194 degree thermostat because it seems to make my engine peppier. The cooling system worked fine with the 180 degree one too.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Don't worry about your sending unit, it won't cause your engine to run hot and push coolant out. It simply tells your gauge what to say.

If the cap and/or the thermostat don't correct the issue, there are only a couple of things left.

First, shine a flashlight through the front of your radiator and make sure you can see through it all over, pay special attention to the corner areas. If there are "holes" that are clogged at various places, clean your radiator. What works best is an HVAC core cleaning solution that you spray on, it foams-up, and then washes off with a strong garden hose stream, but you can use any good household cleaner like 409. Just spray the entire radiator liberally and let it soak for a few minutes before spraying it off.

If you are confident your radiator is clean, then, with your engine warmed-up and running at operating temp, look at your radiator hoses and make sure they are not collapsing and blocking flow, if good then, as 73azbronco said, get an IR (laser) thermometer, you can get one at Harbor Freight for about $20 or so, point the beam at various spots on the front of your radiator through the grill. Look for drastic variance in the readings, focus on the corner areas at the top and bottom, the center areas will always be a little lower temp because those areas get more benefit of airflow from the fan. If you find large differences, you most likely have a partially clogged radiator and it will need to be removed and professionally cleaned ("rodded").

If that doesn't correct the issue, then most likely you have a blockage in your engine's water passages somewhere and the only thing to do is sell me your truck for a few hundred dollars. :cool:
 
OP
OP
69bronco69

69bronco69

Full Member
Joined
Jul 9, 2011
Messages
190
Loc.
Central Arkansas
If that doesn't correct the issue, then most likely you have a blockage in your engine's water passages somewhere and the only thing to do is sell me your truck for a few hundred dollars. :cool:

All that sounds good, except for the selling part. :):):). Too many memories with my dad in that Bronco. Since he past away in February, selling is not an option.

I will contact the mechanic about the thermostat on Monday to see if they checked that out. If the t-stat is the issue I feel confident I can change that out. The water pump was bad so I figured that was the issue, maybe mechanic thought so too. Taking those bolts out of the block kinds scared me a bit. That is the main reason I went to mechanic.

Lots of great advice. Thanks to all. I will keep you updated.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Condolences.

If you do change your Tstat yourself:
-- drain your radiator with the petcock at the bottom.
-- keep in mind they are directional, most are marked "to rad" but some are not. The pointy end goes to the radiator, the spring side in the engine.
-- clean your gasket surfaces well, install a new one with a thin coat of Permatex, I like Type 2. I stuff a rag in the hole to keep bits from falling in the intake, just remember to remove.
-- don't overtighten the housing bolts, they are 5/16 so about 17 Ft Lbs is all you need, if you don't have a torque wrench, I just use a small 3/8 ratchet and tighten them alternately until they are good and snug with my weak hand (I'm right handed so I use my left).
-- go ahead and get a new by-pass hose if your mechanic didn't, most of the time you have to cut them off to remove, and they are cheap.

Again, condolences, g
 
Top