• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Help with Warn premium hub install

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
I'm installing my new Warn hubs and I've got a couple questions. I've got the driver side hub in, but there's a bolt and some sort of retainer on the driver side that's not on the passenger side.

Driver side with new hub and original bolt and retainer thingy:
0cabbf085210c58f184cc546a55feb99.jpg


Passenger side with stock hub assembly still in place (no bolt or retainer:
63053302e4fbbbecc2b5d6a678f7fbab.jpg


Are they supposed to be different or am I missing the bolt and retainer for the passenger side?


Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, Ford did not use the bolt in the end of the axle. Ford used a retaining ring in the groove, and you need a retaining ring pliers to take it on and off. I've heard of some replacement hubs which are too wide and cover over the retaining ring groove, so people use the bolt and washer to keep the axle from sliding in too much. Good luck
 

Teal68

Contributor
Bronco Guru
Joined
Mar 28, 2013
Messages
2,678
Loc.
Inlet Beach
Not a big deal that one of them is missing. Anyhow, you will not use those with the new lock outs from Warn.
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Hi, Ford did not use the bolt in the end of the axle. Ford used a retaining ring in the groove, and you need a retaining ring pliers to take it on and off. I've heard of some replacement hubs which are too wide and cover over the retaining ring groove, so people use the bolt and washer to keep the axle from sliding in too much. Good luck



I'm trying to understand why the PO would have used a bolt and washer on one side and a retaining ring on the other if the same hub was being used?


Sent from my iPhone using Tapatalk
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Not a big deal that one of them is missing. Anyhow, you will not use those with the new lock outs from Warn.



So what keeps the axles from moving in too far with the Warn lockouts?


Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, maybe you'll hear what other guys are doing. On my Bronco I have the retaining rings. If your grooves are exposed that's what I would do. Rings or bolts or ??? Good luck
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Ok, I think I figured out why there was a washer and bolt used on the driver side assembly and a snap ring on the passenger side. The axles are different diameter (at least the part that's exposed). Driver side is smaller and the snap ring is too big to fit it. But I can still see a groove in the axle for a ring.
e72c50ccb58fb3041d86a387ea1d8280.jpg


And here's the provided snap ring next to it:
2fa82f112a0ac86c840afdb45379807d.jpg


Now here's the passenger side again:
8d11dd21721541dd01b6a0757b6f27b0.jpg


And then with the new snap ring that appears to be the correct size:
ff244eb82468b66cc4576addb66e21e9.jpg


Why are they different sized? Sorry if this is obvious, but this is all foreign to me. I appreciate any direction/advice.

-Chris


Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the axles are the same diameter, it is the wrong snap ring, it is too big. All the hub parts are interchangeable left and right. Good luck
 

Nothing Special

Sr. Member
Joined
Nov 25, 2016
Messages
848
But he's showing the same snap ring next to both axle ends, so clearly the right and left axles aren't the same on his Bronco.

Looks to me like the driver's side outer axle was replaced or modified at some point. In fact what it looks like to me is that the end was turned down. I've always seen outer axles have the splines continue past the retaining ring grove, all the way to the end like shown on your passenger side. The driver's side doesn't have that, the axle is smaller out there.

I'd say if it's important to you to do the job right, get a new driver's side outer axle. Otherwise put it back together the same way it was.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, yes now I see the left side has been ground down. It probably got chewed up and mushroomed on something. It is still the wrong snap ring. Try the right side ring on the left. I would look for a snap ring that fits. Good luck
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
But he's showing the same snap ring next to both axle ends, so clearly the right and left axles aren't the same on his Bronco.



Looks to me like the driver's side outer axle was replaced or modified at some point. In fact what it looks like to me is that the end was turned down. I've always seen outer axles have the splines continue past the retaining ring grove, all the way to the end like shown on your passenger side. The driver's side doesn't have that, the axle is smaller out there.



I'd say if it's important to you to do the job right, get a new driver's side outer axle. Otherwise put it back together the same way it was.



Yes, you got it. There's no splines on the driver side.

I'd like to do it right, but I'm afraid of opening up a whole other can of worms. This is all foreign territory for me, so any insight into what will be involved in replacing that outer axle is much appreciated. I don't have any presses or anything fancy as far as my tools go (never opposed to buying new tools, but I don't want to spend $500 on tools to do this).




Sent from my iPhone using Tapatalk
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Hi, yes now I see the left side has been ground down. It probably got chewed up and mushroomed on something. It is still the wrong snap ring. Try the right side ring on the left. I would look for a snap ring that fits. Good luck



Thanks B RON CO. This sounds like the easiest option.

And if it makes a difference, I'm only going to be driving on the street, so I'm not concerned about any real nasties getting into the axles.

Oh, and the right side original snap ring is the same size as the ones that came with the new lockouts.


Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, OK the left side has been modified for some reason. The reality is that those splines on the tip don't matter. That is just the way they are made. What is important is that the splines are intact where they engage the aluminum hub locking part. I would pop the large out snap ring off, pull the inner hub locking part out and check out the splines on both parts. If the splines look good I wouldn't worry. Did you try the right side snap ring on the left side? I think that you need another snap ring that matches the right side. The left side ring is the wrong one. By the way, when you get it back together you should be able to spin the rotor with the hub locked and see the whole axle turn, and turn the front drive shaft. When the hub is unlocked the axle and drive shaft should sit still. Good luck
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Hi, OK the left side has been modified for some reason. The reality is that those splines on the tip don't matter. That is just the way they are made. What is important is that the splines are intact where they engage the aluminum hub locking part. I would pop the large out snap ring off, pull the inner hub locking part out and check out the splines on both parts. If the splines look good I wouldn't worry. Did you try the right side snap ring on the left side? I think that you need another snap ring that matches the right side. The left side ring is the wrong one. By the way, when you get it back together you should be able to spin the rotor with the hub locked and see the whole axle turn, and turn the front drive shaft. When the hub is unlocked the axle and drive shaft should sit still. Good luck



The splines are in good shape - the original hubs engaged without any issues (I replaced purely for cosmetics BC the originals are pretty beat up). And when I slid the new assembly on the left, it fit nice and tight.

I'll try taking the snap ring off the right and putting on the left to see if it fits. And I'll test everything after I get both sides on.

Appreciate the help.

-Chris


Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, if the Ford snap ring is too big for the modified left axle I would look forward a smaller one. I got a box of 1000 assorted snap rings for like $10 from Auto Zone. So now your left and right hubs have all the same parts, installed correctly, like identical twins, except for the grinded splines, right? Good luck
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
Hi, if the Ford snap ring is too big for the modified left axle I would look forward a smaller one. I got a box of 1000 assorted snap rings for like $10 from Auto Zone. So now your left and right hubs have all the same parts, installed correctly, like identical twins, except for the grinded splines, right? Good luck



Ok. Yes, they'll be identical once I get the right side done. I'll get some snap rings and find one that fits the left.


Sent from my iPhone using Tapatalk
 

Nothing Special

Sr. Member
Joined
Nov 25, 2016
Messages
848
....I'd like to do it right, but I'm afraid of opening up a whole other can of worms. This is all foreign territory for me, so any insight into what will be involved in replacing that outer axle is much appreciated. I don't have any presses or anything fancy as far as my tools go (never opposed to buying new tools, but I don't want to spend $500 on tools to do this).

As has been noted already, the missing splines aren't an issue. They only need to be cut there to let the hub slide over the retaining ring flange. Torque goes through the splines on the inner part of the hub.

The problem could come from the retaining ring not being able to do its job. If you use a ring small enough to work on the modified shaft it might not be big enough to support against the outer surface of the hub to keep the shaft from slipping in. Not being able to see the bolt / retainer plate in person I can't be sure that it's doing the job in the best way, but it would probably be easier to make a good retainer that way than to buy a retaining ring for the small axle to hold the standard size hub.

If you were to do it the "right" way it's not that hard (but not that cheap either). You need to take the wheel hub and spindle off, then the axle slides out. You might need a slide hammer or something like that for getting the spindle off. Supposedly you can borrow / rent what's needed from auto parts stores (I've made my own spindle puller so I can't speak to that very well). Then you need to buy a new outer axle and a new U-joint. You can remove / install a U-joint with nothing more than a vice and a big hammer. I've heard that a ball joint press makes it easier, but I haven't tried that.

But I should add that I don't mean to be implying that I think you ought to do it that way. If t were me I'd probably make sure I felt OK about how the bolt / retainer was doing it's job and stick with that.
 
OP
OP
Cvcoda

Cvcoda

Full Member
Joined
Sep 22, 2012
Messages
318
Loc.
Omaha, NE
As has been noted already, the missing splines aren't an issue. They only need to be cut there to let the hub slide over the retaining ring flange. Torque goes through the splines on the inner part of the hub.



The problem could come from the retaining ring not being able to do its job. If you use a ring small enough to work on the modified shaft it might not be big enough to support against the outer surface of the hub to keep the shaft from slipping in. Not being able to see the bolt / retainer plate in person I can't be sure that it's doing the job in the best way, but it would probably be easier to make a good retainer that way than to buy a retaining ring for the small axle to hold the standard size hub.



If you were to do it the "right" way it's not that hard (but not that cheap either). You need to take the wheel hub and spindle off, then the axle slides out. You might need a slide hammer or something like that for getting the spindle off. Supposedly you can borrow / rent what's needed from auto parts stores (I've made my own spindle puller so I can't speak to that very well). Then you need to buy a new outer axle and a new U-joint. You can remove / install a U-joint with nothing more than a vice and a big hammer. I've heard that a ball joint press makes it easier, but I haven't tried that.



But I should add that I don't mean to be implying that I think you ought to do it that way. If t were me I'd probably make sure I felt OK about how the bolt / retainer was doing it's job and stick with that.



Here's the retainer, looks solid and sturdy:
085f14a8b7e7e623d0cc221fc87f9395.jpg


I think as long as it fits under the new lockout cap, it should work as it did before.


Sent from my iPhone using Tapatalk
 
Top