• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Braking Issues

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Randy, I have a dual master set up, if you're interested. The masters are a bigger bore than what Wayne is talking about. But it will bolt right up to the Bronco firewall and pedal.

Mark
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
So dual master doesn't require a long pedal fabrication and bolts right to the firewall? That's even better. Mark, I'm definitely interested. Is it like the Jamar setup in Wayne's pic, just different bore? This would be great since the vacuum takes up so much room. The only issue I might have is the cross bar on the engine cage. It runs across the top of the firewall and would interfere with the Jamars in Wayne's rig.
 

Attachments

  • 20150709_164903.jpg
    20150709_164903.jpg
    110.4 KB · Views: 47

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
https://waynesbronco.shutterfly.com/377
There are a bunch of pics in there. You can see both masters are to the left of the original master mount hole and there is now a tube going through that hole. The cnc pedal has the steering shaft though it but was easy to do. Though if you had a stock type column, you could use 1 single master clutch pedal assembly on both sides and bolt one large pedal across to each one.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
http://pitstopusa.com/i-5063193-cnc...tVdLdrLc5dSlDOYhXpIzaaturS72BBue8vhoCqrDw_wcB

Imagine one on each side of the column with a wide pedal connecting them.
Another cool thing about dual master with a balance bar is you do not use a proportioning valve to limit rear pressure if needed. You can direct pedal force to one or the other. So when you take away from the rear to not lock them up, you also increase front pressure.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Thanks Wayne. That pedal is priced very reasonable as well for an engineered billet assembly. I'm definitely looking into that as well as seeing what Mark has.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
If you're running the D52's up front the first thing I'd do is swap to a dirt short oval track pad compound and try that. Pad life will likely be short and they may dust badly. Bed them properly. In my old days of road racing we "green-faded" everything, but refer to what the pad's mfg says to do. It isn't just about boiling out any remaining solvents left behind in the friction mat'l by the mfg process, it is also about creating a transfer layer on the rotors.

Regardless of what caliper piston area you have, per my old mentor for a manual system you're going to want a total system ratio in the 93:1 to 95:1 range. That is the ratio of the piston areas multiplied by the pedal's ratio. This only works with manual brakes, a booster alters everything about the formula. At below 93:1 the pedal is going to feel really firm and not stop all that well. Can go out to around 100:1, but you're well into the area of a mushy, uninspiring feeling pedal that actually will stop very well when you ask it to.

I run this 1.125" bore M/C: https://www.summitracing.com/parts/str-b3359ta with H-B and D52's on the stock front rotor with Exploder RDB's at the rear, and it stopped exceptionally well with 37's. Now that I've moved to metric 35's it is a little better. Front pads are CarQuest "Fleet" pads, what-ever those are. I've never thought all that much of being able to lock up the tires as braking effectiveness test so I've never tried. I have simulated a panic stop in the truck and am very comfortable with it's performance.

Be very exacting and careful in assembling and setting up a balance bar dual m/c system. They are the most frequent cause of brake problems in vehicles that use them. If they are not put together correctly, and adjusted correctly they can easily be a tech guy's biggest nightmare. They're enough of a problem that my old boss once commented that he'd rather not sell them at all because of how much time the tech guys spent getting them sorted out.

After all of that, recall that the weakest link in the whole system is the tire to ground friction. Early in my career I did a huge design exercise on a "Big Rotor" kit for Mustang II spindles and concluded that it would never work, the brake torque would shear the caliper bracket attaching bolts. Then Bill Wood stopped by my desk and when I showed him my calcs he pointed out that I'd assumed a perfect coefficient of friction between the tire and the ground when it rarely is better than .5 Right there I lost 50% of my brake torque! The lesson is that your tires can play a big role in braking performance and not to overlook them.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,223
I recall a pic of that system adapted to an H-B unit on a chase/pre-run OJB. No idea if I still have a copy of it or not.

Kevin Bunderson built a Chevy-powered OJB years ago that had a hydroboost adapted to the CNC pedal setup. CNC offered it as well at one time but I didn't see it on their website now.

Todd Z.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
If you're running the D52's up front the first thing I'd do is swap to a dirt short oval track pad compound and try that. Pad life will likely be short and they may dust badly. Bed them properly. In my old days of road racing we "green-faded" everything, but refer to what the pad's mfg says to do. It isn't just about boiling out any remaining solvents left behind in the friction mat'l by the mfg process, it is also about creating a transfer layer on the rotors.

Regardless of what caliper piston area you have, per my old mentor for a manual system you're going to want a total system ratio in the 93:1 to 95:1 range. That is the ratio of the piston areas multiplied by the pedal's ratio. This only works with manual brakes, a booster alters everything about the formula. At below 93:1 the pedal is going to feel really firm and not stop all that well. Can go out to around 100:1, but you're well into the area of a mushy, uninspiring feeling pedal that actually will stop very well when you ask it to.

I run this 1.125" bore M/C: https://www.summitracing.com/parts/str-b3359ta with H-B and D52's on the stock front rotor with Exploder RDB's at the rear, and it stopped exceptionally well with 37's. Now that I've moved to metric 35's it is a little better. Front pads are CarQuest "Fleet" pads, what-ever those are. I've never thought all that much of being able to lock up the tires as braking effectiveness test so I've never tried. I have simulated a panic stop in the truck and am very comfortable with it's performance.

Be very exacting and careful in assembling and setting up a balance bar dual m/c system. They are the most frequent cause of brake problems in vehicles that use them. If they are not put together correctly, and adjusted correctly they can easily be a tech guy's biggest nightmare. They're enough of a problem that my old boss once commented that he'd rather not sell them at all because of how much time the tech guys spent getting them sorted out.

After all of that, recall that the weakest link in the whole system is the tire to ground friction. Early in my career I did a huge design exercise on a "Big Rotor" kit for Mustang II spindles and concluded that it would never work, the brake torque would shear the caliper bracket attaching bolts. Then Bill Wood stopped by my desk and when I showed him my calcs he pointed out that I'd assumed a perfect coefficient of friction between the tire and the ground when it rarely is better than .5 Right there I lost 50% of my brake torque! The lesson is that your tires can play a big role in braking performance and not to overlook them.

That's great info ntsqd. They way you describe dual masters reminds me of VW dual carb nightmares! I want to be sure to get this right. I've already modified my pedal arm and I talked to Mark about his setup. I just need someone to be able to handle the fine tuning if I go that route. I'm still looking at Coach's electric setup also.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
It is not that balance bars are problematic and prone to change with age/weather/phase of the moon/acts of God/etc. like the ACVW dual carbs are. It is that unless assembled and set-up correctly their bias adjustment and resulting pedal can be very variable and inconsistent. Not a great thing in brakes.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
It still comes down to having the correct sized master cylinder/s to begin with. While power assist is helpful all to often they are used to cover up a ill designed brake system, If you cant lock up right now during a emergency stop then Id look at MC bore size before adding power. When you get it stopping like you want it manually then add power. The power really should only be used to further reduce pedal effort not so much to try and get the last few PSI out of your MC.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
That is a simplistic way to look at it, however it rarely works well out well done that way. The system needs to be designed as a whole. If a booster is planned it will alter what the correct m/c size will be and it usually has a pedal with a lower leverage ratio.
Additionally the type of booster and its original application can skew the ideal choices and ratios. If you look at the brakes from a grocery-getter and its sporty twin commonly the only part with a different p/n is the booster. That is how much tuning of the system can be done with the booster's boost curve.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
I think it would be in you best interest to utilize a non power set up. Most importantly with what you use your bronco for, such as mine, it's nice to know that if your engine dies, brakes are the same. Second I'm sure you could use the room assist takes up. 3rd it's one less thing to fail or leak.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Thanks again for the great info from everyone. I'm meeting Mark next week at the TDS run to pick up what he has, which is a double master, non power assist system. I can get rid of the whole vacuum setup I have, and the proportioning valve as well. I think it will actually simplify things in the brake dept. I just need to determine what size master bores I need after I verify what size calipers I have.
 
Top