• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Welding a cracked D44 housing?

kholding

Bronco Guru
Joined
Sep 6, 2010
Messages
2,209
Loc.
Las Vegas, NV
Sourced a '76 full-width D44 from an F150, removed the brackets/wedges and sent it to Currie to weld on new wedges at the EB width. After they had it for a couple of weeks and finished welding on the new wedges, they noticed it had been dropped and cracked. I know it wasn't damaged when I sent it to them but it could have been dropped by UPS during delivery. We will never know now. My question is can this be welded/repaired (at a reasonable price)? I know welding cast iron isn't easy but has anyone done something like this in the past or is this housing a 90b paperweight at this point?
 

Attachments

  • IMG_3006.jpg
    IMG_3006.jpg
    130.4 KB · Views: 225
  • IMG_3005.jpg
    IMG_3005.jpg
    146.5 KB · Views: 221
  • IMG_3004.jpg
    IMG_3004.jpg
    121.3 KB · Views: 180

Whoaa

Bronco Guru
Joined
Sep 26, 2014
Messages
1,059
I'm confused about this storey. They returned it to you in this condition, or just "noticed" this damage after doing all of their work to it?

Welding that crack in the 3rd member is a peice of cake. Yes, it is cast but a ductile alloy that welds nicely. You could easily weld it with mild steel from a common wire feed, or get fancy and TIG weld it...either way, once its ground down and feathered in you'll never know it was ever damaged.

Did they cut/rotate the knuckles and the wedges?

...

Tell me more about this new housing? I assume it must be a high pinion. And I'm also assuming you're doing the trick setup to have really sweet Caster angle of about 6 degree positive, AND have nice pinion angle for the front shaft. What gears will you be running, tire size, lift amount, and what carrier...ARB?
 
OP
OP
kholding

kholding

Bronco Guru
Joined
Sep 6, 2010
Messages
2,209
Loc.
Las Vegas, NV
They "noticed" it was cracked after they welded the new wedges to it. I had them re-weld at the stock angle as I already have this same axle with a 3.5" lift and it works perfect with about 6 degrees of caster.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
If it was mine I would drill 1/8 holes just outside the crack ends. Then I would Vee the crack and heliarc with everdur rod. If no heliarc I would do the same prep and arc weld with nickle rod. Neither repairs are cheep if you have to buy a whole package of rod.
 
OP
OP
kholding

kholding

Bronco Guru
Joined
Sep 6, 2010
Messages
2,209
Loc.
Las Vegas, NV
Currie apologized and said that I wouldn't need to pay for the work. They said they should have checked it before the work was done. Unfortunately, it sat in their warehouse for a couple of weeks so no way to say if the damage occurred during shipping and therefore no way to get a claim through UPS.
 

Nathan43

Full Member
Joined
Jun 26, 2014
Messages
318
Loc.
Provencal, Louisiana
If it was mine I would drill 1/8 holes just outside the crack ends. Then I would Vee the crack and heliarc with everdur rod. If no heliarc I would do the same prep and arc weld with nickle rod. Neither repairs are cheep if you have to buy a whole package of rod.
I agree with rustytruck. Drilling the 1/8" holes prevents it from cracking further, though I doubt it would crack much further anyway.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I would weld (or have it welded) and run with it. Trick is to find a good welder that knows what they are doing. I know our local Cat dealer (mining equipment) welds engine blocks back together after rods make windows in them. This would be an easy job for one of there welders. The local guy who welds fences and bumpers, not him. Maybe check with the local welding supply shop, they often know who the good welders are and who would take on the job.
 

Wyflyer

Bronco Guru
Joined
Apr 1, 2008
Messages
2,920
Welding that crack in the 3rd member is a peice of cake. Yes, it is cast but a ductile alloy that welds nicely. You could easily weld it with mild steel from a common wire feed, or get fancy and TIG weld it...either way, once its ground down and feathered in you'll never know it was ever damaged.

X2 ^^ I'd try to knock the dent out then weld it. The fact that it dented in tells you everything you need to know. If it bends it's plenty malleable to weld with mild steel rod.
I'd grind it down to fresh metal, bevel it and weld the filet with wire feed or 7018 stick rod and press on. I don't see it as any more complicated than welding on mild steel.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
If it was mine I would drill 1/8 holes just outside the crack ends. Then I would Vee the crack and heliarc with everdur rod. If no heliarc I would do the same prep and arc weld with nickle rod. Neither repairs are cheep if you have to buy a whole package of rod.

X2...pre and post heat and you shouldn't have any issues. It would be a good opportunity to weld the tubes to the center section at the same time IMO.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Is it still at their place?

I'd call Curry one more time and explain how you really don't want to get the BBB or a lawyer involved, explain it wasn't broken when it left your place nor most likely when it showed up. That leaves one option, they damaged it, they are completely responsible by commission or omission in a fair duty to care for the part, and it took two weeks to finally realize it. But they are now hoping you go away quietly.

Or was it damaged before it left your place? I'm having a hard time believing they couldn't see something like that as soon as it shows up. BTW, those hits do not look like rock hits, more like being dropped onto or hit with a tool. No scrape marks.
 

ScanmanSteven

Bronco Guru
Joined
Dec 19, 2010
Messages
1,129
Let Currie weld it. They know what they're doing, let them do it. Welding Dana pumpkins is easy, many of us weld track bar risers, hydro setups, weld tubes, 3 link setups and braces. Are you concerned about the wedges they welded on, no, so don't worry about a little crack. I'd clean it real well and weld the inside also.
 
OP
OP
kholding

kholding

Bronco Guru
Joined
Sep 6, 2010
Messages
2,209
Loc.
Las Vegas, NV
Definitely not damaged before I sent it. Currie had it for a couple of weeks, they called me to confirm what was being done and then another week or so went by and when I called to check on it and they said they found the crack (after they did the work). They apologized and said their tech should've checked it before completing the work but forgot to. They never once said they could fix it? I assumed at that point that they thought it was junk.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
It almost sounds like they are hoping you just take it, and once its out of their care, its your problem. I would call them back and question them more about it , and why, when they received it, they did not inspected it, before accepting it from ups.
 
Last edited:
OP
OP
kholding

kholding

Bronco Guru
Joined
Sep 6, 2010
Messages
2,209
Loc.
Las Vegas, NV
Spoke with the sales guy I have been dealing with and he initially said they couldn't weld it. He said that the welds never work. I explained to him that I had multiple sources telling me otherwise. He said he would look into it further and get back to me in the next 2 days. Will let you guys know what they say.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Actually, agree with them, They damaged it or failed in their due diligence to inspect it until after they did work on it. They failed on this item, the lower echelon folks are hoping you go away.

Tell them you agree, they cannot weld it, so what axle are they going to give you to replace the one they damaged? This is not an opportunity to come out with some rock crusher extreme unit, but they owe you what they had possession of and damaged. Ask for a manager if all else fails, then owner.
 
Top