• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Diving hard left during Braking

BruiserOutdoors

Bronco Guru
Joined
Aug 22, 2013
Messages
1,030
When braking, the bronco dives hard left. I had a Jeep TJ that used to do the same thing.

What could it be? I have already read that if one caliper brakes more than the other it will cause it to dive.... this makes sense but I don't think its my issue. Seems to brake fairly straight in reverse.


Also, the c4 automatic "clunks" into reverse. Could this be due to lack of fluid? Shifts into drive okay.




Rig is front disc, power brakes. Been sitting 20 some years


Advice much appreciated.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
The c4 clunking in reverse check that your idle is about 700 rpm in gear. Hold the brake and then shift in reverse. If the loud clunk is still there remove the rear drive shaft and check the splines and all the u-joints and the centering ball in the CV joint.

As for the brake dive check that the caliper isn't hung up or riding the knuckle if it is a chevy disc conversion. If the brakes are hood then check the trac bar bushings on both end.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
As for the brake dive check that the caliper isn't hung up or riding the knuckle if it is a chevy disc conversion. If the brakes are hood then check the trac bar bushings on both end.

Yep.....
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Bad right front caliper. Bad right rear wheel cylinder. Mis-adjusted rear brakes. Corroded brake lines from sitting for 20 years.

Better to fix this now before you hard brake into a head on collision.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Caliper clearance got me once. I had plenty when the pads were new but once they wore down a bit the caliper under pressure contacted the knuckle on one side. Every time it would pull left.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Pulling left = something wrong in the right front.
Caliper clearance is my first guess.
 

Glass Pony

Contributor
Bronco Guru
Joined
Feb 13, 2012
Messages
1,954
Loc.
Sussex County Delaware
I just had this issue a month ago. The culprit was a piece of debris got in the flex brake line to the passenger caliper where it connected to the hard line that runs along the axle.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the clunking noise is probably a bad u joint, which usually comes with a vibration as well. It could also be in the rear end. A quick hands on and visual check can help spot that.
As for the brakes, if it was my Bronco I wouldn't think twice before replacing everything, and cleaning and packing the front wheel bearings. 20 years is way too long to just try pads and calipers. Brake fluid absorbs moisture so there is a good chance there are internal parts stuck together.
I would make sure the brakes are in perfect working order for safeties sake, and I would get the best replacement parts from the best brand names. Most of us are keeping our Broncos a long time, so I wouldn't cheap out on the parts.
Good luck
 
Top