• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Never done this...wtrpump test by testing pressure in block

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
They may have changed in the 10 years since I sold them, but if not, I'd have to say yes they also perform well at lower rpm levels as well.

One of their main goals was low drag/ low power loss especially at the higher revs. Along with that was less cavitation, or at least cavitation at much higher rpm levels.

This in itself does not preclude lower rpm volume, but depending on any changes they may have made to impeller designs, I can't say for certain they're as good at lower rpm as say an Edelbrock or Flowkooler pump.
Which are not rated at as high an rpm or quite as low power loss as the Stewarts.

I'd have to re-post something from earlier to what 73az just said. I believe (but do not "know" for sure of course) that heat also builds pressure. So the pump is pushing fluid and building pressure, but heat is expanding the coolant and building what I was calling ambient pressure inside the system.
Water pressure and "air" pressure for lack of a better analogy.

Is that incorrect?

Paul
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Update tonight as the new Ford Exploder pump is in as of late last night so I'll "pressure test" it this afternoon. BTW, RD suggested again, as they did to me appr 7 yrs ago, that a new stock Ford pump is one of the best.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I think this is a notable comment from the Stewart page:



They make pumps made to spin at high RPM. But do they make high volume/pressure pumps for low rpm?
The Ranchero's 302 was a mild street & dune buggy tow engine. Came out of a '69 Econoline van owned by the owners of Titan Speed and was built specifically to tow their Boss 302 powered R.E.D. to the drag races on the West Coast. It rarely if ever saw the north side of 5k rpm, but did see a lot of sustained 3k-4k when pulling grades. Based in my experience with Stewart's Stage I pump and the radical change in cooling that it produced I'd say that their product does very well at lower rpm's.

I called the pressure increase from thermal expansion "Static Pressure" and the pressure increase from the pump "Dynamic Pressure" because the former will be there so long as the coolant is warm to hot regardless of engine running or not. The static pressure will vary depending on the coolant temperature. The dynamic pressure is only there when the pump is turning.
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Update with not so good news on this test...

SBF's and LS motors according to RD should have upwards of 25+ lbs of pressure with the engine's cooling system not up to operating temp, rpm at appr 2200 rpm, and the t-stat closed. Hook a pressure gauge up to the engine side of the t-stat so you are reading block pressure.

Well, I did this several times and I have exactly ZERO freaking lbs pressure. Two different gauges... once it gets up to temp and the system pressurizes I have cap pressure in the system....that's it. Both Ron and Bill the tech that works on many of the rigs in the shop are stumped right now... more later.

Crank is turning CW, wtrpump is turning CCW. No head gasket issue. Water shoots out of the tubes inside the radiator when the t-stat opens.

I'm putting it back together tomorrow... updated info: bubbles still behind t-stat...
 
Last edited:
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Sat. UPDATE... I tried checking pressure again two more times today...BINGO! Pressure...can't figure out why yesterday's test didn't work but maybe the block wasn't purged of air?

12 lbs of pressure at 2200 rpm- engine was cold, t-stat was closed, radiator cap was OFF

Drove to a buddy's place down the road who has my old 351 w/Exploder serp-same as mine. Hooked the gauge up to his rig, cold engine, removed the rad.cap and within 30 seconds he had 14lbs of pressure. He revved it up a couple of times and we watched the liquid filled gauge buzz up to 26 lbs or so at appr 3300 rpm.

I came back to my place, tried it again and buzzed it to 3500 rpm and had 24lbs pressure- still no cap, still a cold engine.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Cool that you finally got an expected result. Do you know what might have changed? Just the connection was leaking maybe?

Was just reminded of the waterless coolant I've seen used on some of the TV car shows (Wheeler Dealers originally, and now a PowerNation show) and wondered about your situation immediately.
I wonder if that stuff would help keep things cooler, and avoid any boilover issues when you do get into the higher temps.
They claim (I believe) that one of it's properties is to better contact the inner surfaces of the engine to promote better heat transfer. Kind of what we've been talking about.

Evans Waterless Coolant is the product. Haven't checked out their own website or claims yet, but wanted to put it out there for your consideration.
And because I have to go out and plant tomatoes before the daylight goes away completely!:-[

Paul
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
No changes other than the new wtrpump...everything else was the same on my rig...never figured out if there was air or not compressing in the block and not allowing an accurate test...Ron Davis did say it was important to get all the air out...
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Final update on this is...nothing. Fine when idling, can cruise down the freeway at 100F and be at 195F but if I'm snow wheeling at 5500rpm in deep snow with all 4 wheels locked and spinning at 45mph for several minutes at 20deg F I have to stop as the gauge will be 220F and climbing...

So my old 1976 Granada copper old school radiator just won't cool all the strrroker horses when it's working hard. I'm hoping to tube the front end this next winter when I go custom 36"x16" 1 1/4" tube alum. This I hope will cure all my issues. Inner wheel wells already have the SS screen ready for trimming and fitting...hate muddy engines! : )
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
FWIW I see now that Stewart does offer an Exploder application pump.

And, Brian, fwiw I have the freshened up 4 core high fin density "Desert Cooler" radiator out of my '79 3/4t SBC 400 powered 4x4 Suburban (with Baja pedigree!) that I plan to try making fit in the Bronc-up. The RS tank is at the headlight and the LS tank clears the outboard mounted PS box, but I can't get a good measurement on height yet. If it works it's going to be close. The existing BL is a requirement for it to work.
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Good luck Tom! It'll be tight fit but worth it....

I squeeeezed in this Granada radiator which is Core Size (in) approx:29-1/2 x 16-7/8 but I'm going to tube the front to make room for appr 38"x15"... I figure 560+ sq in ought to cool my needs in every situation compared to 360 sq in for a stock Bronco.

A stock early 2002 Duramax (I own one) radiator (using it because it's dimensions are so close to what I'll be using) radiator is 34x17 (578sq in) compared to a stock Bronco radiator (appr 360sq in). It cools fine when towing 17,000# in 100deg F heat.

Why do we think a stock 360sq in radiator which has appr 62% the cooling area of a Duramax radiator be able to adequately cool a strrroker powered Bronco when my engine has more torque and HP than a Duramax?

Obviously I'm not towing 17K gross, but...
It's not like I'm just using my Bronco hard for a short 1/4mile drag run or a light duty stop and go traffic use, or it heats up when the A/C goes on (I wish I had a/c)...like many others I work the engine hard and it needs to have adequate surface area to cool it and a way to ventilate all that hot air out of the engine compartment- hence the tubed front end with the screening.

That's my plan and since Tom mentioned that Stewart now has an Exploder pump, I might go that route too! Stewart makes a great product...
 
Last edited:

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
It's simple really, 360 in^2 is what fits a stock core support and it's a lot of work to break away from it.

Since the Bronc-up doesn't have one it makes it easier for me. I have pondered building fender liners from 1/8" black PE sheet once I have the front sorted out. They'll bolt to whatever engine/damper cage I end up with.
 

englewoodcowboy

Lick Creek Restorations
Joined
Jul 25, 2010
Messages
4,201
Ive read some replies with theories of pressure to force the water against the block and while it is loosely accurate in description it is far from accurate as to what and why. Pressure is created in the system for one reason, to raise e the boiling point of the water, higher pressure gets you higher boiling point. Think of it as a pressure cooker. Now you can add a water wetter product like from Royal Purple or the sort, it actually lubricates the surface of the water letting it come in better contact with the block rather than riding through on a cushion of steam. Now with the pumps, by design they are made to circulate, not really create pressure though they will simply due to the nature of what is going on. I am not saying the techs at RD are wrong with the test though this is the first tie I have heard of such a test, I would think you are having problems with the pump, specs could be off allowing cavitation which would reduce flow as well as you have other key components such as the T stat that could be acting up as well. Good luck in your quest.
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
I thought RD was a bit off on this test also... until I found out that NASCAR engines are pushing close to 45-50#'s pressure in their blocks only to increase the heat transfer and efficiency and cooling...so I tried it the test.

What englewoodcowboy said about the water wetter products... "it actually lubricates the surface of the water letting it come in better contact with the block rather than riding through on a cushion of steam" actually backs the need for higher pressure in the block because the "steam layer" so to speak will be thinner allowing the water to transfer the heat from the cylinders more efficiently like the sources I talked to said is needed.

I was a pump guy for almost a decade and have designed many water and irrigation systems after that fully understanding the differences btw auto apps and what I was doing but I consider myself fairly well versed in pump characteristics and what these guys are saying makes perfect sense but like Tom mentioned it's an engine design thing, not something the average Joe would ever get involved in therefore I believe that could be why we've never heard of this before...

Tom, that's why I'm using s/s irrigation screening because it allows air flow, keeps mud out and is available in many different screen opening sizes to keep crap from plugging impellers or plugging nozzles, etc... stainless looks ok too imo. Easily removeable for access IF ever needed (lol).
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Water has high surface tension, it's why with care you can over-fill a glass and have dome of water taller than the glass itself rather than it running down the side once completely full. Products like Water Wetter (A Redline Synth Oils Product) are in a class of agents called "Surfactants", they reduce the surface tension of the liquid they're designed to work with. Reducing the surface tension of water makes it 'wet out' better, make more/better contact with what ever surface. Most soaps will reduce the surface tension of water too, though I'm not going to recommend Dawn as a poor man's Water Wetter! This tension reduction is why you have to repeatedly rinse Gore-Tex materials after washing them. If you don't get all of the soap out they are not going to be water-proof.
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Is there anything that needs to be done to prevent gasket or other failures due to an increase in cooling system pressure?
 
OP
OP
nvrstuk

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,626
Loc.
PNW
Not that was shared with me. I did have one of those dang FelPro intake gaskets fail...but it wasn't from water pressure.

I got on my other favorite Ford engine site and others had the same issue with them... just run good steel core intake gaskets, NEVER use silicone RTV around the water ports ( this will spark another debate on how I've done this forever and never had a problem etc, but it's a problem now). Cometic makes intake gaskets now in different thicknesses and they work great. That's what I'm using now. They have a pretty good reputation for making quality products. : )

I should share a pic of what silicone does to the non-steel core gaskets...makes you a believer in never using RTV around the ports. If I still had the links I could show you a bunch more FELPRO gasket (non-steel inset) failures when using RTV around the water ports
 
Top