• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley Sniper Hyperspark

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
I just installed a Holley Hyperspark ignition, distributor, and coil. I am having a hard time finding the timing settings for a Blueprint 306. I had it set at 15 idle, 36 cruise and WOT. I was running really hot so I set it at 12 idle and it ran much cooler. My question is what should the timing be set at? I'm gonna stick with 12 idle and 36 WOT but don't know cruise? Any help will be appreciated.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Interested to hear what you come up with. Because just three degrees of initial should not make a big difference in how hot an engine runs, and going more retarded usually has the effect of it getting hotter, not cooler like in your experience.

You've tried calling Blueprint? Or has this all happened just over the weekend? Is it possible that it was just running hot during the initial running because some engines run hot when new, and there may even have been an air pocket that finally burped out?

What temperature is "hot" in this case, and under what conditions were you running the engine?

Thanks

paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oh, and are you certain that your damper ring timing marks match the timing pointer on your particular engine? Did you get your engine as a complete engine with timing cover, damper and all?

Paul
 
OP
OP
H

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
Engine came with negative coil and generic distributor. This is a Covid upgrade. Engine never ran hot (185 ish) and after hyperspark it ran 205 on a 15 mile run to town. I took out the thermostat due to being in Hawaii but not sure if that had an effect. I will call Blueprint tomorrow and inquire.
 

BUCKWILD

Sr. Member
Joined
Jun 20, 2016
Messages
355
Loc.
Butte county
so gearing, trans and tire size will help us. aluminum heads or iron? i would think with no info on your set up 25-28 at cruse
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I took out the thermostat due to being in Hawaii but not sure if that had an effect.

Well I would put one back in, at whatever temp they recommend (probably 180-195 range) or they may void any warranty you have. You literally can do damage to an engine that never gets up to running temp. Of course, yours obviously gets up to running temp, but removing the thermostat is just a Band-Aid for other issues and does not let it warm up efficiently or effectively. Keeps both carbs and EFI running rich sometimes too.
How quickly does yours come up to temperature?

I can't argue with success, so if you still come up to temp quickly you're likely not harming anything. Just that it "can" do bad things and is not needed when all else is working properly.
If all is working properly, with the right equipment a temp range of 195-205 is right in the sweet spot in fact. And for the rest of us it also makes the heaters work great!
Likely your idea of "turning on the heater" though, is removing the top and running out in the sun!;D

Just to be sure I have the timeline correct here though, when exactly did you remove the thermostat? Before/after/during the Hyperspark swap?
And are you letting the computer control timing, or is the ignition on standard mechanical and vacuum advance?

Paul
 
OP
OP
H

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
Bronco edition, aluminum heads, stock 73 gears, Chevy 700R4 trans, 31-10.5-15 tires
 
OP
OP
H

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
Removed thermostat after hyperspark, computer controlled timing. Spent 2 hours on the phone with Holley and he was baffled. I sent in a logged run after the thermostat removal and haven’t heard back yet.
 
OP
OP
H

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
If 3 degrees retarded makes it hotter I should go to 20 degrees idle?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
We can't say that yet, since in your case the three degrees also coincided with it running cooler. So no common correlation yet.

Are you setting your base timing manually, then checking it again when the computer takes over? Or are you setting base timing in the computer? I'm not sure how the Holley works in that regard, so just asking to clarify stuff. Once the computer takes over it often advances the timing substantially at idle and low load conditions. Which is why I was wondering if you checked the timing while running under computer control.

As far as "should you go to 20 degrees" you can only know if you try. Timing is something that is almost always experimented with by the end-user of an engine. Especially when that engine has nothing in common with a stock engine that has specific settings arrived at by the factory engineers. And even those we mess with a lot after we get them!

So all I can say is, try it and see how it works. Try different settings in small increments (say two or three degrees at a time) and see if you have any pinging/pre-ignition/rocks-in-a-can rattling, or sluggishness, or increased or decreased heat.
it's all an experiment from here on out.

Paul
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
But definitely put the thermostat back in. When I bought my Bronco, unbeknownst to me, the PO had no thermostat installed. Crazy temperature swings.
I put a thermostat in and it stays more consistent. But Paul is right, a newish rebuilt motor tends to run a little warm for a while.
 
OP
OP
H

hapa23

New Member
Joined
Mar 13, 2016
Messages
22
Yes, I set the static timing on the handheld and shot the timing manually so the manual timing coincides with the handheld.
 

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
Did you resolve this? I found a couple forums stating that the temp sensor with the Holley can be 10-15 degrees off, and to get an ACdelco temp sensor. That fixed their issue.
 
Top