• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

5.0 temperature and gauge cluster question

zacraig04

New Member
Joined
Jun 11, 2015
Messages
45
Loc.
Memphis TN
Hey everyone - I have a 66 Bronco with the 5.0 explorer (96) conversion. I finally have everything up and running, except for my original gauge cluster. I have read many threads talking about the voltage regulators and other issues regarding the gauge, but a lot of it is over my head discussing Ohms readings and other things. My voltage regulator on the back of the gauge looks pretty warn out, so I think the first thing I need to do is find a new regulator?

More background: I have converted to a painless body harness, and have modified the Explorer engine and transmission harnesses per the EFI guy. My questions are:

1. Is there a simple way for me to run a separate engine temp gauge? I would like to have this just to ease my mind that I am not running the engine hot. But I assume the ECT is controlled by the computer?

2. As for as getting the original gauge cluster to work, any advice on getting the speedometer up and running? Im running the 4r70 trans and harness. What wires am I looking for to hook to the tach?

Thank you in advance of the help...

Zac
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Hey everyone - I have a 66 Bronco with the 5.0 explorer (96) conversion. I finally have everything up and running, except for my original gauge cluster. I have read many threads talking about the voltage regulators and other issues regarding the gauge, but a lot of it is over my head discussing Ohms readings and other things. My voltage regulator on the back of the gauge looks pretty warn out, so I think the first thing I need to do is find a new regulator?

More background: I have converted to a painless body harness, and have modified the Explorer engine and transmission harnesses per the EFI guy. My questions are:

1. Is there a simple way for me to run a separate engine temp gauge? I would like to have this just to ease my mind that I am not running the engine hot. But I assume the ECT is controlled by the computer?

2. As for as getting the original gauge cluster to work, any advice on getting the speedometer up and running? Im running the 4r70 trans and harness. What wires am I looking for to hook to the tach?

Thank you in advance of the help...

Zac

1. Yes you can run an aftermarket temp gauge. You can use the signal wire in your harness or run a new wire.

Do you have the correct engine temp sensor in your block, there is an early and late style which will change you temp readings.

The ECT is another sensor that the ECU uses to see what temp the engine is running at. Usually found in a port on the cooling tubes.

2. D20 transfer case? use the standard speedo-cable that is plugged into the D20. It may not be long enough now. Not sure how you would pull a signal from the OSS in the 4R70W? I usually get the longer speedo cable from the Vendors (Tom's) that comes with a Mustang style VSS and that plugs into the d20. You will have to figure out what drive gear to use. And I use that signal from the VSS to drive a Tach.
 
OP
OP
Z

zacraig04

New Member
Joined
Jun 11, 2015
Messages
45
Loc.
Memphis TN
1. Yes you can run an aftermarket temp gauge. You can use the signal wire in your harness or run a new wire.

Do you have the correct engine temp sensor in your block, there is an early and late style which will change you temp readings.

The ECT is another sensor that the ECU uses to see what temp the engine is running at. Usually found in a port on the cooling tubes.

2. D20 transfer case? use the standard speedo-cable that is plugged into the D20. It may not be long enough now. Not sure how you would pull a signal from the OSS in the 4R70W? I usually get the longer speedo cable from the Vendors (Tom's) that comes with a Mustang style VSS and that plugs into the d20. You will have to figure out what drive gear to use. And I use that signal from the VSS to drive a Tach.

1. Thank you for the info. I am not sure how to check what style temp sensor I have. I am running the 96 explorer stock configuration? I bought a mechanical water temperature gauge, but was afraid to remove the Explorer sending unit and cause a problem with the computer?

2. Yes on the D20 case. I will look into the TBP longer speedo cable. Thanks again.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, if any of the three gauges, fuel, temp, or oil pressure works, the IVR is definitely working and you don't need to change it. To test the IVR all you need is a test light. Everyone should learn how to do simple tests with a test light. Good luck
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
1. Thank you for the info. I am not sure how to check what style temp sensor I have. I am running the 96 explorer stock configuration? I bought a mechanical water temperature gauge, but was afraid to remove the Explorer sending unit and cause a problem with the computer?

2. Yes on the D20 case. I will look into the TBP longer speedo cable. Thanks again.

1. There are two temp sending units. One for the gauge, located in the lower intake, Drivers side front. The second is for the ECU located in the cooling tubes as they screw into the lower intake Passenger side front.
 
OP
OP
Z

zacraig04

New Member
Joined
Jun 11, 2015
Messages
45
Loc.
Memphis TN
1. There are two temp sending units. One for the gauge, located in the lower intake, Drivers side front. The second is for the ECU located in the cooling tubes as they screw into the lower intake Passenger side front.

Thank you guys. That's what I needed.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
You can't share a sending unit between 2 gauges. That includes a gauge and a computer. The way an electrical gauge works (or the computer) adding a second gauge will cause errors due to how the voltage drop through the resistor happens.

Just in case that thought crossed your mind.
 
Top