• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

76 won't start, help!

dmplatt

Jr. Member
Joined
Oct 21, 2014
Messages
134
Stock 302 in a 76, non-duraspark ignition (I got a few leftovers from 75). Stock carb, literally stock everything as far as I know. Electric choke. The truck gets driven weekly during the summer, but the fall and winter it's less frequent. It's always been a bit of a slow starter - after sitting for a week or more it cranks a while before starting, sometimes takes more than one try. But not this time...

Hadn't been driven in a few weeks, tried to start it, cranked and cranked, but no start. Just getting back to it and the same issue. Now it's cranking slow from trying to start it which I'll remedy with a hook up to one of the other cars when I try again.

I've never tried to diagnose a problem like this so looking for some direction.

Fuel - pretty sure it's getting fuel
Air - adjusting the choke plate during cranking didn't seem to matter
Spark - not sure how to test this...
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
Pull a sparkplug out and lay it on the engine or exhaust manifold so it’s grounded and have somebody crank the engine. You might need to make it dark around the spark plug you will see a spark
Or just on on to it and crank the engine. Haaa
 

ared77

Contributor
Bronco Guru
Joined
Apr 21, 2013
Messages
3,178
1) look down into carb throat and move linkage, do you see a stream of gas as you are moving throttle? Yes, move on to #2 No, out of gas, plugged filter or line, bad fuel pump. (If no gas is present, the shot of starting fluid should make it start for a few seconds...to prove it's a fuel issue)

2) Check for spark by pulling a plug and grounding it then watching for spark while someone turns key to "crank" engine. Spark present? Check for timing issue, maybe a stretched timing chain. No spark? Pull distributor cap and be sure rotor is turning when engine is cranked. Could also be a failed coil, loose or broken wire, etc.

Good luck, and let us know!

Norm
 
OP
OP
dmplatt

dmplatt

Jr. Member
Joined
Oct 21, 2014
Messages
134
Ok, I tried with a little starting fluid and it tries to start but dies immediately and even after 3 tries won't stay started.

Should I see fuel when I move the throttle even when it isn't cranking or do I need someone to crank it while I do that?
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
The accelerator pump should squirt fuel into the bowls each time the throttle is moved, regardless of the engine being cranked. You should be able to see the fuel clearly squirting looking down into the carb and moving the throttle by hand.
 

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
sounds like no fuel, might have a bad fuel pump... you could disconnect the line and run it to a bucket and see if its pumping fuel into the bucket....or what justino said...a little easier ...lol
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Just out of curiosity what ignition setup do you have if you removed the DuraSpark?
The harder to start/ more starter cranking time is common now with the " new blend " of so called gasoline. The gas evaporates from the fuel bowls.
 
OP
OP
dmplatt

dmplatt

Jr. Member
Joined
Oct 21, 2014
Messages
134
It's the smaller diameter distributor.

I only put non-ethanol gas into the truck.

I'll check the fuel again tomorrow afternoon.
 

TNcowboy

Full Member
Joined
Aug 29, 2019
Messages
220
Sounds like a fuel issue

Have you checked...or just change..the fuel filter? Probably the most likely culprit
 

MikeCon

Full Member
Joined
Apr 7, 2019
Messages
276
Replaced battery cables with new heavier ones. Also new battery
Made all the difference.weak spark=,slow start..
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Fresh gas with fuel stabilizer, ie water dispersion, in the gas?

Temps drop, water condensing falls to bottom of tank.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The size of the distributor cap says nothing about the type of transistor amplifier. Duraspark II ignition is defined by the module. The '76 Duraspark II had small distributor caps. In '77 on they had big caps.
All carburetors that sit for extended periods have empty float bowls. Gas evaporates. Usually, the engine needs to be cranked till the pump fills the bowl before the engine can fire. Starting fluid is ether and not good for engines. A couple oz. of gasoline injected in the bowl vent to fill the bowl before cranking will let the engine start immediately.
By looking down the choke chimney while holding the choke plate open; move the throttle lever and look for fuel squirting from the nozzles. If so, go to the spark.
I stick a screw driver in the distributor end of the high voltage coil wire. Let the screw driver shaft sit near any metal surface. Crank the engine and look for the spark. I've seen the Duraspark II arc 3/4".
Everyone needs a battery charger, especially in the winter. Even if you have AAA. When the battery is charged, there is a spark, and fuel is in the float bowl, but it still won't start, we can start looking for another diagnoses.
 
OP
OP
dmplatt

dmplatt

Jr. Member
Joined
Oct 21, 2014
Messages
134
@jckkys thanks for the education - this is why I came here! I always assumed it was a switch at the same time as the size of the cap. I am also under the impression that most 76s came with the larger diameter cap maybe I'm wrong there too...

In any case. No fuel in the carb when I manually move the throttle, so that's something. So fuel filter next... and I'll add some more gas because although I know it has some it may not be a ton.

I didn't spot a fuel filter up near the carb so I'll have to go crawl under and locate it.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The fuel pump has to pull gas all the way from the tank to the carb then fill the bowl. It's all uphill. That's with a perfectly good pump, filter, and carb. The little nipple on top of the float bowl that points at the choke housing is a perfect place to inject a couple oz. of gas into the carb. Even if none of the parts mentioned don't work that will run the engine a few seconds. One or two of these will fill the fuel line, pump, filter, and float bowl. Don't go replacing parts unless they were individually tested and failed. The fuel filter is the easiest. Just blow through it. If you can't blow air through it's bad. Otherwise put it back on the carb. The fuel pump is tested as rydog suggested. The engine will crank faster if you loosen or remove the plugs to test the pump. The diaphragm and one way valves in the pump dry out and don't work as well as when fuel is always in it.
 

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
The fuel filter is the easiest. Just blow through it. If you can't blow air through it's bad. Otherwise put it back on the carb. The fuel pump is tested as rydog suggested. The engine will crank faster if you loosen or remove the plugs to test the pump. The diaphragm and one way valves in the pump dry out and don't work as well as when fuel is always in it.

I will admit, publicly for the first time, that a few months ago I put in a new few fliter backwards. Yes, the inlet and outlet are clearly marked, but you know...

It let fuel flow through and ran. But if I let it sit for a day, wouldn't start. After a couple days of pouring gas into the carb to get it going, I got the bring idea to check and see if *by some chance* I put in the fuel filter backwards. I did.

So I second check the simple things first.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The OP said everything is original. The OE filter is screwed into the front of the float bowl so it's hard to install backwards. I've only had to replace one of these in 55+ yrs. of driving. They aren't very big, but I have had no problems with them. Filters need to be placed between the pump and the carb. So inline filters are good and can be installed backwards. We don't know that dmplatt has found the pump/filter to not flow fuel to the carb. That would be the first test needed to diagnose the problem.
 
OP
OP
dmplatt

dmplatt

Jr. Member
Joined
Oct 21, 2014
Messages
134
Update: I dumped some fuel into the carb, said a prayer or something like it, turned the key. It sputtered a bit but then started right up! Sounds like @jckkys (and others) was right on - just struggling to get fuel all the way from the tank.

Oh did I mention it's at least 20 degrees warmer today than when I was trying the other day? I have a feeling that may have been a factor too.

Thanks all for the help, now any suggestions how to avoid this particular issue? Drive it more comes to mind :) but what other ways to help this?
 

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
The OE filter is screwed into the front of the float bowl so it's hard to install backwards.

Agreed. In fact, impossible. But when there’s another between pump and that filter, like my setup, very possible. Or clogged.
 
Top