• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Nv3550 and t-case

pennyduke

Sr. Member
Joined
Jul 18, 2010
Messages
377
Loc.
Stafford
I just got a good deal on a Nv3550 and Transfer Case still attached. Is it possible to use it like it is or use my old D20? Which route would be more efficient and cost effective if I can use the one attached? Thanks
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
If the new transfer case is another Bronco D20 you can just use it. The only issue is are you putting it into your 74 or your 70? Pre-early 73 was a "T" case. Late 73 and onward was a "J" case. It matters to your transfer case shifter. If its the opposite for your year then you'll have to switch your transfer case shifter, get a twin stick, or switch to your current D20. Easiest way to tell is the shift rail linkage. Look at the metal plate between the shift rails.

J: https://www.tomsbroncoparts.com/pages/wp-content/uploads/2010/09/bronco-dana-20-j-shift-grinder.jpg

T: https://classicbroncos.com/dana20/diagrams/figure03.jpg
 

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
I just got a good deal on a Nv3550 and Transfer Case still attached. Is it possible to use it like it is or use my old D20? Which route would be more efficient and cost effective if I can use the one attached? Thanks

I have thought about that quite a bit. With the value of these things increasing, and people seeming to like a pretty traditional recipe it may not be wise to swap to the NP 231. You would most likely need driveshaft work and a slip yoke eliminator and of course custom mounts etc.

But you would also get true shift on the fly and a lower range crawl ratio. I have thought about it, and from a truly pragmatic perspective it could work pretty well.
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
I have thought about that quite a bit. With the value of these things increasing, and people seeming to like a pretty traditional recipe it may not be wise to swap to the NP 231. You would most likely need driveshaft work and a slip yoke eliminator and of course custom mounts etc.

But you would also get true shift on the fly and a lower range crawl ratio. I have thought about it, and from a truly pragmatic perspective it could work pretty well.

If you're swapping out a stock 3 speed, stock drive shafts work fine. You will need to make a cross member mount for is as EB70 noted.
 
OP
OP
P

pennyduke

Sr. Member
Joined
Jul 18, 2010
Messages
377
Loc.
Stafford
Thanks guys, This is going in a 69 with no lift. I do think I need to do a body lift for the conversion so im going to get started on that first. I will do some more research and see which way is best. I do like the idea of keeping it together just how it was in the Heep.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
If the transfer case is a NP 231 I don't think it will fit between the frame rails.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
If the transfer case is the NP241OR...it will also not fit between the frame rails. But it does come with a fixed yokes, 6 pinion planetary, and 4:1 gears.

And then you have to figure out the speedometer. NV3550 + NP231J, or NP241OR will be a tone ring with a magnetic pickup.

you can run a clocking ring and rotate the t-case down...but that makes it vulnerable to the rocks. Or you can notch the frame. Or you can shift the drivetrain to the right another 3/4 inch.

Or you can buy the adapter for the Dana 20...which is where most everybody else ends up.
 
Top