• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Stupid Windshield retaining knob question ...

ArkyJoe

New Member
Joined
Mar 16, 2017
Messages
22
Loc.
Arkansas
Anyone ever had the threads in the dash where the windshield knobs screws in strip out? Whats the remedy for that? Is there a nut in behind there that holds it?

I discovered why the previous owner kept the knob in the glovebox, the threads in the dash are stripped smooth out.
 

Big Fish

New Member
Joined
Jul 19, 2015
Messages
21
Loc.
Bakersfield
Anyone ever had the threads in the dash where the windshield knobs screws in strip out? Whats the remedy for that? Is there a nut in behind there that holds it?

I discovered why the previous owner kept the knob in the glovebox, the threads in the dash are stripped smooth out.

I think I would use what some call a fix a thread. It come with a over sized tap and a threaded coil back to the size you need. I have used them for a lot of different things in the past and had no problems. I think it may work.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I would try that first as well. Never had the issue, but have heard of others having it now and then. It's not that common, but maybe more and more now that rust gets involved.
Of course, you could just tap it for a larger bolt and use a standard hex head bolt like they did after '69. But the knobs are so much cooler!

Good luck. Hopefully someone has dealt with it before and will chime in with their experience.

Paul
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, before you go through the bigger job of fix a thread, or Hell coil, I would try a thread chaser or a tap. A thread chaser will roll back and restore threads, and a tap will cut new ones. Both will clear the original threaded hole. If there is still enough metal left you should be good. There is no nut, just a threaded section built as part of the windshield frame. If that doesn't work, you can go with Hell coil. Good luck
 

Dbarnes72

Sr. Member
Joined
Mar 18, 2009
Messages
643
Loc.
Eastern Wa.
There is no nut, just a threaded section built as part of the windshield frame. If that doesn't work, you can go with Hell coil. Good luck
I thought it was some kind of a captured nut in there but my Bronco is a couple thousand miles away so I can't go look right now. Either way it's a pain and I need to fix mine too.
 

jagbucket

Full Member
Joined
Aug 9, 2013
Messages
253
just did this and it is a captured nut . both of mine were broke off, a failed repair had been attempted and left half drilled when the capture framework part let go. actually not a nut but a threaded rectangular piece of steel . the one that was intact i was able to drill and re tap, the other i had to pry up against the frame and weld a plug weld to hold the piece while i drilled and tapped but of course now it will not move around as the weld is still holding but i was able to start the knob anyway .

point is, as it is a caputured nut if you get to aggressive with it it will break loose and then its much harder to deal with. Ether a larger bolt or retap the 3/8 use small increments in drill sizes and tap slowly forward and back the original idea of a threaded flat steel piece spreads the load out more than just a nut welded flush in the hole which i was considering. dosent look like much when finally done but its one more thing G' luck !
 
OP
OP
A

ArkyJoe

New Member
Joined
Mar 16, 2017
Messages
22
Loc.
Arkansas
Thanks for the info. I may tackle it when I pull the engine. I'll just pull the whole thing out and see what I've got.
 
Top