• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Which NP435

snick

Contributor
Full Member
Joined
Feb 5, 2015
Messages
158
I did search but couldn't find the answer. I'm trying to figure out which donor Ford truck np435 matches the bolt pattern on my I6 intermediate housing that I picked off of a 66 EB. I know that the Ford truck 2wd and 4wd np435 transmissions had slightly different bolt patterns. Which one matches the I6 intermediate adaptor?
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
You'd be looking for an NP435 with the square pattern. Regarding using the 6-cyl intermediate housing, you also need the adapter plate to use in conjunction with it. It's not a direct bolt on adapter for the NP435. Just one of two parts you need to make the conversion work without driveshaft modifications.

There is more info here

http://classicbroncos.com/tech/np435-4-speed-manual-transmission-guide
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Still need an adaptor (It's something like a 1" thick plate) to adapt an NP435 to the I6 tailshaft.

You want a Ford version of the 435.
28 spline on the output shaft.

The GM, Dodge, IH versions are all wrong.
The 31 spline (which I think is the newer ones?) would be wrong as well. As far as I know you have to pull the yoke to count the splines unless someone has a trick I don't know of.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Or if you find a married NP435/NP205 from a 4WD truck, you could run the trans and t-case as they are which gives you the beefier output shaft and t-case...might need to do something with the yokes though, as only a select few big broncos came with double-cardan shafts, and I'm pretty sure they were 1330 joints, not 1310.

Is this for the rig in your signature line or something else?
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
... I hate to High Jack this post BUT. I HAVE A 1980 300CID BRONCO .. It is a NP435 & I BELIEVE it's the NP205 also ... I really like the transfer case in it. It's shift from two wheel too 4 wheel while rolling down the pasture.
... That bit of info might help someone find the set up. I'm not sure when they changed to the T18 OR T19. & 205
... ONE OF THE 18'S OR 19'S HAS A SYNCHRONIZED 1ST GEAR. BUT IT a lot higher gear . LIKE 4:54 & THE NP435 IS LIKE 6:54 . & mY NUMBER MAYBE THE REVERSE.
bUT i BELIEVE IT'S 1ST GEAR.
 

bamabaja

Contributor
Sr. Member
Joined
Mar 25, 2012
Messages
729
Loc.
The Shoals
This might be some info.
 

Attachments

  • C4A30B74-A196-4730-A08D-DDFB0CA0E897.jpg
    C4A30B74-A196-4730-A08D-DDFB0CA0E897.jpg
    52.7 KB · Views: 54

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Or if you find a married NP435/NP205 from a 4WD truck, you could run the trans and t-case as they are which gives you the beefier output shaft and t-case...might need to do something with the yokes though, as only a select few big broncos came with double-cardan shafts, and I'm pretty sure they were 1330 joints, not 1310.

Is this for the rig in your signature line or something else?

The 205 can be had in 1310 U-joint, 1330 U-joint, 1310 CV, and 1330 CV flavors. The only factory application with 1310 CV on both outputs is the 1978 Bronco (79 has 1330 CVs). But you are also going to loose a lot of low range. The 205 is only a 2:1 low. It is also a BIG transfer case. It does fit in the Bronco frame rail, just barely. The 205 is also getting harder to find. You can't use just any 205, only the Ford versions had the driver's side drop. Other 4x4s doing engine swaps also go after the Ford 205 for the driver's side drop as well. At one time they were very available and cheap. The price has gone up a bit, but the availability has really shrunk. Those old dent side Fords are not being scrapped out like they once were. They are either being saved or are already gone. I can remember going through a pick a part yard and there were 30 of them in a line, last year I needed some parts and it took 3 yards to find one dent side and it was in the "premium lot" where parts cost more. Old iron is getting old enough it is getting collectable.
 
Top