• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

67 fire wall holes

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
Working on the wiring and wondering what these holes are for on the upper drivers side fire wall

Also not sure if I have the harness coming out of the lower drivers side firewall into the engine bay is in the correct location? If so what is the other hole below it for.
Thanks
 

Attachments

  • DCB3455B-57DC-44C8-9144-4014877621FF.jpg
    DCB3455B-57DC-44C8-9144-4014877621FF.jpg
    59.8 KB · Views: 129
  • 3E767641-6D66-406B-9D07-CBB249608E3A.jpg
    3E767641-6D66-406B-9D07-CBB249608E3A.jpg
    43 KB · Views: 126

doran4x

Contributor
Sr. Member
Joined
Dec 31, 2004
Messages
405
The two holes are for the throttle bracket. The one in the center is electrical, I believe.


Sent from my iPhone using Tapatalk
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Some rigs have this single 3/4 hole and others don't. Usually, later models have it for the Dura-spark wires, at least my 77 did.

Use it for the wires that run inside for your EFI conversion. Too late to weld it up it looks like...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
And I hope very much that your original wiring is in very good shape for it's age. With the new EFI setup going in you're going to need all the cooperation out of the old stuff that you can get.

If you haven't read tons about it already, at the very least make sure to add extra grounds where they never were from the factory on EB's. Up-size the battery and starter cables and upgrade to a modern alternator if you have not already.
You need all the power and cleanliness you can get from your old system to help the new system work to it's potential.

Paul
 
OP
OP
papy

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
Some rigs have this single 3/4 hole and others don't. Usually, later models have it for the Dura-spark wires, at least my 77 did.

Use it for the wires that run inside for your EFI conversion. Too late to weld it up it looks like...

sorry which hole are you suggesting -the lower one by the EBrake assembly or the one beside the explorer ECU?
thanks
 
OP
OP
papy

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
And I hope very much that your original wiring is in very good shape for it's age. With the new EFI setup going in you're going to need all the cooperation out of the old stuff that you can get.

If you haven't read tons about it already, at the very least make sure to add extra grounds where they never were from the factory on EB's. Up-size the battery and starter cables and upgrade to a modern alternator if you have not already.
You need all the power and cleanliness you can get from your old system to help the new system work to it's potential.

Paul

surprisingly the original harness is in very good shape. no concerns with it being brittle or any signs corrosion. very rare i know lol. i had a buddy check/test the harness however if it turns out giving me issues then i will move forward with a new harness from one of our venders.
thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sounds like you'll be ok for the most part then. Still you need to add multiple grounds to enhance what was already a barely sufficient grounding scheme to begin with.
But the wires themselves sound like they may just serve you well and you can avoid the big re-wire project.
Maybe...;D

That big hole facing the middle is an odd one. It's on "most" Broncos, but has had different uses over the years. A friend of ours has a '68 (That's Brian's rig Doug) that actually has his main power wire run through there with no signs of it ever having been in one of the two main firewall plugs like normal. Very strange!
If it was not done at the factory, I have no idea how someone did such a clean job of re-routing it. It was very sloppy in the hole though, with no hint of a grommet or reducer visible. Making me think it was not factory wire routing, but the hole was definitely factory.

My '71 does not have one, while my '68 does. But on the '68 I'm not sure if it's factory or if 904Bronco put it there for the re-wire?
I can't really see it behind all the EFI stuff, so can't tell if it's exactly in the factory location or if it was added.

Paul
Paul
 
OP
OP
papy

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
Sounds like you'll be ok for the most part then. Still you need to add multiple grounds to enhance what was already a barely sufficient grounding scheme to begin with.
But the wires themselves sound like they may just serve you well and you can avoid the big re-wire project.
Maybe...;D

That big hole facing the middle is an odd one. It's on "most" Broncos, but has had different uses over the years. A friend of ours has a '68 (That's Brian's rig Doug) that actually has his main power wire run through there with no signs of it ever having been in one of the two main firewall plugs like normal. Very strange!
If it was not done at the factory, I have no idea how someone did such a clean job of re-routing it. It was very sloppy in the hole though, with no hint of a grommet or reducer visible. Making me think it was not factory wire routing, but the hole was definitely factory.

My '71 does not have one, while my '68 does. But on the '68 I'm not sure if it's factory or if 904Bronco put it there for the re-wire?
I can't really see it behind all the EFI stuff, so can't tell if it's exactly in the factory location or if it was added.

Paul
Paul


sounds like another bronco " i wonder why" thing lol. no one bronco is the same right? even from the factory...

well hey don't jinx my wiring harness now! joking joking - i guess we shall wait to see what happens when it comes time to turn the key.

JP
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
sorry which hole are you suggesting -the lower one by the EBrake assembly or the one beside the explorer ECU?
thanks

By the ECU...

The 69 I am working on now had three holes. I welded up two of them and left one for the EFI cab wires.
And Paul's 68...
And my former 71
 

Attachments

  • IMG_20201104_164428302-2.jpg
    IMG_20201104_164428302-2.jpg
    149.3 KB · Views: 67
  • DSCN1198.jpg
    DSCN1198.jpg
    99.7 KB · Views: 99
  • DSCN3759.jpg
    DSCN3759.jpg
    70.9 KB · Views: 100
OP
OP
papy

papy

Contributor
Sr. Member
Joined
Jun 13, 2012
Messages
905
By the ECU...

The 69 I am working on now had three holes. I welded up two of them and left one for the EFI cab wires.
And Paul's 68...
And my former 71

right on thank you for sending the pics. i appreciate it
cheers
 

Ratclge

Jr. Member
Joined
Mar 8, 2018
Messages
92
firewall holes

If u dont want to weld up the holes go to an electrical supply store and get rubber or plastic hole plugs,they look pretty neat.
 

chuckyb

Contributor
Sr. Member
Joined
Oct 25, 2016
Messages
960
In Papy’s first picture that single hole on the left was originally for the manual choke cable.
 
Top