• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

identify cast or steel camshaft gear

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I have a late 70's 351w and have no idea what cam the PO installed. I am at the point of doing a distributor modification and realized I need to determine if the camshaft gear is steel or cast in order to select the proper distributor gear.

I understand most flat tappet cams are cast, but I don't want to take any chances.

Is there a way to determine what this existing gear is without removing the camshaft?

I was thinking maybe a magnet would work but looking for verification.

Thanks.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I'm sure someone will verify for sure, but generally speaking if you have a flat-tappet cam, you need cast. If you have a roller cam, you need one of the other compatible materials (steel, brass, whatever-obtanium etc?).
The only exceptions I can think of would be a custom racing flat-tappet cam that would have been made from billet steel or some exotic material that requires a special material on the distributor gear.
Unless you've got one of those, you're probably good to go.

Have you pulled the distributor yet? Easiest way I know to see what you need is to see what you have. if a rough textured cast gear, that's what you replace it with. If a smooth steel or bronze or plastic gear, that's what you replace it with.
The only bummer is that I've seen some steel roller-compatible gears that had slightly rough finishes and would have been hard to tell the difference unless they were side by side with their opposite number.

If all else fails, look inside to see if you have a roller cam. Doubtful, but as we know, you never know...

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
The existing dizzy is a transplant so I can't go by that which is why I have to identify gear on camshaft. I am 100 percent confident I have a non-roller.
 

hankjr

Contributor
Bronco Guru
Joined
May 11, 2013
Messages
1,761
I think I read that one can "touch" the surface of a gear with a grinder in a non critical surface. Cast and steel give off different colored sparks. I've never done this so I can't vouch for the accuracy.

Hank
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
I can look at cast and forged and tell a difference on factory gears. The cast has areas that splines are not cut that have the ruff and bumpy areas like cast steel looks and the forged is all perfectly smooth. Post a picture.
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
like this
 

Attachments

  • cast gear.png
    cast gear.png
    57.5 KB · Views: 304
  • forged.jpg
    forged.jpg
    14.6 KB · Views: 170

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Well, it's certainly never a bad idea to make sure of something, but at the same time you may be overthinking this. If it's a non-roller cam, you can pretty much "assume" (yep, there's that dreaded word!) that it just needs a standard gear on a standard distributor. As in, cast gear like you would get right off the shelf at any auto parts store, or from any aftermarket manufacturer making a distributor for a 351W prior to the mid-nineties.

Did you pay a lot of money for this engine that makes you believe that the PO might have gone all exotic on you and put a $2000 race cam in it?
Just curious.

Just as easy to check as the gear, would be the cam material itself. If you remove the intake and look through the valley holes, the material in-between the polished cam lobes should look a lot like the gear on the left in rj's pic above. Dark, rough textured and nothing exotic.

If you're not sure, and can't tell from the cam gear, and are not sure from info the PO gave you, and definitely want to know for sure, you might find the work to remove the intake is well worth it.
Too bad that most cam manufacturers stamp their part numbers on the rear end, rather than the front. Be nice if you could just pull the timing cover and gear off, and read what part number it is.
But that'd be too easy...

Besides, I think I'd rather go through the intake R&R steps than the front cover anyway!

Oh, and regarding your question about the magnet, I would think since they're all ferrous metals, you're going to get the same reaction from a cast-iron cam and you would from a steel cam.
Wouldn't that be correct? The magnet would be attracted to both?

Good luck.

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Here it is. If you are talented enough to ID from this pic, I am impressed.
 

Attachments

  • uploadfromtaptalk1437492164045.jpg
    uploadfromtaptalk1437492164045.jpg
    65.9 KB · Views: 227

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
They sure are. They sell them to the cam manufacturers and what they do to the price is outrageous. Designed and made for Nascar engines with an expected life of 100,000 miles. What else you going to do guess and ruin a cam, gear and pump metal in your motor? I'd rather spend 80 bucks than pull a motor apart to check the cam. You'll spend that much on gaskets and you haven't bought a gear yet.
 

lonesouth

Contributor
Bronco Guru
Joined
Dec 18, 2003
Messages
5,048
They sure are. They sell them to the cam manufacturers and what they do to the price is outrageous. Designed and made for Nascar engines with an expected life of 100,000 miles. What else you going to do guess and ruin a cam, gear and pump metal in your motor? I'd rather spend 80 bucks than pull a motor apart to check the cam. You'll spend that much on gaskets and you haven't bought a gear yet.

just imagine if they got the price down to roughly 2x(guessing that is the price point where it is more cost effective to manage a single part instead of two) the cost of the cheaper(cast or forged) then sold it to all of the distributor manufacturers. That'd be real money. Unless it is just prohibitive to get the cost low enough.
 

ren71

Sr. Member
Joined
Oct 13, 2010
Messages
536
They sure are. They sell them to the cam manufacturers and what they do to the price is outrageous. Designed and made for Nascar engines with an expected life of 100,000 miles. What else you going to do guess and ruin a cam, gear and pump metal in your motor? I'd rather spend 80 bucks than pull a motor apart to check the cam. You'll spend that much on gaskets and you haven't bought a gear yet.

I've read about failures with composite gears. Probably lasts long in Nascar engines because the cam doesn't have to drive an oil pump, they use a dry sump system right?
But like you said, cam manufactures seem to trust them and think they're worth the money.
It does seem like a good solution to insure compatibility without opening the motor up, and great point about the cost of a gasket set.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I hope it's just me Chuzie, but that pic sure makes it look like that gear is already trashed. The light makes it look like there is a lot of grit in the area, the teeth are rough and worn, and it looks to be of softer bronze material. Which is strange, since it's the distributor gears for rollers that are usually bronze. Not the cam gear.

So yeah, it's hard to tell whatcha got there from that pic. It's a good clear one, just looking like the gear has already had a hard life.
Sure hope I'm completely wrong on that score!

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I think the pic makes it looks worse than it is. I will try again tomorrow. Gonna spray things down. Gotta pull the pan anyway to swap the pump shaft.

If, I can't ID it, I may do that expensive gear; seems like a logical choice. Thanks y'all.
 
Top