• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Pcv/vent

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
I have a new 408 Blueprint engine. It has holes in both valve covers for oil filler/paver. I have a filler on one side and a vent in the other. The vent I have has a small filter like a k&n. I am getting a lot of oil blowing out the vent and also around the oil filler. So much so that it gets thrown in the header and smokes.
Should I install a pcv valve and take the hose to an intake port? I currently have the intake port plugged. I do not have a air filter with a pcv port. I could buy a bulkhead fitting and do it that way rather than an intake port.
Not sure why I have so much blow by but I do drive it hard.
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
i asked this question a few weeks ago. Using valve covers with oil baffles over the vent holes helped some.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Should I install a pcv valve and take the hose to an intake port?

Yes and no. A PCV valve needs full manifold vacuum from the base of your carb. Don't run it into a intake runner, and the base of
the air filter wouldn't provide enough vacuum to open the PCV valve. It needs full manifold vacuum from the base of your carb or
throttle body if that's what it came with. Without one your oil will slowly turn to sludge.

Replace the oil fill cap with a PCV valve and run the hose to the base of your carb or TBI. The side with the small K&N type filter can
be used as your oil fill port. That's exactly what I do, pull small filter, add oil, put filter back in.

Support the site and become a contributor and upload some pictures of that 450 hp beast. We like pictures :)

https://classicbroncos.com/forums/showthread.php?t=34373
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I have a new 408 Blueprint engine.
I have a filler on one side and a vent in the other.
Not sure why I have so much blow by but I do drive it hard.

First, if you want your new motor to last as long as possible, you absolutely positively must install a PCV system. For now, you should be changing the oil probably twice as often as you would think. Maybe more. Or install a working PCV system.
It's not just for smog, it's for the life of the engine.

And you basically answered your own question above too.
1. New engine. 2. Driven hard. 3. No PCV.
There you have it in a nutshell. A classic recipe for oil blowing out the top.

What kind of filler do you have? A cap, or an extension filler like the more modern versions of the engine? If you can use a cap you should have one of these factory types: https://www.wildhorses4x4.com/product/Oil_Cap_with_PCV_Elbow_Black/bronco_Valve_Covers
Remove the elbow and insert a PCV valve instead. Might take a different grommet, but I'm not sure. This style pictured is the '71 and later cap, but fitted as if it's a '70 or earlier for some reason.
It's meant to be fitted to the driver's side valve cover and the passenger side gets just the grommet and elbow with a tube to the air filter housing. Since you say you don't have a correct filter housing you can continue to use your pleated filter/breather setup. It will still ooze slightly, but with luck it will be reduced by 80% or more.

Only the valve has vacuum connected to it. The breather side is only a filtered air intake to allow clean air into the engine while the valve is sucking the bad air out.
The vacuum line should be plumbed to a common-plenum fitting. In other words, at the base of the carb, or a spacer under the carb, or directly into the intake manifold under the carb. Never into a single runner like you can get away with for most other vacuum accessories.

If you have any normal air cleaner housing you should be able to make your own breather fitting to go to an elbow instead. Sometimes there are off-the-shelf parts, sometimes you have to punt.

What type of valve covers are they? Got pics?

Paul
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Yeah, but you explained it much more detail, which we all appreciate!

Scott
 

trekgurl

Full Member
Joined
Dec 7, 2006
Messages
315
Can of worms, “opened”

First, if you want your new motor to last as long as possible, you absolutely positively must install a PCV system. For now, you should be changing the oil probably twice as often as you would think.

Maybe more. Or install a working PCV system.
It's not just for smog, it's for the life of the engine.
And you basically answered your own question above too.
1. New engine. 2. Driven hard. 3. No PCV.

There you have it in a nutshell. A classic recipe for oil blowing out the top.
What kind of filler do you have? A cap, or an extension filler like the more modern versions of the engine? If you can use a cap you should have one of these factory types:
https://www.wildhorses4x4.com/product/Oil_Cap_with_PCV_Elbow_Black/bronco_Valve_Covers
Remove the elbow and insert a PCV valve instead. Might take a different grommet, but I'm not sure. This style pictured is the '71 and later cap, but fitted as if it's a '70 or earlier for some reason.

It's meant to be fitted to the driver's side valve cover and the passenger side gets just the grommet and elbow with a tube to the air filter housing. Since you say you don't have a correct filter housing you can continue to use your pleated filter/breather setup. It will still ooze slightly, but with luck it will be reduced by 80% or more.

Only the valve has vacuum connected to it. The breather side is only a filtered air intake to allow clean air into the engine while the valve is sucking the bad air out.

The vacuum line should be plumbed to a common-plenum fitting. In other words, at the base of the carb, or a spacer under the carb, or directly into the intake manifold under the carb. Never into a single runner like you can get away with for most other vacuum accessories.

If you have any normal air cleaner housing you should be able to make your own breather fitting to go to an elbow instead. Sometimes there are off-the-shelf parts, sometimes you have to punt.

What type of valve covers are they? Got pics?
Paul

So, I been reading this and I’ve been fiddling with this oil “blowing” out some.

I have this old Autolite Emission’s manual PDF http://www.mustangtek.com/Library6/PDF/1969AutoliteEmissionControl.pdf and was looking at section 7. Principals of Operation, Crankcase Emission Control. I only included a few pages trying to understand this some.

I put on the new valve covers and my PVC valve is on the passenger side and the drivers side has one of taller tube filters. I’m still getting oil blowing out some, 1969, 302- old engine, driven somewhat hard, and PVC valve. Before I got the new valve cover’s, I had PVC on the passenger side and oil cap/ hose, similar to the oil cap you list above and hose was routed to air cleaner. I still got "some" oil build up in the air cleaner but it did not seem to be as bad as with the "new valve cover "tube filter" etc.

I kinda want to go back to that setup as I’m getting oil down on my headers too. My engine has most of( if not all) the original plumbing as when I bought it, as I have not change much.

So how is the PVC system supposed to be set up? I’ve included some of the pages from that PDF. Can you diagram it?
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
First, if you want your new motor to last as long as possible, you absolutely positively must install a PCV system. For now, you should be changing the oil probably twice as often as you would think.

And this is because (seriously asking)???
The only difference I see is the crankcase gases aren't "pulled" from the engine and put back in the cylinders at idle or very low rpm. How much difference does this make vs just letting it vent? I run breathers in both valve covers since no emissions required. Ive asked about PCV at several shows and at some events up here in Ohio, and for offroad and hot rodding it's always unanimous to not run a PCV, I've heard it called an uncontrolled vacuum leak on numerous occasions. I can see making the case for changing the oil more frequent without the burnt gases being pulled from the crankcase though.
Certainly not disputing your explanation Paul, I value it, looking for more info all the time.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I put on the new valve covers and my PVC valve is on the passenger side and the drivers side has one of taller tube filters. I’m still getting oil blowing out some, 1969, 302- old engine, driven somewhat hard, and PVC valve.
So how is the PVC system supposed to be set up? I’ve included some of the pages from that PDF. Can you diagram it?

Looks like yours is pretty much correct, but there might be some flaws that allow it to work, but still let oil vapors collect up at a place they can leak from.

Where is the vacuum line attached? Carburetor base? Intake manifold? Assuming carb, but can't really see the detail.
The main culprit might be the valve covers themselves. There might not be sufficient baffling on the passenger side, which would allow the valve to suck more oil than necessary. Does your engine use much oil?
The driver's side has the fill, which is usually not baffled at all. So if you have any blowby at all, or if the valve is not sucking hard enough, then the vapors travel right up that "chimney" and condense in the filter medium until it drips.
Some of them have a basic baffle tube, in the form of an extension that runs down in-between a couple of the rocker arms to get it closer to the head and out of the vapors supposedly. But I think we've found that in many cases this is not enough. The low-profile filler cap on the other hand has additional baffling build in, which seems to help a lot.
Still not a cure for an old tired engine, if that's what you're experiencing. But better.

While the engine is running pull the valve out of the cover and see just how much suckage it has and how it effects the idle while it's out. While doing this also note how much smoke/vapor, if any, is coming out of the valve cover.

To be clear, it does not matter which side of a V8 the valve is, and which side gets the clean air return to the crankcase. Works the same way either way, and it's mostly convenience and plumbing options that dictate which side you put the valve on. The later model 5.0 engines put the PCV valve in the back of the intake manifold right over the rocker valley. But those early ones were prone to sucking a lot of oil up into the upper intake manifold too. Hence the HUGE baffle plate that went into later models including the Explorer.

Anyway, check to see how it's doing, and maybe peek down inside the covers while they're open to see if there is anything to let the vapors collect and condense down inside before they get up into the area that allows it to drip down outside.
Oh, and I guess another test would be to remove the filter only, while the valve is in place and the engine idling. If a piece of lightweight paper can get sucked down on to the opening and you still have fumes coming out, you have at least a little excessive blowby.
If it does not suck the paper down, your valve is not sucking very hard. Not sure just how much this should show up, and I've never personally done it (never needed to) but it seems like it would give a little indication of the health of the system.
Paul
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
We still don't know what you have for an air/fuel mixer. Throttle body injection or carburetor? What make and model? The PVC connection is different depending on the answers to these questions. The crank case air has oil mist, raw fuel, and the products of combustion including water. These are impurities that effect the A/F mixture, so you want them evenly distributed to all the cylinders. Carburetors that have a PVC port inject this air just below the primary throttle shaft on both sides. It's a mistake to dump it anywhere you have full manifold vacuum. The WH elbow referenced is usually called a breather elbow that's designed route clean air from the air cleaner to replace the air removed by the PVC hopefully on the opposite side of the engine.
 

trekgurl

Full Member
Joined
Dec 7, 2006
Messages
315
thanks Paul,,,, definitely have an old engine, but seems to run really good. It does seem to use some oil.. (doesn't smoke or leak) and I seem to notice that if I'm running on the interstate for a while (around 70-75 mph). I'll trace the PVC plumbing and do some checking when the weather breaks some.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
[ And now that we're talking about power, I think that's what Engine Masters at MotorTrend should check next. They've done a test on alternators, water pumps, cooling fans and restrictive air filters, they should test an engine with a PCV after a vented engine just to see if there is in fact any loss at all.
I'd watch that episode for sure!

Paul ]


Me too Paul.
Love this sort of myth busting.

I have developed theories and proven them out through testing every day for the last 31 years.
Its my life and work.

When Engine Masters runs their dyno testing on engines that they are making changes too, they have combined my work with my love....
I'm a starry eyed kid when watching that show.
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
There's even a $100 custom tunable PCV valve that can be fine-tuned to work with any specific engine with any range of performance modifications.



I run one of the tunable PCV's on my carbureted 331 with COMP Cams Xtreme Energy 268H camshaft and roller rockers. The idle is rough and vacuum bounces rapidly between 11 and 14 inches.

The first valve covers were baffled Bronco script with a stock PCV valve for a 1969 302. My oil consumption in this combination was a quart every few hundred miles. Not good.

I installed the Summit covers and ran breathers in both. No oil consumption in this configuration but I eventually developed several oil leaks and oil blowing from the breathers. Not good.

I searched for a PCV baffled grommet and found that Moroso p/n 68772 fits the 1.22 in. diameter hole of the Summit valve covers. I pulled the valve cover, removed the metal baffle, and installed the Moroso grommet. This grommet is about 1.25" deep with a slit at the bottom to create a baffle. Drove 200 miles with this and sucked up over two quarts of oil. Not good.

Making no other changes, I installed a Moroso Air-Oil Separator to see what and when the PCV was sucking up the oil. Idle was good but at 2000 RPM it sucked about 1/8 of a cup in five minutes. Not good.

Read about M/E Wagner and their DF-17 Dual Flow PCV Valve from a link posted in a thread here on CB so I bought one. M/E Wagner recommends 3/8" (.375) minimum clearance between the baffle and PCV valve. I pulled the valve cover back off, removed the Moroso grommet and reinstalled the metal plate baffle. I then cut the bottom inch off the Moroso grommet so there are the two lips (top and bottom) to hold it in place like a regular, non-baffled grommet. Bottom of the grommet to the baffle is .390". I used the 1/8" spacer provided by M/E Wagner so the valve sits flush with the grommet.

After proper tuning of the carb and M/E Wagner dual flow PCV valve, idle and 2000 rpm checks showed no oil consumption. 30 mile round trip test drive, split evenly between country road and turnpike, also showed no oil consumption. I drain the air-oil separator about every thousand miles and get around a quarter of a cup of oil. Problem solved.


Parts list:

M/E Wagner DF-17 Dual Flow PCV Valve
Moroso Air-Oil Separator (p/n 85531)
Moroso PCV grommet (p/n 68772)
Summit Racing® Diecast Aluminum Valve Covers (p/n SUM-440406)
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
I have successfully not ran a PCV valve for over 20 yrs.
Current set up is valve covers 1 filler that seals tight with a cap. Nothing else in either covers. I run a -10 hose from a mechanical fuel pump block off plate to the base of the air filter with a bulkhead fitting. Then a 120 degree hose end but no hose pointing towards the carb. All engine venting is inside the air filter. And vapor fumes etc just go down the carb.
All on pretty macho engines with high compression and driven hard. Zero oil consumption.
 

badandy73

Contributor
Broncoholic
Joined
Jul 18, 2007
Messages
219
Following this thread as I'm fighting an oil leak coming from the breather on a set of bronco script valve covers on a new blueprint 306. Figured it was a mfg defect/ bad cover, so blueprint sent me a replacement set. Swapped the new one on (driver's side only) and leak got a lot worse. Pulled it off and inspected the baffle in comparison to the first- original looked to have better coverage, so pinched it shut even more to narrow down the baffle 'window' and also made sure the tabs were laying as flat as possible against the base of the breather tube and put it back together. Didn't make a difference and now back to square one with the original leak.

Passenger side is plumbed with a functioning PCV valve running to the base of the sniper. Blueprint's tech had me verify that it was working correctly and also had me check the breather tube while holding a paper towel over it, wasn't puffing or blowing out excessively. After those checked out, he assures me it isn't excessive blow-by or some other issue with the motor.

One thought is to go to another brand/ style of valve covers with a different style breather setup (or solid oil fill cap as 68ford mentioned). Anyone running something like this with good results?:

summitracing.com/parts/pro-302-135/make/ford
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
I have successfully not ran a PCV valve for over 20 yrs.
Current set up is valve covers 1 filler that seals tight with a cap. Nothing else in either covers. I run a -10 hose from a mechanical fuel pump block off plate to the base of the air filter with a bulkhead fitting. Then a 120 degree hose end but no hose pointing towards the carb. All engine venting is inside the air filter. And vapor fumes etc just go down the carb.
All on pretty macho engines with high compression and driven hard. Zero oil consumption.

I've seen setups similar to what you describe. What about doing the same thing from the valve cover at the rear on one side, have the oil filler on the opposite front side?
I currently run breathers in both, the problem is the breather is at an angle so there will always be some residue that leaks out the bottom side of the breather below the tube opening. If you had a tube that went into the valve cover and then angled to where the breather sat straight up would help with that. Haven't found such an animal but could be made i guess.

I just recently pulled my 395 that was built in 2005, I didn't run a PCV but it had started smoking under hard throttle, still ran great. I decided to build a new roller motor. When tearing down the 395 there was basically no wear in the cylinders, however when I took the heads (Edlebrock RPM Performer) to the machine shop for rework to go on the new engine it was found that every intake valve and guide was bad. These heads were bought new and bolted on, machine shop said the guides and the seats on the intake valves were out of alignment and is why they had worn so bad. I kept one of the valves and have it on my desk as a reminder to not just bolt on new parts without checking them out. That's where my oil was coming from. Nothing else I saw on this engine over 15 years not running a PCV concerned me.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Anyone running something like this with good results?:

https://summitracing.com/parts/pro-302-135/make/ford

I ran a set of those for a long time, they always leaked. Figured out why the other day, the holes were drilled out too big.
One was 1.2845" ans the other 1.2895". I took a chance on another set of Proform covers https://www.summitracing.com/parts/pro-302-003
First thing I did when the came in was measure the holes. Both are 1.18". Now the grommets fit and seal properly, mo more leaks! Her are pics
of the old covers.
 

Attachments

  • Blowby1.jpg
    Blowby1.jpg
    78.2 KB · Views: 120
  • Blowby2.jpg
    Blowby2.jpg
    78.9 KB · Views: 127

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Anyone running something like this with good results?:

summitracing.com/parts/pro-302-135/make/ford

I didn't know those existed until now. I just ordered a set for my new build. Those covers will put the breather in more of an upright position which will help with oil residue not getting trapped and leaking out. Be a while before I'm up and running though, couple months.

Thanks for the link.
 
Top