• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Full Width Tire/Wheel/Extensions

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
What’s the ultimate combination? I have a chassis project that I’m thinking of going full width with but want to see what the options are. I would prefer something that keeps the tires under the fender extension.

I’d like to go as wide as possible but not let the tires hang out. Pics would be great.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
TOO many variables for us to tell you what you want... like asking "what color should I paint this Bronco"?

Legality matter to you?

Street only

Mud only

DD?

Do you run tight trails?

Do you like mud, rocks, water thrown all over your rig? Sides, top, inside too (running trail doors).

Wide is more stable-does thst matter with your intended use

Do you like the look-is it worth it??

Lots more personal taste stuff

You won't find any FW axles that fit under a Bronco's fenders. .and what do you mean by extensions?-flares???

My advice. Start looking at dozens and dozens of Bronco pics and see what look you like.
 

frenchy

Contributor
Bronco Guru
Joined
Nov 29, 2005
Messages
1,043
unless your planning on running 1 tons you might as well stay with stock if you want to keep them under the Bronco. Thats a big can of worms you opened with that question.
IMO....
frenchy
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I kind of swerved into an answer. Because my axle is a '76-'77, I had to limit the back spacing to 3.75". The wheel is a 15X8", so the out board side of the tire is 2" further out. This put the edge of the tire just inside the edge of the flares. I too think tires protruding beyond the sides of the truck just looks bad. I see no reason to swap in '78-'79 axles to get what you want. I'm assuming that's what you mean by full width. In reality EB axles are full width for an EB.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
I would think the front hubs would be the limiting factor up front, assuming you don't want those to extend further out than the wheels/tires. Measure lip to lip on your fenders, subtract your hub to hub dimension, and that tells you how much wider you can go unless I'm missing something.

Going wider just to run deeper offset wheels doesn't really gain you anything, does it? I can see the handling and geometry advantages if you were fabricating an IFS/IRS setup, but it feels like we're missing some information with respect to the goals for your build.

Tobin
 

idus25

Contributor
Full Member
Joined
Oct 30, 2014
Messages
213
Loc.
St. Louis
Not sure I understand "fender extension".

This is my 76. 1st pic is 77 F150 in front with Stock 76 rear. Wheels are 17 x 8 TR BLocks with 3.75 back spacing. 35 x 12.50 BFG MTR. The rear sticks out just to the fender flare.

2nd, the rear, with a 79 F150 on. Same wheels, same back spacing, same tires.
 

Attachments

  • IMG_4559.jpg
    IMG_4559.jpg
    129.4 KB · Views: 147
  • bronco rear.jpg
    bronco rear.jpg
    120.4 KB · Views: 167
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
TOO many variables for us to tell you what you want... like asking "what color should I paint this Bronco"?

Legality matter to you?

Street only

Mud only

DD?

Do you run tight trails?

Do you like mud, rocks, water thrown all over your rig? Sides, top, inside too (running trail doors).

Wide is more stable-does thst matter with your intended use

Do you like the look-is it worth it??

Lots more personal taste stuff

You won't find any FW axles that fit under a Bronco's fenders. .and what do you mean by extensions?-flares???

My advice. Start looking at dozens and dozens of Bronco pics and see what look you like.

Street mostly but some offroad. I don't think that have any limitations in SD for how far out they can run tires, judging by how many I see daily that look ridiculous. We also have no inspections.

I want them to be tucked under and thought that maybe the Zombie Apocolypse type would take care of that. I am also not afraid of cutting the axles down if need be.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I figured that it might handle better on the street, and I could run skinny tires to get through the snow when the time comes. I would also move the rear axle back to center it in the wheel well.

Its just the way I do things. I never just do what everyone else is doing. I like to make it function but improve it if it's possible. If removing the Dana 30 front end and installing a Dana 44 does the trick then fine. I just thought that while I am down to the bare chassis this would be the time to experiment.

I was also wondering if the Zombie fender extensions would be enough to cover up the tires so that it doesn't look goofy.
 

redfishtony

Full Member
Joined
Apr 17, 2008
Messages
209
Loc.
Thomasville GA
idus25, I want to verify that the pics you posted are of a 77 f150 axle in the front and a 79 in the rear? I'm working on a d44 out of a 76 f150 right now and was thinking of cutting it down but I really like the look of the tires out the 2 inches. Thanks, TW
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Fender flares come in a lot of different flavors. Ranging from just a little over uncut to pretty darn wide. I have not kept up with what wide ones exist these days. So start with picking flares.

How tall of a tire do you plan on running? There are a lot of choices and limitations. Speaking of limitations, a trail monster will have different limitations than a mall cruiser.

As asked before, what local legal restrictions do you have?

So many factors, and even if we knew exactly what you were after, there are still a dozen ways to deal with it.

Now for different width axles vs wheel spacers, and even deep dish wheels. You can start getting into some ugly front ends. As in the tire doesn't necessarly pivot anymore, it swings. Think about a tire sticking out past the pivot points. The tire swings to the back as it is turned in that direction and swings forward when turned the other way. That stick is also a lever loading up wheel bearings and ball joints. Extra leverage.

Another option that I never see people do, cut the body and widen it. There are so many options.

I've had one vehicle that has had full width axles under it. I didn't like it. Any tiny puddle and the tires splashed mud up the whole body side. You could not drive with an arm on the window ledge, the tires would flick rocks/sand up at it. I am sure flares would have helped but I don't think it would have completely fixed it.

Don't know if you can find a set of those balloon fenders, they were from a California custom Bronco builder that I can't think of right now. I think they folded. (The company, not the fenders)
 

idus25

Contributor
Full Member
Joined
Oct 30, 2014
Messages
213
Loc.
St. Louis
idus25, I want to verify that the pics you posted are of a 77 f150 axle in the front and a 79 in the rear? I'm working on a d44 out of a 76 f150 right now and was thinking of cutting it down but I really like the look of the tires out the 2 inches. Thanks, TW

Yes Sir. '77 F150 front & a '79 F150 in the rear. They stick out more than that. Nearly half the tire sticks out with 3.75 backspace.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
This would be mostly for the street, but doing a little 4 wheeling once in awhile. There aren't many steep areas around here, so I don't need a rock crawler.

I was thinking of running a tire under a stock height if possible, and would prefer not going up any more than a 2.5" lift. What size tire fits under a wide axle with the Zombie Apocolypse fender extension? Are there other options that would keep the tire from throwing debris up the side of the truck?

What are the PROS of running full width axles?
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Send us a pic of this "Zombie extension" ypu keep mentioning.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
If it's for mostly street with mild off roading. You also dont want much lift and plan on close to stock tires why go thru the expense and headache of trying to fit full widths? The stock axles should be fine with maybe a 44 swap up front. If you want more strength for piece of mind get a set of moly axles to go in em.
 
Top