• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Centech Install

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
I am wiring up my dash out of the Bronco. About ready to put it back in Bronco. I need a measurement for where to cut the hole in the passenger side firewall for the wiring harness on that side. I need size of hole and location. Also do I need to modify the driver side hole for the wiring harness?

Thanks
Will
 

SevenT

Contributor
Sr. Member
Joined
May 23, 2009
Messages
523
Loc.
Southern Colorado
Centech install

Smedley,

Measure the hole size for the harness leg that will go down the driver side of the front. Replicate that hole size and location for the passenger side and you should be good. The harness should be good for the factory size holes in the firewall.

v/r,

SevenT
 

pennyduke

Sr. Member
Joined
Jul 18, 2010
Messages
377
Loc.
Stafford
This is the best I could do. I hope this helps...
 

Attachments

  • IMG_1272.jpg
    IMG_1272.jpg
    81.1 KB · Views: 66
  • IMG_1273.jpg
    IMG_1273.jpg
    110.1 KB · Views: 69
  • IMG_1274.jpg
    IMG_1274.jpg
    147.8 KB · Views: 53
  • IMG_1275.jpg
    IMG_1275.jpg
    113.3 KB · Views: 63

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
....Measure the hole size for the harness leg that will go down the driver side of the front. Replicate that hole size and location for the passenger side and you should be good. The harness should be good for the factory size holes in the firewall.

Unfortunately this does not work for all EB's. Some (all?) '70 and older rigs use a smaller hole on the driver's side that needs to be opened up to work with the Centech grommet. I don't believe that is the case for '71 and later however.

But definitely measure it anyway, just to make sure. I had to cut the hole larger on a '69 and that "should" be the same as in '70. But you never know about these things!

And the Centech bushings/grommets are notorious for not fitting properly in those later holes. The instructions tell you what size hole to cut, but you should maybe wait for those that have had the problems and deal with them to chime in and tell you what they did.
Some actually cut off the Centech grommet and used a factory junkyard GM truck bushing instead. They are available new now I think as well.

But since you have the option of re-sizing while cutting a new hole, maybe do some pre-testing with some scrap metal panels to see if a smaller hole works better than the size Centech recommends.

Good luck. Glad you stopped in to ask before getting to this stage in the process. Too many issues have been had in the past to ignore. I got lucky and on the ones I did the grommets worked fine. But I do remember one of them being a little finicky and "almost" not working, so it will be good to see what others did to correct it before you cut your firewall.

Paul
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
Thanks for all of the input. Mine is a 70 and I have not yet check if the Dside will fit. In regards to location, has putting the Pside in the about the same location, as already offered, worked?

Will
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
That's interesting Pennyduke. So this is the '70 in your sig? A '70 with the passenger hole already stamped from the factory may have been a very late build '70 then?
Does your door post decal show the month of manufacture?

Did it also have the charcoal canister/evap system?

Thanks

Paul
 

pennyduke

Sr. Member
Joined
Jul 18, 2010
Messages
377
Loc.
Stafford
Sorry about that post, I was in a rush this morning and didn't mention that this was from a 74 that I just picked up. I will fix my sig.
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
OK. Hole on Dside is 1". Grommet is somewhere around 1 3/8 to 1 7/16 inches (both dside and pside). Obviously I need to make dside bigger. Then I will cut pside. How do I enlarge a 1" hole to 1 3/8" without a pilot bit? I tried that with the clutch rod hole and scratched up the floor boards.
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
OK. Hole on Dside is 1". Grommet is somewhere around 1 3/8 to 1 7/16 inches (both dside and pside). Obviously I need to make dside bigger. Then I will cut pside. How do I enlarge a 1" hole to 1 3/8" without a pilot bit? I tried that with the clutch rod hole and scratched up the floor boards.
Put a 2x4 on the other side, hold it tight

Sent from my SM-G920V using Tapatalk
 

pennyduke

Sr. Member
Joined
Jul 18, 2010
Messages
377
Loc.
Stafford
Can you cut a slit in the grommet and trim a little off to make it smaller? Will all the wires fit through the 1" hole that you already have in the firewall? Post some pic's if you can.
 

MidwestTexan

Jr. Member
Joined
Apr 1, 2018
Messages
92
I have a 70' and just installed the Centech harness in mine a couple of months ago. It's a super easy install although the instructions kinda suck... I sure wished I would have known about the 2x4 trick, that's a great idea.

As for the hole, my instructions said to drill a 1-3/8" hole on the D/P side which seemed a little small and I didn't have one. I used a 1-1/2" and it was perfect. I still had to use some force and a bit of lube to seat it although it's in there nice and tight. (that entire sentence just sounds wrong... haha)
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
Put a 2x4 on the other side, hold it tight

Sent from my SM-G920V using Tapatalk

You Sir, are a genius. screwed a 2 x 4 behind it and cut away with a hole saw. came out perfect.

Now I just need location of pside hole.

***Edit. I put the pside in about same location as dside. Will let you know how the harness fits. ***

Will
 
Last edited:
Top