• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Axle Shaft Length

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
So I got my new Wildhorses D44 axle shafts today. I have a narrowed HP D44 out of a big Bronco. I had to get a driver side inner out of the big Bronco and a passenger side inner out of the EB.

The driver side length looks good to me. It seats all the way and is flush on the inside of the carrier. But, the passenger side bottoms out and is still sticking out of the housing by about 5/8”
CC749477-4367-4E70-BCDF-A8C8B2C53729.jpeg
8F55F6AC-5C9F-473B-86CC-611237D05299.jpeg
683E85D3-64C6-40A8-98BD-D0EC8C44BA10.jpeg

I measured the length and it is in fact the EB length of 27 15/16”. So my guess is whoever narrowed this housing went a little overboard?

How much spline do I need left to engage with the carrier? The splines are right at 2 3/4”. Is it as simple as cutting 5/8” off of the end (making sure not to mess up the splines) and then call it a day? This would leave me with roughly 2 1/8” left of splined end, call it 2” after waste.

6321E45D-F2C4-4458-AE0C-52552D08C123.jpeg
 

Attachments

  • 823AABE4-DAE0-45D7-B5F5-D8AEB9B0C912.jpeg
    823AABE4-DAE0-45D7-B5F5-D8AEB9B0C912.jpeg
    200.1 KB · Views: 62

walls

Full Member
Joined
Oct 4, 2010
Messages
222
Yes , I would and have , cut what you need off with a chop saw or grinder with a cutting disc and re bevel the 45° on the end and you are good to go.

Myself by looking at the pics would take 3/16 or so off the driver side also, the metal is going to grow a bit when it warms up and possibly bind on the carrier, it will do you no good sticking out past where the carrier is splined so why not play it safe and take a hair off.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
That’s too bad, but not unexpected. In order to keep the original early bronco WMS, you need to take 6 inches off the right, and 5/8 off the left. Somebody shortened one side and lopped off the whole 6-5/8. The end result is what you see. You can just cut off the additional 5/8 and you’ll be fine. The wild h axles have a ton of seal surface, so cutting off 5/8 won’t hurt.
The short side looks good. Don’t forget that the axle does not run that deep into the tube. When you attach the spindle and hub, it will pull out a good 1/8.

Did you notice that you have a Trac-loc in your front end? They do not provide traction, and they don’t lock. And they are weak, and they break, and I hate them. (Although I’ve made plenty of $$$ fixing them…) if you have anything else, including a factory open carrier, I’d swap it now.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
That’s too bad, but not unexpected. In order to keep the original early bronco WMS, you need to take 6 inches off the right, and 5/8 off the left. Somebody shortened one side and lopped off the whole 6-5/8. The end result is what you see. You can just cut off the additional 5/8 and you’ll be fine. The wild h axles have a ton of seal surface, so cutting off 5/8 won’t hurt.
The short side looks good. Don’t forget that the axle does not run that deep into the tube. When you attach the spindle and hub, it will pull out a good 1/8.

Did you notice that you have a Trac-loc in your front end? They do not provide traction, and they don’t lock. And they are weak, and they break, and I hate them. (Although I’ve made plenty of $$$ fixing them…) if you have anything else, including a factory open carrier, I’d swap it now.
And the snowball keeps rolling haha. Thanks again for dropping some knowledge. Makes sense about the 6 5/8” overall.

I didn’t notice that, I thought it was just an open carrier but what do I know? (not a lot)

I’m re-gearing the rear as we speak and once I am confident I like the 4.56s I’ll be doing (paying to have done) the front end. It’s 3.50s now. I’m sure I’ll have questions when the time comes. Just gonna run around in 2 wheel drive for a bit for now.
 

walls

Full Member
Joined
Oct 4, 2010
Messages
222
Most likely shortened one side to get the yoke where he wanted it to line up with the transfer case for a nice straight front shaft. . I did the same on my dana 60 out of a 2000 f350. Sent the axle out to Moser engineering and they cut and resplined the axle for like 60 bucks.
 

walls

Full Member
Joined
Oct 4, 2010
Messages
222
Does seem like a lot of work to shorten the axle tube on one side 5/8.
 
Top