• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Throttle Linkage

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
What am I missing here? I’ve got the bar circled in red adjusted all the way in, but still only have like 1/2 throttle. It seems like it needs to be able to come in another 1 1/2” or so.

02BCBE06-5655-4E1F-B08D-C3D79ED6845B.jpeg


This motor is out of a ‘74 Bronco and the linkage is off of a ‘69 but I don’t see how that could make a difference. The carb does have some slight variations so maybe that’s it?
 

Attachments

  • B3FEF125-8660-4AED-A41B-4B5290872D8B.jpeg
    B3FEF125-8660-4AED-A41B-4B5290872D8B.jpeg
    213.6 KB · Views: 132
  • 308FDB1B-3A52-41E0-850C-1768F9CC8DB8.jpeg
    308FDB1B-3A52-41E0-850C-1768F9CC8DB8.jpeg
    231.5 KB · Views: 109
  • CD16007B-5D01-44F3-B1BC-DDD379BE9262.jpeg
    CD16007B-5D01-44F3-B1BC-DDD379BE9262.jpeg
    269.7 KB · Views: 81
  • 2756AE12-BB44-46DA-91C4-6FB71F19BF02.jpeg
    2756AE12-BB44-46DA-91C4-6FB71F19BF02.jpeg
    205.8 KB · Views: 99
Last edited:

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
The link to the firewall needs to be reconnected. This will steady that whole tower in the middle that pivots so that it doesnt move when you push on the gas pedal.

Sent from my SM-G981U using Tapatalk
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
Also, get a new spring for the throttle return. The one in your photo is all stretched out and won't last long.

Sent from my SM-G981U using Tapatalk
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Both good points, but neither of those fixes the immediate issue. I had the linkage to the firewall in place during testing I’m just waiting for one of those little clips so I can reconnect it for good.

The real issue is I can’t get the travel I need with it set up as it is currently.
 

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Not sure if this helps but here a couple pictures of the set up on my 76 with auto trans. From what I see. Maybe ditch the mechanism between the carb and firewall. Then install a linkage that connect to the ball connection on the throttle. You can see the linkage in the first picture. Its disconnected and vertical attached to the firewall levers.
 

Attachments

  • DB4B0EE9-A1DB-4038-BEBE-7E75AA87BE25.jpeg
    DB4B0EE9-A1DB-4038-BEBE-7E75AA87BE25.jpeg
    258.6 KB · Views: 129
  • D65E0734-FB51-429A-847B-D26142EEB70A.jpeg
    D65E0734-FB51-429A-847B-D26142EEB70A.jpeg
    251.4 KB · Views: 99

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
That is the equalizer bracket. It corrects for body to engine movements. The link to the firewall is the reference point to the throttle linkage input. The difference between the two is the amount the throttle is opened.

If you have someone hold the throttle to the floor and move the linkage that attaches to the firewall you will see the throttle on the carburator moves as you are moving the firewall linkage.

Many have removed the linkage and went to a solid connection from the throttle to the carb. For a pavement princess you will probably never notice. I had that once and hated it. On a rough road the linkage was always moving about. either pumping the throttle on the carb up an down if you forced the pedal steady. Or if you rode with it, you could feel the pedal going up and down against your shoe.
And often the reason people change over to a throttle cable.

You have all the parts. Once you understand the reference point on the firewall a little more and get that dialed in it will be fine. You are stock enough that stock works.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Is this bolt supposed to be there? Right now I can see no way that the firewall rod (stabilizer assembly?) can do anything.
33590E60-0463-49DD-8BC1-96DB326D1100.jpeg
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Looking at that picture, and the original, someone did some butchery. That is a serrated nut, installed backwards. No, that should not be there.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Looking at that picture, and the original, someone did some butchery. That is a serrated nut, installed backwards. No, that should not be there.
As in that whole part of the bracket should be able to pivot on the bar below the serrated nut, correct?
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Yep I took that bolt out and made a couple of adjustments and now it looks like I’ve got full travel. Thanks guys.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The issue might be that a '74 did not have that firewall anchor point and the '69 did. They stopped using it sometime in '73 I believe.
The setup came with the engine? If so yours might have been tweaked to work without the arm.

As said, if you're going to use the arm from the firewall you should not have that bolt there. I don't think I've ever seen one used like that, but I really did not pay that much attention to those details on every Bronco I looked at.
As was also mentioned, you can start from full-throttle in your adjustments too. Seems to me that the early setups were pivoted slightly farther forward via that firewall arm, then the other stuff matched up to it better. It's definitely a funky setup (clever, but still funky) and luckily for most it never had to be adjusted once it came from the factory. But once modified or taken apart fully, or parts swapped in, all bets were off.
Keep at it and I'm sure you'll find a happy medium.

Paul
 
Top