Either way, that stud looks bent......
Tim
X2 on the bent stud
Either way, that stud looks bent......
Tim
just put the rocker back on and turn the engine over then you can watch the valve open and close or make a tool out of a piece of flat bar that you can put on the rocker stud and use to lever the valve down.
I'm more in agreement that you may have a sticking valve. I'm not totally on board that its todays gas as lead was not used to lube the valve guides valve seats yes but not the guides. I think its more of a issue with engines that don't get run for long periods of time. My 71 bends a pushrod or two every time I start it. I need to pull those heads as I'm out of spare pushrods.
On the other hand it could be the cam being a bit to big for the setup. Need to check and make sure the rocker arm is not touching the valve retainer when its fully open. Also make sure the rails are not touching the retainer or keepers at full lift. Might be a good idea to check pushrod length. aftermarket cams and rail rockers don't mix well. In the end Id consider either getting the heads setup for adjustable rockers or getting some aftermarket heads already setup. Not sure what the prices are nowadays but I was going to get some stock heads setup the way I wanted and the cost was only $1-200 below what aftermarkets cost and the aftermarkets are better out of the box than the stock heads would ever be even with a few hundred dollars more work into them.
If everything seems fine, put it back together and make sure the nuts are tightened properly. I wouldn't go any tighter than spec. The nuts can split if tightened too much.
If you have the same cylinder head as my truck, it's 3/8" studs that use 5/16" nuts. Double check to make sure before buying new nuts.
That's what happens when the cam comes up, and the pushrod is out of its socket because the rocker stayed down on the stuck valve - the pushrod is effectively too long, so that force goes against the stud & nut instead of the valve spring, and it stretches too little to see, but enough to relieve some of the torque....it had nothing like 20 ft lbs of torque on it...
That means it didn't come out of the head (or stretch) nearly enough to have been the root cause of the pushrod falling out-of-place. It had to be a sticky valve.I laid a machine tool straight edge across the top of both the adjacent studs and it doesn't appear to be any longer than those...
Stuck where? At the top of the cam lobe? That would simply have held the valve open, and the pushrod would have stayed in-place. At the bottom? That would have wiped the cam lobe, broken the camshaft between that lobe & the gear, or stopped the engine. But all of that pushrod's, rocker's, & valve's movement comes from the lifter - if the lifter sticks (anywhere), that pushrod/rocker/valve would have just stayed in-place. So that can't be what happened.even a stuck lifter could have caused this valve to jump track.
When it's NOT stuck, and the spring is in-place: too hard for you to do by hand, even with all your weight. If you use a spring compressor, and remove the keepers: the valve should drop into the cylinder under its own weight (assuming you aren't preventing it from doing so). With the spring & keepers in-place, tapping it with a medium-sized hammer (not a tack hammer, and not a BFH) should cause it to barely open & close faster than you can see. But it will look, sound, & feel distinctly different from tapping on a rocker stud, so you can compare it to that.How hard should it be to push the valve down?
That's what happens when the cam comes up, and the pushrod is out of its socket because the rocker stayed down on the stuck valve - the pushrod is effectively too long, so that force goes against the stud & nut instead of the valve spring, and it stretches too little to see, but enough to relieve some of the torque.That means it didn't come out of the head (or stretch) nearly enough to have been the root cause of the pushrod falling out-of-place. It had to be a sticky valve.Stuck where? At the top of the cam lobe? That would simply have held the valve open, and the pushrod would have stayed in-place. At the bottom? That would have wiped the cam lobe, broken the camshaft between that lobe & the gear, or stopped the engine. But all of that pushrod's, rocker's, & valve's movement comes from the lifter - if the lifter sticks (anywhere), that pushrod/rocker/valve would have just stayed in-place. So that can't be what happened.
It has to have been a stuck valve. Since the stud is in-position, the valve is the only thing that could have relieved enough of the spring's load from the pushrod for it to come out of its socket in the rocker.When it's NOT stuck, and the spring is in-place: too hard for you to do by hand, even with all your weight. If you use a spring compressor, and remove the keepers: the valve should drop into the cylinder under its own weight (assuming you aren't preventing it from doing so). With the spring & keepers in-place, tapping it with a medium-sized hammer (not a tack hammer, and not a BFH) should cause it to barely open & close faster than you can see. But it will look, sound, & feel distinctly different from tapping on a rocker stud, so you can compare it to that.
But if it's sticky, it will look, sound, & feel very similar to the stud; or it may delay closing long enough for you to notice that it didn't come back up at the same time as the hammer; or it may just stay down & each hammer tap will push it down slightly more, until there's enough spring compression to slam it shut.
Those tests will cost you NOTHING but a few minutes, and then you'll KNOW what happened. How you fix it is your choice, but a fuel additive is a cheap test while you're saving nickels for new heads.
Thanks guys for all the data, I've learned a lot here so far.. Looks like I've got positive stop studs, and when I removed the stud nut I'm thinking it had nothing like 20 ft lbs of torque on it? I measured the push rod at 6.883" and I know it has an "other that stock" cam but not sure just how aggressive.. The build sheet says a 275 Comp cam?? I do know that the rockers are Comp cam 1.6's but this truck has been full of surprises, some pleasant and some not do pleasant.. The push rod was leaned over but not rubbing the edge of the hole cast in the head.. I rolled the push rod on a very flat surface and it took off and seemed to roll very true with no wobble or humping.. I laid a machine tool straight edge across the top of both the adjacent studs and it doesn't appear to be any longer than those, but my eyes ain't what they use to be and had at least 3 different lights shinning on it at the time? When using a longer straight edge to span more studs, I get interference from the rocker arms I guess due to their position.. I'm pretty sure they are rail rockers but will post a pic shortly so maybe you guys can verify this.. The push rods are hollow so I'm assuming they are hydraulic? I'm leaning towards just pulling the other valve cover, removing the spark plugs and going through the procedure and torque the nuts to 20 ft/lbs and maybe put some blue thread locker on the studs (what could it hurt) .. Then again, maybe I should do the "Dry erase" marker method to verify push rod lengths simply so I will know what I have here regarding cam, heads, valve seats etc..? Thanks again..
You can get a bore scope and take a looksie inside the cylinder head. I believe they make attachments for cell phones now. They're kind of hard to get angled correctly, but it would enable you to check the valve through the spark plug hole.
My hope is that you're simply a victim of incorrect assembly and that you can put it back together and not worry.
Get rid of the staked nuts. used nuts or worn threads on the studs and they just don't hold.
http://www.jegs.com/p/Mr-Gasket/Mr-Gasket-Sure-Lock-Rocker-Arm-Nuts/748880/10002/-1
Crap!! ..Quick check but doesn't looks like they have them for 5/16"x24 nuts??Those look great !! Will have to check to make sure they will fit under the valve covers? Thanks
Hello Guys,
Thanks for all the data but I misspoke regarding the cam.. Seems it is actually a Comp Cam 274 kit.. I know the 6.88 push rod is the same but not sure on the springs? The one rod I measured was 6.883 so that part look OK? However, I will check it all tomorrow as I'm ready to rotate the engine.
BUT THE PLOT THICKENS ... While trying to locate some replacement rocker nuts I determined that the PO or someone installed a conversion kit to change them from positive stop studs to adjustable ones via the following Comp Cam kits...?
;D
http://www.compperformancegroupstor...e_Code=CC&Product_Code=4610-16&Category_Code=
http://www.compcams.com/catalog/COMP2012/pdf/COMP_Catalog_2012_59.pdf
That would explain why none of my rocker nuts are very tight, in fact you can rotate them with two fingers and a 3/8 drive ratchet .. Also I'm little concerned about one of the attachments recommendation "for high performance applications" replacing the rocker studs with threaded ones (which I don't think I have) in conjunction with push rod guide plates.. I'm not sure but I think either would require the heads to be removed which I'm not the least bit interested in doing.. I did a little digging around on some of the Mustang sites and found where people were using these kits with success but emphasized the need to use a half thread lock nuts?? I did have a moment today to check the valve with a bump bar and hammer and glad to report that it is not stuck.. Guess I'll find out more when I rotate the engine regarding the lifters tomorrow.. But as of right now,, I'm hoping that the nuts just backed off as per feed back from the Mustang guys??
Please note the pics of my rocker upon further inspection and you can see the really thick washer that exists.. I'm hoping I can get a height dimension on the valve when at base zero to verify nothing caught under the seat.. It has a Holly Truck Avenger carb with a 2" spacer so hoping I won't have to fool with those gaskets.. Will follow up tomorrow with more info and thanks to all for the excellent advise and support..
ribbits:
Hello Guys,
Thanks for all the data but I misspoke regarding the cam.. Seems it is actually a Comp Cam 274 kit.. I know the 6.88 push rod is the same but not sure on the springs?
Assuming the "274" is Comp Cam P/N: 31-246-3
Recommended valve springs are 986-16 & 987-16
986-16
► installed height of 1.750"
► coil bind height of 1.150"
► OD of Ø1.430
► 322 lbs. / inch spring rate
987-16
► installed height of 1.800"
► coil bind height of 1.150"
► OD of Ø1.430
► 370 lbs. / inch spring rate
Same pushrods as discussed for the "275" @ 6.881" & 6.900"
DJs74






