• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

T18 Trans

KDW66

Jr. Member
Joined
Apr 30, 2008
Messages
76
Getting to the trans/transfer case on my 300 6 swap. The trans is a T18 and the tail shaft on is 12-3/4" long. I have a 6 cylinder adapter from my original engine/trans combo and its like 7".
Is there a shorter rear shaft to make this work? If so does the trans need to come apart? Should I just off it and find an NP 435?
Thanks in advance! Kerry
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Can you post up a pic just for reference? Is it a 4wd transmission originally, or 2wd?

Is the shaft like 8" of spline? Or is it just splined near the end?
Just wondering if you could cut off some of the shaft. Not the most common method, but even some 435 setups needed a half-inch or so of shaft cut down to fit the housing.

That long of a shaft is sounding like a 2wd version, or one from a divorced transfer case 4wd application.

Good luck.

Paul
 
OP
OP
KDW66

KDW66

Jr. Member
Joined
Apr 30, 2008
Messages
76
Two wheel drive from a 1991 F150. I haven't taken the outer housing off but I don't think its splined the whole length. Not sure this picture will post.
IMG_0049.jpg
Thanks
Kerry
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yeah, not sure how that works then, with such a long tailshaft. The kits we sell are supposedly for the 2wd version. Here are the instructions in case you haven't seen them yet: NP435/T18 Adapter.
The only thing I see mentioned is that some that have a threaded end on them may have to have that bit cut off. Nothing about cutting almost six inches off though.

The 6-cyl adapter housing is shorter than most however, so that is at least part of it. Though I think it's less than an inch shorter than a V8 housing. Still, the stock Bronco housings/adapters are not usually the ones you utilize. The A/A adapter is 7.5" long per the dimensions on the sheet.

I'm sure someone will know what's going on. Surprised nobody has chimed in yet in fact.

You can't post up images directly to your thread unless you are a contributor for 12 bucks a year. In lieu of that you can utilize your "garage" and other aspects of your User CP above. There are also online image hosting sites that are mostly free of charge, such as SuperMotors. You can use them and then link the images to your post.

Good luck on the trans install.

Paul
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
... Let me ask a couple of questions. How will you use your Bronco once finished.
If it'll be a street ride 85% of the time . Then I see no reason to jump to the NP435 . i HAVE THE NP435 & I love it in mine but Mine hasn't been unlocked from 4x4 in about 2 years. & 435 Is lower 1st gear.. I think like 6.54 compared to 4.59 or so. Someone will have the correct numbers.
If you'll use the T18 IN TOWN MOSTLY & THe T18 is the one Synchronized then I believe you'll like the T18 BETTER. tHAT LOW 1ST GEAR in Town is just a little slow.
... Now on of the ''T'' Transmissions is synchronized in 1st & the other is not. I've also got one of the T19's & I know it was 2wheel drive but from a Diesel Garman van
I'm watching this post because I'm not sure what I'll need to do if I ever get around to building this 68 Bronco i my garage. But I too have several of the 6 & V8 adapters I just don't know which one I'll need .
... Also DinkDonk Don't we both still have to have the 1inch thick aluminum adapter plate.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Pa..it's only the T-19 that is synchronized in 1st gear.

And...I would have expected a '91 pickup to have the T-19, not the T-18. They are interchangeable though...

The "deep" granny gear associated with the Ford T-18s is much rarer in T-19s; the rest are 4-something to one first gear.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
...Also DinkDonk Don't we both still have to have the 1inch thick aluminum adapter plate.

No idea on that Pa. Not even sure what adapter plate you're speaking of.
Does yours have one? Is it on the front of the trans or the back?

OK I DIDN'T KNOW ANY OF THE ''T'' had a lower 1st gear.
So I need to go see if mine is a 19, It has a tag.

One thing I've always done to every trans I work with is physically check the first gear ratio by simply putting the shifter into first, then spinning the input shaft while counting the output shaft turns.
This won't tell you it's an 18 or 19 maybe, but at least it'll confirm the ratio is as expected.

I learned that lesson after my first Ford 3.03 swap. The new replacement had a taller first gear than the original. Good thing I kept the old one to rebuild!
My replacement was a close ratio model with a very tall first! Almost like someone had replaced the normal first gear with the second gear of a 4-speed. Man, was that thing ever ugly in a heavy Bronco with a just-average gearing setup (4.11's and 32" tires). I really had to work the clutch to get it rolling. Really fantastic shift between 1 and 2 for once though!
But even in 4-low it was too tall.

Paul
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
.. Dink You may have just told me why I hated my 3speed in my Bronco when it was gas z& still a 3 speed.
... WHEN I 1ST BOUGHT my Bronco It had 3:54 & I put on 285/r16s. It was a V8 but man it shock on each take off . & Didn't run slow enough in 1st gear unless I was in low range.
.... So I swapped to the NP435
...................
... Now the Plate I'm talking about . We bought them from Toms I believe.
It's an Aluminum plate & we got the rear housing & the stub shafts . Each kit was about $425.00 As I recall.
...... Now that we've done both saps . 10 years ago .. I believe I could have used his rear housing & He could have used my rear housing .. But I could never get any information on what the rear stub shafts are from.
....... Now as far that aluminum plate . It was 1 inch thick & bolted to the rear of the Trans case ... Seems like it has bolt ''allen bolts'' that bolted through the plate & into the rear housing adaptor .. More bolts went around the outside of the plate & into the trans case.
... You could buy a plate for the A pattern or square pattern. Running Buddy had one trans & I had another.
.... AS I HAVE READ here .. the T18'S & 19 ALSO use those plates..
 
Top