• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Windshield Lower Frame Seal - installation Q

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
Years ago (early 2014) I picked up at windshield lower frame seal from Wild Horses (it's the Dennis Carpenter part).

I'm guessing that the "bead" part sits furthest from the hinge (see pic below). What I'm curious about is how the hole for the wiper wiring is sealed.

One way would be to remove the wiring (which sounds horrible), punch a hole in the new seal, and reinstall with weatherstripping adhesive. I've also thought about cutting the new seal into two pieces (I have 3-4 inches extra which is nice), putting 1/2 a hole in the end of each, and reinstall with the adhesive.

My plan is to set this up so the windshield can be lowered when needed. Advice is much appreciated, thank you for your help.
 

Attachments

  • PXL_20201020_012608330.jpg
    PXL_20201020_012608330.jpg
    119.1 KB · Views: 602

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The factory installed the seal with the round hollow side closest to the hinge pin. By installing the seal correctly the wiring hole will be sealed too. A little body putty between the hole and the end of the seal would insure the seal, but I don't think it's needed.
 
OP
OP
jerry

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
Like this?

The factory installed the seal with the round hollow side closest to the hinge pin. By installing the seal correctly the wiring hole will be sealed too. A little body putty between the hole and the end of the seal would insure the seal, but I don't think it's needed.

jckkys,

Thank you for your input. So you mean oriented like the photos below?

That would make sense - then I'd create a notch for the hole, and add some sealer for good measure.
 

Attachments

  • PXL_20201022_013440372.jpg
    PXL_20201022_013440372.jpg
    95.7 KB · Views: 468
  • PXL_20201022_013511668.jpg
    PXL_20201022_013511668.jpg
    108.6 KB · Views: 489

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Sounds like a good plan. The factory put body putty between the hinge and the cowl and also between the hinge and the windshield frame. Then they spot welded the hinge to both. The seal was simply placed near the hinge pin and then they erected the windshield frame. Experience tells me that was good enough.
 

Hultzger

Jr. Member
Joined
Sep 4, 2018
Messages
106
Loc.
Martinez
Jerry I’m about to install a new seal on my Bronco. The PO used a flat stick on seal and the water just pours through.

What sealant did y’all use?

Interesting difference between where your wiper wire is routed than mine.

6a6b3c38f7ef6e87d03b5483859355a4.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Is yours a '66 by any chance Hultzger? I've seen flat seals before too, but not often and I'm in no way sure they were factory early style or not, as all the ones I've ever used myself were the type you have with the bulge on one end.
It was my experience I thought that all the factory seals with the bulge had it to the rear, unlike what jckkys was saying. But knowing that he's an original owner of his lends more weight to his experience.

And I've never seen any sealer from the factory either, but jckkys' is a '77 so maybe that's something they started doing a few years after they got rid of the vacuum wipers also? And maybe also changed the orientation of the gasket? Or maybe that was the proper way, and the ones I've seen were installed incorrectly instead.

My '71 did not have any kind of putty or sealant, but I've long been a proponent of adding something to the gap there. Since I never plan to fold the windshield down under normal use that would not cause me any distress.
The trouble would come whenever I wanted to do some work in that area. Maybe that putty idea is the beast way after all. Silicone sealer would just glue it all together and make it hard to work with a few years later.

Paul
 

Hultzger

Jr. Member
Joined
Sep 4, 2018
Messages
106
Loc.
Martinez
Paul,

It a ‘67 and based on how easy the old seal came off and the fact that it looks like the windshield was removed for a repaint at some point (notice the shiny screws).

4346f58f2cf6b2590fd6a25713618755.jpg


I’ll probably drop a bead of silicon on the bottom surface so the seal stays in place.

Rick
 
OP
OP
jerry

jerry

Contributor
Sr. Member
Joined
Jan 28, 2002
Messages
778
Loc.
Bakersfield, CA
Jerry I’m about to install a new seal on my Bronco. The PO used a flat stick on seal and the water just pours through.

What sealant did y’all use?

Interesting difference between where your wiper wire is routed than mine.

6a6b3c38f7ef6e87d03b5483859355a4.jpg

That is interesting. Mine is a 70 with an October 69 build date, and the old seal looked really flat without much of a bead. I haven't used any sealant because it seems as if that bead towards the hinge should block all water through that route, with any "overflow" directed out the sides.

I'm test fitting everything as i install my door seals, before I bolt the hard top down I may use some weatherstripping adhesive to hold it in place.

Appreciate you sharing your pics and your thoughts!
 

reamer

Contributor
Bronco Guru
Joined
Mar 20, 2008
Messages
1,268
Stay away from silicone, use a "seam sealer" silicone actually promotes
rust.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
on my 1974 factory had the bead at the hinge side. they gooped dum dum around the wiring hole.
 
Top