• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Power Steering Box

BroncoMZ

New Member
Joined
Jun 1, 2016
Messages
36
Looking for a 4 turn power steering box and 4 mounting holes. My first choice was the PSC (SG630) but the cast housing is no longer available. Apparently ICON bought the remaining from PSC. PSC can only rebuild if you provide a core. I would be greatful for any recommendations or your experience with any of the power steering boxes out there for the Bronco
 
OP
OP
BroncoMZ

BroncoMZ

New Member
Joined
Jun 1, 2016
Messages
36
Most the boxes I've found online are 3 mounting hole configurations. Looking for a 4 mounting hole configuration. I'm mounting box to a Krawlers Edge frame with 4 holes in the frame rail.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Might check with the vendors to see if they are all like that. If so you could always source your own box that hasn't been modified yet. Another alternative may be to build a cage so to speak that mounts over the holes effectively covering and strengthening the box and mounting. I know some venders used to sell something similar for stock boxes a long time ago but I don't think they offer them any more. Honestly if the steering box stays tight the bigger hole shouldn't be a issue.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
What box specifically does Krawlers Edge say fits their frame?

Paul
 
OP
OP
BroncoMZ

BroncoMZ

New Member
Joined
Jun 1, 2016
Messages
36
What box specifically does Krawlers Edge say fits their frame?

Paul

PSC SG630 - which is no longer available from PSC

All the 4 bolt pattern boxes I’ve found have the rear 2 mounting holes slotted and the bottom hole very close to the flange edge.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I would choose a gearbox that is either easier to obtain and would seem to have a brighter future of availability, or is stronger and proven reliable. Which is/are likely one and the same box.
Then just modify the frame to fit the better choice of box. If needed...

First choice of what might be only two reasonable ones at this point would be the Delphi box everyone seems to be converting these days (like the Borgeson linked to above) that has the four mounting bolts. Even if the ones you have easy access to are already re-drilled in one or two holes.
The re-drill to an oblong shape to fit the stock Bronco hole alignment has not proven to be a weak link with anyone for the several years they've been used. The worst anyone has had to say is that the holes are ugly.

The other choice would be the 4x4x2 box we all love. Not because it's new and high tech, but because it's old, still readily available in many forms, and is super stout right from the factory.
The worst thing that happens to them (and this is actually fairly undesirable obviously) is that under some high-stress situations the end of the sector shaft can twist. This is always undesirable on a splined shaft of course, but overall it's still considered a heavy duty box and most here never experience a twisted shaft.
That said, I don't remember anyone complaining about a twisted sector shaft on their Delphi boxes.

And now that I think about it, I don't remember anyone who's done the conversion to 4x4x2 steering complaining about twisted sector shafts anymore either. Seemed it happened on old Ford trucks with big tires or that had been in accidents back in the day, but maybe when used on the lighter Broncos there isn't enough stress to cause the problem. Or the replacement shafts are just better?
Whatever the reason, I don't remember any comments here on the forums of damaged 4x4x2 boxes.

I'm only guessing at this next bit of course, but if you find a box that's designed to fit your holes and is unmodified, the overall cost in time and parts of putting it together is going to be just the same, if not more than the other stuff out there.
If there's a chance that anyone knows what the PSC box was based on and you can still source the originals, that would be great.
There were some comments awhile back that the 4-bolt box we sell looked like a core from a Nissan truck. Might consider looking there then too, for potential donors.

You might score something if you keep at the hunt. Those Toyota or Nissan boxes are another common alternative from a few years ago, and might even be a match to the KE frame holes.

Good luck. Either of the first two choices seem to be very stout. But I'd have to say that, spline twist notwithstanding, the 4x4x2 box would seem to be the choice if you are going big with tires and engine and like to have hard fun with your Bronco. Even with only it's three holes.
Unless you just don't like the idea of an extra hole possibly being visible, the 3-bolt boxes were good enough for 1-ton trucks and larger, so I'm guessing the same would hold true for a Bronco.

Paul
 
OP
OP
BroncoMZ

BroncoMZ

New Member
Joined
Jun 1, 2016
Messages
36
Paul (DirtDonk), thanks for the explanation and advise. Much appreciated!

I tried getting more info from PSC on the origin of the box...no luck other than the part number SG-630.

Made a dozen or so calls in the last several days. Thought I got lucky a few times, but eventually they all fell through. I'm going to look at all the suggestions/options and hopefully make a good decision on a PS box.
 
Top