• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

braking system issues

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
I made a post a few days ago about how my passenger rear brake locks up and the rest of the wheels still spin when braking. I tried everything that was recommended and nothing remedied the situation. So I took my truck to a brake shop, they let me know that the back right tire is grabbing before everything else, and that simply adjusting it won't help, that the front of the car is doing 30% of the braking, when it should be doing 70%. I have disc in the front, and they said the back tires, lock up before the front pads even touch the rotors.

I have 0 idea on how to adjust when the front brakes grab, any ideas? I had my master cylinder checked, and apparently it is still good?

Possibly a proportioning valve from what I am reading, I have no idea where I would install that on my truck, I'm assuming it goes on the lines from the master cylinder? Also I would be looking to get one today, does auto zone or orally have them, or napa? I only seem to find it on summit.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
This sounds interesting. Can you post up every possible detail about your brakes from master cylinder, booster caliper etc?

If you remove the front tire are the pads in contact with the rotor on both side? If so they are ready to go.
If the rear brakes come on first:
1) The rear are getting pressure first (master cylinder or brake lines)
2) The rear are out of adjustment
3) There is air trapped in the calipers
 
OP
OP
M

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
This sounds interesting. Can you post up every possible detail about your brakes from master cylinder, booster caliper etc?

If you remove the front tire are the pads in contact with the rotor on both side? If so they are ready to go.
If the rear brakes come on first:
1) The rear are getting pressure first (master cylinder or brake lines)
2) The rear are out of adjustment
3) There is air trapped in the calipers

I am going to pick my truck up, and pull my front tires, will update ASAP.
1) this is definitely happening
2) they adjusted the rears, and the pedal feels stiff
3) would the pedal feel soft if that was the case?
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
Just follow the lines
One will head to the front and the other will head to the back on the frame rail
 

halfcab1969

Jr. Member
Joined
Mar 26, 2014
Messages
85
Loc.
Allentown
Someone please chime in if Im wrong but I think the larger of the two reservoirs go's to the front brakes reguardless of their position on the MC. I'm not at home right now or Id go out to the garage and look for you.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Make sure the brake line for the front brakes is on the mater cylinder port closest to the firewall. The brake line from the rear brakes is on the master cylinder furthest from the firewall. the brake lines come down from the master cylinder into a big brass H shaped switch. where the lines go into the H-Block the come out directly out the opposite side. on the opposite side make sure the lines go out where they are supposed to go and are not swapped by accident.
 

Attachments

  • ford combination valve.jpg
    ford combination valve.jpg
    59.6 KB · Views: 97
OP
OP
M

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
Not sure how to tell if it is reversed. Any one else with knowledge may?
 

Attachments

  • 6AA72B40-A38A-4869-823C-14D25CE1A6DD.jpg
    6AA72B40-A38A-4869-823C-14D25CE1A6DD.jpg
    93.6 KB · Views: 162
  • F9B59B16-0ABC-492B-BC7A-93D7B7EAA0FF.jpg
    F9B59B16-0ABC-492B-BC7A-93D7B7EAA0FF.jpg
    96.2 KB · Views: 113

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
With that master cylinder, you want the front brakes to connect to the rear port on the MC, the one with the larger reservoir, which is to account for pad wear. It looks like it connects to the front of the distribution block below, but it's hard to tell from that angle with all of the strain relief coils there.

As for proportioning valves, they are only for the rear brakes, as you always want to run 100% line pressure to the front brakes and then tune the rears to match. So while I don't know what the problem is, putting a prop valve in the front brake circuit is not the solution.
 

stevew

Bronco Guru
Joined
Jun 21, 2001
Messages
2,123
Loc.
Elliston Montana
You have a proportioning valve on there . The rear res. line goes to the front brakes as noted , the small res. to the rear brakes . Trace the lines & start from there .
 

rmk57

Sr. Member
Joined
Feb 24, 2016
Messages
580
Iv'e had seized rear wheel cylinders that would cause one or the other rear to lock up. Also check for a leaky rear wheel cylinder. Contaminated linings also make them grab and lock up to.
 
OP
OP
M

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
So the rear port on the master cylinder goes to the front of my proportioning valve, then another line comes out of the front of the proportioning vale down to a a connector then to the front brakes. The front port on the MC goes to the back of the proportioning valve, and a line exits the back to my rear brakes.

I have new wheel cylinders and spring kits
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Since that is an aftermarket proportioning/combination valve, I would also suspect it's at least part of the problem. I'm not really sure what happens to them, but I've heard of at least several that have had odd effects on braking.

Off subject a little, but if you were plumbing in a dedicated proportioning valve to reduce pressure to the rears, you would use a manually adjustable type and it would plumb into the rear line only. No effect on the front.
So just in case you end up going down that road, that is how it would connect.

Back to the fronts, did your brake shop let you know if the fronts were doing enough? Meaning, not that the rears were doing too much, but whether the fronts were even up to snuff?
Things like line pressure and such could have been measured if they'd bothered to check.

See that rubber boot thingy on the front edge of the prop valve? Under that boot is a brass tip that's part of what's called a "delay valve" (along with a couple of other names) and the official instructions state to pull out on the valve tip to hold it open when bleeding the front brakes. Not many people, including those at shops, bother to do this when bleeding.
Part of the reason is that most get away with it and it does not cause any trouble.
I'm wondering if yours is actually defective.

Some different ways to test it:
1. Pull it out against the spring and devise a way to keep it held out while driving.
There are small needle-nose vise-grips that can work. As well as a special tool designed to hold the tip out when servicing it.

2. You could pop the rubber cap off, put a socket on the hex head and literally unscrew and remove the valve. Then find a cap that can take it's place that will seal the fluid from leaking, but not block the flow inside.

3. This last method would be to disconnect the front lines from the prop valve entirely, and couple them together. Basically making it so that the master cylinder pushes fluid directly to the front brakes with out going through the brass block.
This last would completely eliminate any guesswork as to whether or not the valve is actually doing something to cause the front brakes to work less than they should.

Not sure what else to do to narrow this down. It's easy enough to put a new prop valve in to turn the rears down, but doing so is not dealing with the fact that the fronts are not doing what they're supposed to. It would only reduce the effectiveness of the rears by bringing them down into more of a balance with the fronts.
But if the fronts are just weak, you're weakening the rears to match. Doesn't sound like the best way to go just yet.

To be honest, I don't really understand their "the right tire is grabbing first, and that adjusting it won't help" statement. I mean, you told them that already!
I'd be interested to know how they came to the conclusion that the tire is grabbing first (?) or that adjustment would not help.

Good luck. Keep plugging away.

Paul
 
OP
OP
M

mduenas

Sr. Member
Joined
Dec 29, 2015
Messages
511
Loc.
Los Angeles
Thank you so much dirt donk. I’m going to figure out how to route around the proportioning valve, since my brake lines go right to it. Any input on that? What I should use? Also if I were to get a new proportioning valve, what would you recommend? What adjustable one? Since the Tom’s bronco parts one is the same one I have.

West coast broncos installed a centech wiring harness and didn’t install my brake warning light, I’m not sure how to wire that in, but is it rather important to have?
 
Last edited:

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
What you have is what I would call a "combination valve", as it has the metering valve up front (hold-off valve, delay valve, etc), brake balance switch in the middle and fixed proportioning valve in the rear. If the metering valve were to fail in a certain way, then it could restrict fluid/pressure to the front brakes and produce the type of symptoms you describe, weak front brakes. The purpose of the metering valve is to slow down the actuation of the front disc brakes in a disc/drum application such that the rear drums have time to engage first, which helps with minimizing dive and stopping straighter and safer, especially at high decel rates.

As for the rear brakes, they're both supplied from the same rear center brake hose, so they should be able to be adjusted to engage equally, assuming good parts. If not, then something else may be wrong back there.

While you could start replacing stuff and take the shotgun approach, it sure would be nice to figure out where the issue really is. If you had a brake pressure gauge, that would certainly make isolating the problem easier, but there are ways around that if you don't. Bypassing the combination valve with the front brake circuit is as easy as bending up some hard line and getting a couple of brass inverted flare coupler fittings...easy peasy.

I don't feel very strongly about the brake warning light one way or the other. While I like everything to work as Ford intended, at the end of the day, if my brake pedal feels weird while I'm driving my rig, the last thing I need is a dummy light telling me there's something wrong with my brakes. Since it's a pressure differential switch, it won't activate until something is seriously wrong, and the brake pedal will indicate that more directly IMHO.

Adjustable proportioning valves are typically 11-turn, infinitely adjustable cartridge valves that reduce the pressure to ~57% line pressure at some pressure set point. That set point is what is adjustable, not the 57% which is determined by the shape of the armature, so you move the set point up or down the pressure curve to set when the valve becomes active. Up to that pressure, the rear brakes receive 100% line pressure just like the fronts, whereas after that set pressure, the rear brakes only receive ~57% of what the fronts do above that. For example, if it's set at 200 PSI, then it would be 100/100, 200/200, 300/257, 400/314, etc.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yeah, it's the same style we sell as a standard proportioning valve. I think everybody sells them nowadays, and probably from the same three or four companies.
I've had defective ones before, including one that made the front brakes drag.
Maybe they'll replace it for you if you are diligent in your testing to make sure it could only be the prop valve?
Still sounds like at least part of the issue is something else though.

One thing about part of your issue, is your left/right problem with only one tire locking up. This type of issue at the rear can't be caused by anything forward of the hard lines on the axle housing. Nothing up front, from the soft hose to the frame, all the way up to the master cylinder can cause one side to brake harder than the other. That can only be done by some malfunctioning part, or inconsistent assembly or adjustment.
My point is that everything in front of the hose to the axle would effect both brakes equally. So the fact that only one wheel is locking up (as opposed to both) means the problem is only at the back axle.

Now, that's just the side-to-side issue. The problem with the rear having more power than the front is another matter.
For a proportioning valve, I like using an adjustable one in the rear system only. One like these: https://www.wildhorses4x4.com/category/Bronco-Proportioning-Valve effects only the rear.
But both equally, so you still have to deal with the one side braking harder than the other.

Do you still have the original H-block that was mounted to the frame? If so you can reinstall it, plumb the lines back to it, and then test the brakes. There is no restriction with an H-block to cause trouble. It's just a distribution block and the ports pass straight through.
They are still worth checking out before installing however. Water can get in and cause corrosion, as well as other things happening to them probably. Make sure it's perfectly good before installing.

Depending on the size of the fittings down at the current proportioning valve, there may be a simple threaded coupling that can mate the two halves together to bypass the prop valve. I just don't know the thread sizes or if there is such a thing as the coupler without you having to make one yourself.
Maybe someone has done this before. But the H-block would be the easiest to make work I would think. So if you have one, start there.

I suppose if you're not against spending a little more money (when does it stop?) you could have a hose made that runs from the master all the way down to the frame without stopping for any other components.

Maybe some others will come up with a simple solution. Probably someone's done it.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sorry, didn't see Apogee's response before adding mine. Sounds like we're on the same page though.

...West coast broncos installed a centech wiring harness and didn’t install my brake warning light, I’m not sure how to wire that in, but is it rather important to have?

You will have two wires from the new harness that will twist together and attach to the single wire coming out of the switch.
I'm with Apogee about it not being a critical lamp, but I also thing it's a handy thing to have.
The time it comes on is not necessarily as you're about to careen off the road though.:eek: When mine came on it was due to a small leak in the rear brake hose. Let me know something was up before, well, something was up.
Unfortunately I'm in a very well populated group, as after i fixed the leak I could never re-center the shuttle to get the light to go out!

Paul
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
You are getting good advice on what it could be but I think you need to narrow it down. I would verify the lines are routed correctly which it sounds like you did (disc brakes get the big reservoir).

I would take the rear line out of the master cylinder and plug it (you can get a plug online, Home Depot, Advance Auto etc). Then take it for a test drive carefully. If your front brakes are good they should stop you with no problem. If they work poorly I would suspect something else is wrong in the front (prop valve, line kink, air trapped, wrong or bad m/c). But if they work great you know your problem is in the rear half of the system. It could still be the prop valve or the m/c but at least you know your front half is solid.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
That's even better. Either way will isolate the issues, but Mark's idea of doing the work at the master cylinder instead is going to be much easier to work with. Kind of a pain sometimes, working around down between the engine, body and frame.

Paul
 
Top